564: Difference between revisions
(→564B) |
|||
Line 91: | Line 91: | ||
Tek 564b with viewing hood.jpg|564B with viewing hood on a [[201]] cart | Tek 564b with viewing hood.jpg|564B with viewing hood on a [[201]] cart | ||
Tek 564b with viewing hood2.jpg|564B with viewing hood on a [[201]] cart | Tek 564b with viewing hood2.jpg|564B with viewing hood on a [[201]] cart | ||
Heerenveen 564b with 3a74 and 3b3.jpg|564B with [[3A74]] and [[3B3]] made in The Netherlands | |||
</gallery> | </gallery> | ||
Revision as of 13:53, 26 April 2021
The Tektronix 564 is the storage scope of the 560 series, introduced in June 1962. It takes two 2- or 3-series plug-ins. The RM564 is the rack-mount version.
The 564 is a tube-based oscilloscope, whereas a later version, the 564B (1969), is fully solid state. Mod 121N added auto-erase. The screen has bi-stable storage in two 4 cm × 10 cm sections, allowing independent saving and erasing of the upper and lower half.
The 564 was one of the mainframes offered for the Engine Analyzer package.
Key Specifications
Bandwidth | determined by plug-in (up to 25 MHz available) |
---|---|
Writing speed | ≥25 Div/ms with T5640-200 |
Storage time | At least 1 hour |
CRT | 8×10 Div @ 1 cm/Div, external graticule; tube 154-0410-00/154-0565-00 (standard, P200) / 154-0418-00/154-0565-01 (fast writing speed, P201); 3.5 kV acceleration |
Calibrator | 0.2 mV to 100 Vp-p in 18 steps, square wave at line frequency |
Power | 105−125 V or 210−250 V, 50 to 400 Hz, 250 W maximum; Convection cooling, thermal cut-off switch |
Weight | ~14 kg (30.5 lb) without plugins |
Steve Ditter says:
Tek offered two phosphors for the 564. You can determine which one you have by reading the CRT part number, visible in the window in the shield where the deflection plate connections are. 154-0410-00 is P200, which was the standard tube. The 154-0418-00 is the P201, which has faster writing rate, but at the expense of about 30% shorter useful life.
Links
- Tek 564 / RM564 @ barrytech.com
- J.Evans's 564 page
- Ralph K's 564 pictures page
- A 564 @ YouTube / another one
Internals
As in all 560 series scopes, the left plug-in directly drives the vertical deflection plates of the CRT, and the right plug-in directly drives the horizontal deflection plates.
Accessories
The 012-0102-00 Storage Oscilloscope Control Unit that works with the 549 also works with the 564B but not the 564. It provides (corded) remote reset of the sweep and independent erase of the upper and lower storage areas.
Pictures
564
-
-
-
Tektronix 564 Front Panel
-
564, Display
-
Tektronix 564 Display (in Storage Mode)
-
Tektronix 564 Back
-
Tektronix 564 Left
-
Tektronix 564 Right
RM564
-
-
RM564, Switch for storage
-
RM564, Chassis
-
RM564, Chassis bottom
-
R564B w auto-erase and 3A6 and 3B3
564B
-
564B
-
564B
-
564B
-
564B
-
564B on cart
-
564B with viewing hood on a 201 cart
-
564B with viewing hood on a 201 cart
Schematics
-
564 Block Diagram
-
564 Power Supply
-
564 Interconnecting Sockets
-
564 CRT Circuit
-
564 Calibrator
-
564 Storage Circuit
Versions
-
564 version 1
-
564 version 2
-
564 version 3
Internals
-
Tektronix 564 Left Internals
-
Tektronix 564 Left Internals
-
Tektronix 564 Left Internals
-
Tektronix 564 Left Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 Right Internals
-
Tektronix 564 HV Section - Cover Removed
Third-party
-
Physionic 671 Ultrasonic Imager, based on 564
-
Physionic 671 Ultrasonic Imager, based on 564
-
Physionic 671 Ultrasonic Imager, based on 564
-
Physionic 671 Ultrasonic Imager, based on 564
-
Physionic 671 Ultrasonic Imager, based on 564
-
Physionic 671 Ultrasonic Imager, based on 564