24
edits
Back-lit switches: Difference between revisions
add images of switch repair
No edit summary |
(add images of switch repair) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 20: | Line 20: | ||
The contacts can break off from the support, giving no or intermittent conduction. It is possible to solder the contact to the support if care is taken to apply solder only to the center, or to transplant an unused contact (see example photo). | The contacts can break off from the support, giving no or intermittent conduction. It is possible to solder the contact to the support if care is taken to apply solder only to the center, or to transplant an unused contact (see example photo). | ||
==Repairing sticky ganged switches== | |||
While Tek documentation states that Series 71 switches are not repairable, this is not strictly true. If the problem is a gang of interlocked switches where it is difficult to change which switch is depressed, this can be resolved without disassembly. | |||
On switches using a metal light guide, a raised rectangle exists on the housing. Cutting through this with an x-acto knife will expose the mechanical interlock. Dispense electrical contact lube into this hole and work the switches. I had best luck alternating lube and alcohol; I believe the latter helped to transport the lube through the switch. See photos in gallery below. | |||
It should be possible to lubricate switches with acrylic light pipe similarly, though they lack the handy raised mark. | |||
==See also== | |||
* [[Media:Repairing tek-made board-mounted push-button switches.pdf|Repairing Tek-Made Board-Mounted Push-Button Switches]] | |||
* [[Pushbutton switches]] | |||
==History== | ==History== | ||
From [https://vintagetek.org/wp-content/uploads/2019/06/On-The-History-And-Environment-Of-Tektronix.pdf The History and Environment of Tektronix]: | From [https://vintagetek.org/wp-content/uploads/2019/06/On-The-History-And-Environment-Of-Tektronix.pdf On The History and Environment of Tektronix]: | ||
<blockquote> | <blockquote> | ||
So, one day, Howard said, "the [7000-series] plug-ins will be 5¼ inches in height." | So, one day, Howard said, "the [7000-series] plug-ins will be 5¼ inches in height." | ||
| Line 28: | Line 40: | ||
[[Oliver Dalton]] recalls the decision to reduce the plug-in height as a traumatic one:<br /> | [[Oliver Dalton]] recalls the decision to reduce the plug-in height as a traumatic one:<br /> | ||
"The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the [[7000 series readout system|IC read-out effort]]: 1) new lit push-buttons ... we needed 25 on a panel; 2) [[cam switch]]es - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) [[miniature relays|relays]] ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers. | "The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the [[7000 series readout system|IC read-out effort]]: 1) new lit push-buttons ... we needed 25 on a panel; 2) [[cam switch]]es - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) [[miniature relays|relays]] ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers. | ||
[...] | |||
Howard Vollum was the person who started the push-button effort because he wanted small buttons. Some of the key inputs on the design came from the Model Shop, such as from [[John Winkelman]] who came up with a latch mechanism. | |||
</blockquote> | </blockquote> | ||
| Line 37: | Line 53: | ||
Tek 7k DPDT PCB switch 1.jpg | Dual DPDT switch interior (mV / mρ mode switch from a [[7S12]]) | Tek 7k DPDT PCB switch 1.jpg | Dual DPDT switch interior (mV / mρ mode switch from a [[7S12]]) | ||
Tek 7k DPDT PCB switch 2.jpg | Tek 7k DPDT PCB switch 2.jpg | ||
7A12 switch.jpg | Sticky switch, before repair | |||
Switch xacto.jpg | Cutting a hole for lubrication | |||
Switch lube.jpg | Injecting lubricant | |||
</gallery> | </gallery> | ||
[[Category:Repair issues]] | [[Category:Repair issues]] | ||
[[Category:Electromechanical components]] | [[Category:Electromechanical components]] | ||