7000 Series plug-in interface: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
 
(33 intermediate revisions by 5 users not shown)
Line 1: Line 1:
'''[[7000-series scopes|Tektronix 7000 series oscilloscope mainframes]]''' have one ([[7912]]) or two vertical plug-in slots, and zero ([[7612D]]), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.
'''[[7000-series scopes|Tektronix 7000 series oscilloscope mainframes]]''' have one ([[7912]]) or two vertical plug-in slots, and zero ([[7612D]]), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.


The interconnect on either slot type is a 76-pin PCB edge connector. The pinout on vertical and horizontal slots is not identical but
According to [[Barrie Gilbert]] in [https://ieeexplore.ieee.org/stamp/stamp.jsp?arnumber=4785651 ''The Gears of Genius''], the 7000 series backplane was largely developed by [[Les Larson]].
 
The interconnect on either slot type is a 76-pin, 0.1" pitch PCB edge connector. The pinout on vertical and horizontal slots is not identical but
compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may  
compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may  
be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.
be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.


Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the [[Media:Tek-7a17-left-board.jpg|plug-in PCB's component side]]) and "B" are on the right (on the [[Media:Tek-7a17-right-board.jpg|plugin PCB's solder side]]). Pins are numbered from 1 at the bottom to 38 on the top.  
Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the [[Media:Tek-7a17-left-board.jpg|plug-in PCB's component side]]) and "B" are on the right (on the [[Media:Tek-7a17-right-board.jpg|plug-in PCB's solder side]]). Pins are numbered from 1 at the bottom to 38 on the top.  
In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.
In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.


