1M1: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 16: Line 16:
used for calibrating [[500-series scopes]].   
used for calibrating [[500-series scopes]].   


It is a multifunction replacement for the [[P|Type P Pulser]], the [[TU-2|TU-2 Test Load]], and the [[EP-53|EP-53 Gain Set Adaptor]].   
It is a multifunction replacement for the [[P|Type P Pulser]], the [[TU-2|TU-2 Test Load]],
and the [[EP-53|EP-53 Gain Set Adaptor]].   


It is used for calibrating the mainframe's step response and gain, checking  
It is used for calibrating the mainframe's step response and gain,
dual-trace operation, common mode rejection, and power supply regulation.   
checking dual-trace operation, common mode rejection, and power supply regulation.   


(500-series mainframes are designed to have 10 div/Volt response to differential signals from the plug-in, and zero response to common-mode signals.)
(500-series mainframes are designed to have
10 div/Volt response to differential signals from the plug-in,
and zero response to common-mode signals.)


It contains a transistor multivibrator,
It contains a transistor multivibrator whose output is sharpened
whose output is sharpened through Tek-made Gallium-Arsenide diodes (later production used silicon),  
through Tek-made Gallium-Arsenide diodes (later production used silicon),  
a dual-trace circuit using [[12AT7]] and [[6AL5]] tubes, and various load resistors.
a dual-trace circuit using [[12AT7]] and [[6AL5]] tubes, and various load resistors.
It does not have the Type P's short operating life, because it does not use a [[mercury switch]].
It does not have the Type P's short operating life because it does not use a [[mercury switch]].


This instrument went through several names. At its [[introduced in 1964|1964]] introduction, it was the '''TU-7'''.   
This instrument went through several names.
Some early Tek-internal instruments for design, manufacturing, and calibration had TU (Test Unit) nomenclature.   
At its [[introduced in 1964|1964]] introduction, it was the '''TU-7'''.   
(Other examples include the [[TU-75B]] Variac, the TU-?? dim-bulb fixture, and the [[TU-50]] sine/square/pulse generator.)   
Some early Tek-internal instruments for design,
manufacturing, and calibration had TU (Test Unit) nomenclature.   
(Other examples include the [[TU-75B]] Variac, the TU-?? dim-bulb fixture,
and the [[TU-50]] sine/square/pulse generator.)   


In 1965, it was renamed '''Type 1M1''' to fit into the letter-series nomenclature like its predecessor.   
In 1965, it was renamed '''Type 1M1''' to fit into the letter-series nomenclature like its predecessor.   
Line 43: Line 49:


<gallery>
<gallery>
File:067-0521-00 1.JPG
067-0521-00 1.JPG
File:Tek 1m1 front.jpg
Tek 1m1 front.jpg
File:Tek 1m1 right.jpg
Tek 1m1 right.jpg
File:Tek 1m1 left.jpg
Tek 1m1 left.jpg
Tek tu-7 c1.jpg|TU-7 variant with five repetition rates
Tek tu-7 c1.jpg|TU-7 variant with five repetition rates
Tek tu-7 c2.jpg|TU-7 variant with five repetition rates
Tek tu-7 c2.jpg|TU-7 variant with five repetition rates

Revision as of 08:34, 4 February 2018

Template:Plugin Sidebar 2 The Tektronix TU-7/1M1/067-0521-00 is a letter series plug-in used for calibrating 500-series scopes.

It is a multifunction replacement for the Type P Pulser, the TU-2 Test Load, and the EP-53 Gain Set Adaptor.

It is used for calibrating the mainframe's step response and gain, checking dual-trace operation, common mode rejection, and power supply regulation.

(500-series mainframes are designed to have 10 div/Volt response to differential signals from the plug-in, and zero response to common-mode signals.)

It contains a transistor multivibrator whose output is sharpened through Tek-made Gallium-Arsenide diodes (later production used silicon), a dual-trace circuit using 12AT7 and 6AL5 tubes, and various load resistors. It does not have the Type P's short operating life because it does not use a mercury switch.

This instrument went through several names. At its 1964 introduction, it was the TU-7. Some early Tek-internal instruments for design, manufacturing, and calibration had TU (Test Unit) nomenclature. (Other examples include the TU-75B Variac, the TU-?? dim-bulb fixture, and the TU-50 sine/square/pulse generator.)

In 1965, it was renamed Type 1M1 to fit into the letter-series nomenclature like its predecessor. Later still, the 067- calibration fixture naming system took hold and it was rechristened 067-0521-00.

The instrument was also revised once - more pulse frequencies - and the name upgraded to 067-0521-01.

It does not appear - under any name - in any Tek catalog, but the 1964 catalog does list a cousin: Type 10/11M1, for the Type 647 scope.

Pictures

<gallery> 067-0521-00 1.JPG Tek 1m1 front.jpg Tek 1m1 right.jpg Tek 1m1 left.jpg Tek tu-7 c1.jpg|TU-7 variant with five repetition rates Tek tu-7 c2.jpg|TU-7 variant with five repetition rates Tek tu-7 c3.jpg|TU-7 variant with five repetition rates Tek tu-7 c4.jpg|TU-7 variant with five repetition rates Tek tu-7 c5.jpg|TU-7 variant with five repetition rates