1502: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 13: Line 13:
sensitivity although it is much easier to destroy.
sensitivity although it is much easier to destroy.


There are four key parts in the 1502 that make repair difficult.  The origonal sampling gate
There are four key parts in the 1502 that make repair difficult.  The origional sampling gate
(CR1732, tek 152-0631-00) is NLA, but Avago RF Schottky barrier diodes in the SOT series pair package
(CR1732, tek 152-0631-00) is NLA, but Avago RF Schottky barrier diodes in the SOT series pair package
(Avago HSMS-2822, HSMS-282C) are a close substitute.  There is a snap-off diode (CR1632, tek 152-0335-01)
(Avago HSMS-2822, HSMS-282C) are a close substitute.  There is a snap-off diode (CR1632, tek 152-0335-01)
in the samping gate pulse shaper that is also NLA but it usually doesn't fail.  The first pulse shaping TD
in the samping gate pulse shaper that is also NLA but it usually doesn't fail.  The first pulse shaping TD
(CR1609, tek 152-0140-01) is a 10mA, 8pF was a fairly common TD and there are Russian substitutes
(CR1609, tek 152-0140-01, 10mA, 8pF) was a fairly common TD and there are Russian substitutes
available.  The primary fast pulse TD (CR1703, tek 152-0489-00) is simply NLA.  Good Luck!
available.  The primary fast pulse TD (CR1703, tek 152-0489-00, 21mA, 1.5pF) is simply NLA.  Good Luck!
 
If you want to design a replacement, I suggest looking at Analog Devices ADCMP580, and Starecki and Misiaszek's
paper "Low cost programmable pulse generator with very short rise/fall time".


The other common failure is the battery.  The power supply was designed to protect both the instrument
The other common failure is the battery.  The power supply was designed to protect both the instrument
Line 26: Line 29:
will fool the power supply protection circuit into thinking that it's charging a valid battery.
will fool the power supply protection circuit into thinking that it's charging a valid battery.


 
Service Manuals:
* [http://w140.com/TEK-1502-OM-SM.pdf Tektronix 1502 Service Manual (PDF)]
* [http://w140.com/TEK-1502-OM-SM.pdf Tektronix 1502 Service Manual (PDF)]
* [http://w140.com/tek_1502b_service.pdf Tektronix 1502B Service Manual (PDF)]
* [http://w140.com/tek_1502b_service.pdf Tektronix 1502B Service Manual (PDF)]
* [http://w140.com/tek_1502c_service.pdf Tektronix 1502C Service Manual (PDF)]
* [http://w140.com/tek_1502c_service.pdf Tektronix 1502C Service Manual (PDF)]
Note that the manuals for the 1502B and 1503C are still available from Tektronix.
<gallery>
Image:Tek1502-top.JPG|Top boards of the 1502
Image:Tek1502-bottom.JPG|Underside of 1502 with stripline sampler and pulser exposed
Image:Tek1502-samplinggate.JPG|Sampling gate near the BNC end of stripline
Image:Tek1502-pulser.JPG|Pulser end of the stripline
Image:Tek1502-td.JPG|Pulser TD removed from stripline
Image:Tek1502-tdcurve.JPG|Pulser TD curve traced with a 576
</gallery>

Revision as of 15:16, 14 February 2012

The Tektronix 1502 is a series of Time Domain Reflectometers commonly used to test coaxial cables athough they have many other uses. The US military was a major purchaser; most of the first series (the 1502, no letter) will be found surplus with some sort of US military property ID tag and an NSN sticker.

The first version used a CRT and is almost completely analog along with some descrete digital logic used to prefire and fire the tunnel diode pulser. The later models (1502B/C) used an LCD display and a microprocessor. The other major difference is the line charging method. The 1502 uses a fast (36ps) tunnel diode pulser, the later models used a half sine wave to charge the line. The TD pulser, with it's Dirac delta edge gives much better short range sensitivity although it is much easier to destroy.

There are four key parts in the 1502 that make repair difficult. The origional sampling gate (CR1732, tek 152-0631-00) is NLA, but Avago RF Schottky barrier diodes in the SOT series pair package (Avago HSMS-2822, HSMS-282C) are a close substitute. There is a snap-off diode (CR1632, tek 152-0335-01) in the samping gate pulse shaper that is also NLA but it usually doesn't fail. The first pulse shaping TD (CR1609, tek 152-0140-01, 10mA, 8pF) was a fairly common TD and there are Russian substitutes available. The primary fast pulse TD (CR1703, tek 152-0489-00, 21mA, 1.5pF) is simply NLA. Good Luck!

If you want to design a replacement, I suggest looking at Analog Devices ADCMP580, and Starecki and Misiaszek's paper "Low cost programmable pulse generator with very short rise/fall time".

The other common failure is the battery. The power supply was designed to protect both the instrument and the battery from abuse, so any failure will cause the power supply to latch up (via Q6547/Q6549) and the unit will appear dead. The pack is rebuildable with NiCd battery cells. To operate without a battery in place use a 200 to 270 ohm 10W power resistor in series with a 2200uF cap (>25V); this will fool the power supply protection circuit into thinking that it's charging a valid battery.

Service Manuals:

Note that the manuals for the 1502B and 1503C are still available from Tektronix.