Line 15: Line 17:
|-
|-
!width="10%"| 
!width="10%"| 
!width="45%"| A side
!colspan="2"| A side
!width="45%"| B side
!colspan="2"| B side
|-
|-
! Pin  
! Pin  
! Function
! colspan="2" | Function
! Function
! colspan="2" | Function
|-  
|-  
|  1 || Sweep Gate (H)  || Delay mode ctl in (H-B)
|  1  
| colspan="2" | Sweep Gate (H)   
| colspan="2" | Delay mode ctl in (H-B)
|-  
|-  
|  2 || Gate common  || Delay mode ctl out (H-A)
|  2  
| colspan="2" | Gate common   
| colspan="2" | Delay mode ctl out (H-A)
|-  
|-  
|  3 || A Sweep (V & H-A) ''[note 1]''    || B Sweep (V & H-B) ''[note 1]''
|  3  
| colspan="2" | A Sweep (V & H-A) ''[note 1]''     
| colspan="2" | B Sweep (V & H-B) ''[note 1]''
|-  
|-  
|  4 || Line trigger || Trigger holdoff (H)
|  4  
| colspan="2" | Line trigger  
| colspan="2" | Trigger holdoff (H)
|-
|-
|  5 || Chop drive  || Aux Swp gate (H)
|  5  
| colspan="2" | Chop drive   
| colspan="2" | Aux Swp gate (H)
|-
|-
|  6 || Chop common  || ALT drive
|  6  
| colspan="2" | Chop common   
| colspan="2" | ALT drive
|-
|-
|  7 || Intensity Limit (H) || MF Channel Switch
|  7  
| colspan="2" | Intensity Limit (H)  
| colspan="2" | MF Channel Switch
|-
|-
|  8 || bgcolor="Pink"| +5 V  ||  Sweep inhibit (H)
|  8  
| colspan="2" bgcolor="Pink" | +5 V   
| colspan="2" |  Sweep inhibit (H)
|-
|-
|  9 || bgcolor="Pink"| +5 V (lights)  || Delay gate (H)
|  9  
| colspan="2" bgcolor="Pink" | +5 V (lights)   
| colspan="2" | Delay gate (H)
|-
|-
| 10 || Single sweep ready (H)  ||  X comp inhibit (H)
| 10  
| colspan="2" | Single sweep ready (H)   
| colspan="2" |  X comp inhibit (H)
|- bgcolor="Yellow"  
|- bgcolor="Yellow"  
| 11 || +Signal || −Signal
| 11  
| colspan="2" | +Signal  
| colspan="2" | −Signal
|- bgcolor="Pink"  
|- bgcolor="Pink"  
| 12 || Signal Ground || Signal Ground  
| 12  
| colspan="2" | Signal Ground  
| colspan="2" | Signal Ground  
|- bgcolor="Yellow"  
|- bgcolor="Yellow"  
| 13 || +Trigger (V) ''[note 2]'' ||  −Trigger (V) ''[note 2]''
| 13  
| colspan="2" | +Trigger (V) ''[note 2]''  
| colspan="2" |  −Trigger (V) ''[note 2]''
|-
|-
| 14 || bgcolor="Pink"| Lights common || Dual beam Aux Y-Axis  
| 14  
| colspan="2" bgcolor="Pink" | Lights common  
| colspan="2" | Dual beam Aux Y-Axis  
|-
|-
| 15 || Single sweep logic || Single sweep reset (H)
| 15  
| colspan="2" | Single sweep logic  
| colspan="2" | Single sweep reset (H)
|-
|-
| 16 || MF Mode  || Aux Y axis  (H)
| 16  
| colspan="2" | MF Mode   
| colspan="2" | Aux Y axis  (H)
|-
|-
| 17 || Aux Z axis  || Aux Z common  
| 17  
| colspan="2" | Aux Z axis   
| colspan="2" | Aux Z common  
|- bgcolor="Pink"
|- bgcolor="Pink"
| 18 || +15 V  || −15 V
| 18  
| colspan="2" | +15 V   
| colspan="2" | −15 V
|- bgcolor="Pink"
|- bgcolor="Pink"
| 19 || +50 V  || −50 V  
| 19  
| colspan="2" | +50 V   
| colspan="2" | −50 V  
|- bgcolor="Yellow"  
|- bgcolor="Yellow"  
| 20 || +Trigger in (H) || −Trigger in (H)
| 20  
| colspan="2" | +Trigger in (H)  
