111: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 1: Line 1:
The '''Tektronix Type 111 Pretrigger Pulse Generator''' produces two pulse signals: one to trigger an oscilloscope sweep and a main output pulse to stimulate the device under test.  The trigger pulse comes between 30 and 250 nanoseconds before the output pulse; this is controlled by a knob on the 111.  This gives adequate time for the oscilloscope to start sweeping so that the leading edge of the input or output signals of the device under test can be viewed.  The alternative is to have a [[delay line]] in the signal path, after the trigger pickoff, but delay lines degrade transient performance.  Using a pretrigger eliminates the need for a delay line in the vertical signal path and therefore enables accurate high-speed measurements.   
The '''Tektronix Type 111 Pretrigger Pulse Generator''' produces two pulse signals, one to trigger an oscilloscope sweep and a main output pulse to stimulate the device under test.   


The main output pulse of the Type 111 is produced by an avalanche transistorThe risetime is specified as "0.3 nanosecond" in the Auxiliary Equipment
The trigger pulse comes between 30 and 250 nanoseconds before the output pulse; this is controlled by a knob on the 111.  This gives adequate time for the oscilloscope to start sweeping so that the leading edge of the input or output signals of the device under test can be viewed.  The alternative is to have a [[delay line]] in the signal path, after the trigger pickoff, but delay lines degrade transient performance.  Using a pretrigger eliminates the need for a delay line in the vertical signal path and therefore enables accurate high-speed measurements.  For a stable display, low jitter of the delay between pretrigger and main pulse is essential.
section at the end of the Type [[N]] manual, and "equal to or less than 500 picoseconds" in the Characteristics section of the 111 manual.


For a stable display, it is essential for the delay between pretrigger and main pulse to be stable, free of jitter. The pretrigger-to-main pulse jitter of the Type 111 is specified as 100ps.  The repetition rate is 10/sec to 100,000/sec.  The main output pulse amplitude is specified to be at least 10 volts into 50 ohms.
{{BeginSpecs}}
{{Spec | Pulse repetition rate | 10 Hz to 100 kHz, or by external trigger }}
{{Spec | Rise time | <500 ps }}
{{Spec | Pre-trigger | 30−250 ns variable with additional calibrated "+1 ns" switch, jitter ≤100 ps }}
{{Spec | Output amplitude | ≥10 V (selectable polarity) into 50 Ω }}
{{EndSpecs}}


==Internals==
The main output pulse of the Type 111 is produced by an avalanche transistor. 
==Manuals==
* [http://bama.edebris.com/download/tek/111/Tek%20111.pdf Tektronix 111 Manual (PDF)]
* [http://bama.edebris.com/download/tek/111/Tek%20111.pdf Tektronix 111 Manual (PDF)]
* [http://w140.com/tek_fcp/tek_type_111_factory_cal_proc.pdf Tektronix 111 Factory Calibration Procedure (PDF)]
* [http://w140.com/tek_fcp/tek_type_111_factory_cal_proc.pdf Tektronix 111 Factory Calibration Procedure (PDF)]


==Notes==
The Auxiliary Equipment section in the [[N|Type N]] manual says the rise time is 300 ps.  The 111 front panel and manual specify <500 ps.
==Pictures==
<gallery>
<gallery>
Tek 111 front.jpg|Front View
Tek 111 front.jpg|Front View

Revision as of 05:22, 19 February 2019

The Tektronix Type 111 Pretrigger Pulse Generator produces two pulse signals, one to trigger an oscilloscope sweep and a main output pulse to stimulate the device under test.

The trigger pulse comes between 30 and 250 nanoseconds before the output pulse; this is controlled by a knob on the 111. This gives adequate time for the oscilloscope to start sweeping so that the leading edge of the input or output signals of the device under test can be viewed. The alternative is to have a delay line in the signal path, after the trigger pickoff, but delay lines degrade transient performance. Using a pretrigger eliminates the need for a delay line in the vertical signal path and therefore enables accurate high-speed measurements. For a stable display, low jitter of the delay between pretrigger and main pulse is essential.

Key Specifications

Pulse repetition rate 10 Hz to 100 kHz, or by external trigger
Rise time <500 ps
Pre-trigger 30−250 ns variable with additional calibrated "+1 ns" switch, jitter ≤100 ps
Output amplitude ≥10 V (selectable polarity) into 50 Ω

Internals

The main output pulse of the Type 111 is produced by an avalanche transistor.

Manuals

Notes

The Auxiliary Equipment section in the Type N manual says the rise time is 300 ps. The 111 front panel and manual specify <500 ps.

Pictures