1A4: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
(5 intermediate revisions by 3 users not shown)
Line 9: Line 9:
series=[[500-series scopes]] |
series=[[500-series scopes]] |
manuals=
manuals=
* [http://w140.com/mmm/tek-1a4.pdf (PDF)]
* [http://w140.com/mmm/tek-1a4.pdf Tektronix 1A4 Manual (PDF)]
* [http://bama.edebris.com/manuals/tek/1a4 1A4 manual on BAMA (offline?)]
* [http://bama.edebris.com/manuals/tek/1a4 1A4 manual on BAMA (offline?)]
* [[Media:Tek 1a4 fcp jan 1967.pdf‎|Tektronix 1A4 Factory Calibration Procedure, January 1967]]
}}
}}
The '''Tektronix Type 1A4''' is a 1-series vertical plug-in for [[500-series scopes]].
The '''Tektronix Type 1A4''' is a 1-series vertical plug-in for [[500-series scopes]].
Line 28: Line 29:
Like the Type [[1A2]] and unlike the Type [[1A1]],  
Like the Type [[1A2]] and unlike the Type [[1A1]],  
the Type 1A4 has a Trigger Output selector that controls  
the Type 1A4 has a Trigger Output selector that controls  
which channel provides triggering when the mainframe trigger is in Plug-In mode.
which channel provides triggering when the mainframe trigger is in Plug-In mode,
for scopes having this feature ([[544]], [[546]], [[547]], [[549]], [[556]], late [[555]]).


==Specifications==
==Specifications==
Line 40: Line 42:
The signal path of each channel of the 1A4 is as follows.   
The signal path of each channel of the 1A4 is as follows.   
First the signal passes through the attenuators.   
First the signal passes through the attenuators.   
Then it is clamped by two diodes and applied to the the gate of a JFET source follower.   
Then it is clamped by two diodes and applied to the gate of a JFET source follower.   
The source of the source follower is the trigger pickoff point.   
The source of the source follower is the trigger pickoff point.   
From there the vertical signal path goes through an NPN emitter follower  
From there the vertical signal path goes through an NPN emitter follower  
Line 59: Line 61:
Tek 1a4 rear n1.jpg
Tek 1a4 rear n1.jpg
Tek 1a4 frontclose n1.jpg
Tek 1a4 frontclose n1.jpg
Image:1a4 front.jpg
1a4 front.jpg
Image:1a4 right2.jpg
1a4 right2.jpg
Image:1a4 top.jpg
1a4 top.jpg
Image:1a4 bottom.jpg
1a4 bottom.jpg
</gallery>
</gallery>


[[Category:500 series plugins]]
[[Category:500 series plugins]]

Revision as of 14:33, 8 June 2019

Template:Plugin Sidebar 2 The Tektronix Type 1A4 is a 1-series vertical plug-in for 500-series scopes. It has four input channels and 50 MHz bandwidth.

Type 1A4 was introduced in 1967 and lasted until the end of the 500-series scopes line.

The four channels are grouped into two groups of two channels. Type 1A4 has a special "trace slaving" mode which, when used in a 547 mainframe, allows channels 1 and 2 to be displayed using the A time base, and channels 3 and 4 to be displayed with the B time base. This allows high-speed and low-speed signals to be displayed together, similar to what a dual-beam scope can do, but without some of the cost and complexity.

Like the Type 1A2 and unlike the Type 1A1, the Type 1A4 has a Trigger Output selector that controls which channel provides triggering when the mainframe trigger is in Plug-In mode, for scopes having this feature (544, 546, 547, 549, 556, late 555).

Specifications

please add

Maximum channel sensitivity is 10 mV/div, but a Signal Out jack makes it possible to cascade two channels for approximately 200 μV/div AC with about 20 Hz - 1 MHz bandwidth.

Internals

The signal path of each channel of the 1A4 is as follows. First the signal passes through the attenuators. Then it is clamped by two diodes and applied to the gate of a JFET source follower. The source of the source follower is the trigger pickoff point. From there the vertical signal path goes through an NPN emitter follower followed by an NPN differential amplifier, at which point the signal becomes differential. Next, the signal passes through an analog multiplexer made with 1N4152 silicon switching diodes. After the multiplexer network, the signal passes through a common base amplifier followed by 6DJ8 tube operating in common grid configuration.

Pictures