| colspan="2" | −Trigger in (H)
|- bgcolor="Yellow"  
|- bgcolor="Yellow"  
| 21 || +Aux trigger in (H) ''[note 5]''|| −Aux trigger in (H) ''[note 5]''
| 21  
| colspan="2" | +Aux trigger in (H) ''[note 5]''
| colspan="2" | −Aux trigger in (H) ''[note 5]''
|- bgcolor="LightBlue"  
|- bgcolor="LightBlue"  
| 22 || /EOI ''[note 6]'' || /SRQ ''[note 6]''
| 22  
| colspan="2" | /EOI ''[note 6]''  
| colspan="2" | /SRQ ''[note 7]''
|- bgcolor="LightBlue"  
|- bgcolor="LightBlue"  
| 23 || /DAV  || REN  
| 23  
| colspan="2" | /DAV   
| colspan="2" | REN  
|- bgcolor="LightBlue"  
|- bgcolor="LightBlue"  
| 24 || /IFC  ''[note 3]'' || /ATN
| 24  
| colspan="2" | /IFC  ''[note 3]''  
| colspan="2" | /ATN
|- bgcolor="LightBlue"  
|- bgcolor="LightBlue"  
| 25 || /NDAC || /NRFD
| 25  
| colspan="2" | /NDAC  
| colspan="2" | /NRFD
|- bgcolor="LightBlue"
|- bgcolor="LightBlue"
| 26 || Logic Common || /SND
| 26  
|- bgcolor="Pink"
| colspan="2" | Logic Common  
| 27 || −5.2 V ''[note 4]''|| 5.1 V ''[note 4]''
| colspan="2" | /SND <br />or Inter-plugin GND ''[note 8]''
|-  
| 27
| bgcolor="Pink" | −5.2 V<br />''[note 4]''  
| Inter-plugin<br />link
| bgcolor="Pink" | +5.1 V<br />''[note 4]''  
| Inter-plugin<br />link
|-
|-
| 28 || n.c. || n.c.
| 28  
| colspan="2" | Inter-plugin link
| colspan="2" | Inter-plugin link
|- bgcolor="LightGreen"
|- bgcolor="LightGreen"
| 29 || TS10  ''[note 3]'' || TS9 ''(DIO8)''
| 29  
|- bgcolor="LightGreen"
| colspan="2" | TS10  ''[note 3]''  
| 30 || TS8 ''(DIO7)''  || TS7 ''(DIO6)''
| bgcolor="LightGreen" | TS9  
|- bgcolor="LightGreen"
| bgcolor="LightBlue"  | ''DIO8''
| 31 || TS6 ''(DIO5)''  || TS5 ''(DIO4)''
|-  
|- bgcolor="LightGreen"
| 30
| 32 || TS4 ''(DIO3)''  || TS3 ''(DIO2)''
| bgcolor="LightGreen" | TS8
|- bgcolor="LightGreen"
| bgcolor="LightBlue"  | ''DIO7''   
| 33 || TS2 ''(DIO1)''  || TS1 ''[note 3]''
| bgcolor="LightGreen" | TS7
| bgcolor="LightBlue"  | ''DIO6''
|-  
| 31
| bgcolor="LightGreen" | TS6
| bgcolor="LightBlue"  | ''DIO5''   
| bgcolor="LightGreen" | TS5
| bgcolor="LightBlue"  | ''DIO4''
|-  
| 32
| bgcolor="LightGreen" | TS4
| bgcolor="LightBlue"  | ''DIO3''   
| bgcolor="LightGreen" | TS3
| bgcolor="LightBlue"  | ''DIO2''
|-  
| 33
| bgcolor="LightGreen" | TS2
| bgcolor="LightBlue"  | ''DIO1''   
| colspan="2" bgcolor="LightGreen" | TS1 ''[note 3]''
|-
|-
| 34 || n.c.  || n.c.  
| 34  
| colspan="2" | n.c.   
| colspan="2" | n.c.  
|-  
|-  
| 35 || bgcolor="LightGreen"| Force readout || Plugin mode ''[note 7]''
| 35  
| colspan="2" bgcolor="LightGreen" | Force readout  
| colspan="2" | Plugin mode ''[note 8]''
|-
|-
| 36 || n.c. || n.c.  
| 36  
| colspan="2" | n.c.  
| colspan="2" | n.c.  
|- bgcolor="LightGreen"
|- bgcolor="LightGreen"
| 37 || Ch. 1 Col  || Ch. 1 Row  
| 37  
| colspan="2" | Ch. 1 Col   
| colspan="2" | Ch. 1 Row  
|- bgcolor="LightGreen"
|- bgcolor="LightGreen"
| 38 || Ch. 2 Col  || Ch. 2 Row  
| 38  
| colspan="2" | Ch. 2 Col   
| colspan="2" | Ch. 2 Row  
|-
|-
|}
|}


===Pin group function legend===
===Pin group function legend===
:{| cellpadding="4"
{| cellpadding="4"
|-
|-
| bgcolor="Pink" | Plugin power
| bgcolor="Pink" | Plugin power
Line 109: Line 197:
| bgcolor="LightGreen" | [[7000 series readout system|Readout system]] signals
| bgcolor="LightGreen" | [[7000 series readout system|Readout system]] signals
|-
|-
| bgcolor="LightBlue"  | IEEE-488 bus used in [[7A16P]], [[7A29P]], [[7B90P]], digitizer mainframes; data 1-8 on TS2-TS9 lines
| bgcolor="LightBlue"  | IEEE-488 bus<br /> (used in [[7A16P]], [[7A29P]], [[7B90P]], digitizer mainframes
|}
|}
|
 
===Description of signals===
===Power Supply Load Limits===
* ''Sweep Gate'' − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected
According to the [[7A17]] manual, the total allowed DC power consumption for each plugin is 16.5 W, with individual current limits as shown below.
* ''Delay Mode Control'' − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B. >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function.  Grounded in amplifier plugins.
 
* ''A/B Sweep'' − 500 mV<sub>p-p</sub>, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins
:{| class="wikitable"
* ''Line Trigger'' − Approx. 1 V<sub>RMS</sub> mains-frequency signal from power supply (through transformer)
|-
* ''Trigger Holdoff'' − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing.
|-
* ''Chop Drive'' − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in.
! Supply Rail
* ''Aux Sweep Gate'' − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep
! Pin
* ''Alt Drive'' − 0/+5 V; high level will display channel 2 of a dual-trace plug-in. low will display channel 1.
! Maximum Current
* ''Intensity Limit'' − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT [[phosphor]]
|-  
* ''Mainframe Channel Switch'', ''Mainframe Mode'' − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR)
| +5 V || A8 || 500 mA
* ''Sweep Inhibit/Sweep Lockout'' - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing.
|-
* ''Delay Gate'' − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected. Grounded in amplifier plugins.
+15 V || A18  || 500 mA
* ''Single sweep ready'' − 0/+5 V, high when single sweep is ready
|-
* ''X comp. inhibit'' − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function ([[7904|7904 Opt.2]], [[7104|7104 Opt.2]])
|  −15 V || B18 || 500 mA
* ''Signal'' − Signal output from plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential).
|-
* ''Trigger'' − Copy of signal output from V plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots.
+50 V || A19 || 100 mA
* ''Dual Beam Aux Y-Axis'' − Used in dual beam mainframes ([[7844]]), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
|-
* ''Single Sweep Logic'' − 0/+5 V; high level when time-base is in single sweep mode.
|  −50 V || B19 || 100 mA
* ''Single Sweep Reset'' − Switched to ground to reset single sweep.
* ''Aux Y-Axis'' − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
* ''Aux Z Axis'' − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see MF Ch Switch above)
* ''Trigger In'' − Trigger signal input on H plugin, routed from V plugin's trigger output. Differential, 50 Ω per side, 50 mV/Div (differential).
* ''Aux Trigger In'' − Only used by [[7B52]]
* ''GPIB lines'' − Control signal functions are the same as their [[GPIB interface|IEEE-488 (GPIB)]] equivalents. Time slot lines 2 to 9 double as IEEE-488 data lines.
* ''TS1−TS10'' − [[7000 series readout system|readout system]] time slot pulses. Idle 0, active −15 V.
* ''Force Readout'' − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by many 7DXX plug-ins.
* ''Plugin Mode'' − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin.
* ''Ch1/2 Row/Col'' − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom. Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.
|}
|}


Line 148: Line 226:
''[note 2]'' Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots
''[note 2]'' Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots


''[note 3]'' In programmable mainframes, A24 is pulled high to +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, with TS1 being active in time slot 1 as in other mainframes, and TS10 being active in each time slot.
''[note 3]'' In programmable mainframes, A24 is clamped to not exceed +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, with TS1 being active in time slot 1 as in other mainframes, and TS10 being active in each time slot. Programmable plug-ins source at least 100 μA into TS10 (A29) indicating to a programmable mainframe that the alternative time-slot scheme is to be used.


''[note 4]'' Not provided by most mainframes (digitizers only?). [[7A16P]] connects B27 to A9, requires −5.2 V on A27.
''[note 4]'' Not provided by most mainframes (digitizers only?). [[7A16P]] connects B27 to A9, requires −5.2 V on A27.
Line 154: Line 232:
''[note 5]'' According to the [[Media:Tek 11000-series plug-in to main frame interface manual.pdf|11000-series interface manual]], ''many 7k plug-in units ground pin B21 or connect it to pin A21'', and ''The [[7D10]], [[7D11]], [[7D14]], [[7S14]], and possibly some others have pin A21 grounded''.
''[note 5]'' According to the [[Media:Tek 11000-series plug-in to main frame interface manual.pdf|11000-series interface manual]], ''many 7k plug-in units ground pin B21 or connect it to pin A21'', and ''The [[7D10]], [[7D11]], [[7D14]], [[7S14]], and possibly some others have pin A21 grounded''.


''[note 6]'' A22 = Busy output from [[7D12]], [[7D15]], B22 = /Hold input to 7D12, 7D15; no corresponding mainframe connections known
''[note 6]'' A22 = Busy output from [[7D12]], [[7D15]]; A22 = Delayed Sweep Gate output for [[7B53A]] with [[media:7B53A_MOD.pdf|mod. 769G]], routed to real panel on [[7403]] or [[7603]] scopes with 769H mod.


''[note 7]'' The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance):
''[note 7]'' B22 = /Hold input to 7D12, 7D15. Mainframe connection or use unclear.
 
''[note 8]'' The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance):
:{| class="wikitable"
:{| class="wikitable"
|-
|-
Line 164: Line 244:
! Voltage
! Voltage
|-  
|-  
| CH 1, Delaying, Intensified, Normal || ≥30 kΩ  || 5 V
| CH 1, Delaying, Intensified, Normal || ≥30 kΩ  || 5 V
|-
|-
| CH 2, Delayed Sweep || 3.9 kΩ || 4 V
| CH 2, Delayed Sweep || 3.9 kΩ || 4 V
Line 175: Line 255:
|}
|}


==Links==
[[Image:7000 slot pinout.jpg|thumb|400px|left]]
|
===Description of signals===
* ''Sweep Gate'' − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected.
* ''Delay Mode Control'' − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B.  >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function.  Grounded in amplifier plugins.
* ''A/B Sweep'' − 500 mV<sub>p-p</sub>, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins.
* ''Line Trigger'' − Approx. 3 V<sub>RMS</sub> mains-frequency signal from power supply (through transformer). ''Present on all slots.''
* ''Trigger Holdoff'' − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing.
* ''Chop Drive'' − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in.
* ''Aux Sweep Gate'' − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep. Used to deliver the realtime clock signal from [[7B87]] to [[7854]].
* ''Alt Drive'' − 0/+5 V; high level will display channel 2 of a dual-trace plug-in, low will display channel 1.
* ''Intensity Limit'' − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT [[phosphor]].
* ''Mainframe Channel Switch'' − −0.6/+1.1 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
* ''Mainframe Mode'' − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
* ''Sweep Inhibit/Sweep Lockout'' - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing and delayed sweep of the ''B'' time base.
* ''Delay Gate'' − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. Mainframes connect this signal from the ''A'' timebase through a 2 k resistor and a diode to B8 ''Sweep inhibit'' of the ''B'' time base to trigger the delayed sweep. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected.  Grounded in amplifier plugins.
* ''Single sweep ready'' − 0/+5 V, high when single sweep is ready.
* ''X comp. inhibit'' − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function ([[7503]], [[7504|7504 Opt.02]], [[7704|7704 Opt.02]], [[7904|7904 Opt.02]], [[7104|7104 Opt.02]]).
* ''Signal'' − Signal output from plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential).
* ''Trigger'' − Copy of signal output from V plugin to mainframe.  Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots.
* ''Dual Beam Aux Y-Axis'' − Used in dual beam mainframes ([[7844]]), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
* ''Single Sweep Logic'' − 0/+5 V; high level when time-base is in single sweep mode.
* ''Single Sweep Reset'' − Switched to ground to reset single sweep.
* ''Aux Y Axis'' − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity; driven only when plug-in output is displayed (see ''MF Ch Switch'' above).  Not available in early mainframes e.g. [[7504]], [[7704]] non-A.
* ''Aux Z Axis'' − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see ''MF Ch Switch'' above).
* ''Trigger In'' − Trigger signal input on H plugin, routed from V plugin's trigger output.  Differential, 50 Ω per side, 50 mV/Div (differential).
* ''Aux Trigger In'' − Provided by 1<sup>st</sup> generation 7000 series mainframes ([[7704]], [[7504]], [[7503]], [[7403N]]).  Only known use is in the [[7B52]] timebase as an optional source for the delayed trigger.  Four-bay mainframes supply the trigger signal from the left horizontal bay to Aux Trig In on the right horizontal bay and vice versa, via 510 Ω resistors.  Three-bay mainframes supply the Left Vert trigger signal via 510 Ω resistors.
* ''Inter-Plugin Connections'' − In 1<sup>st</sup> generation 7000 series mainframes ([[7704]], [[7504]], [[7503]], [[7403N]]), pins 26B, 27A/B and 28A/B are inter-plugin connections.  In the 3-bay mainframes, right vertical slot pins 27A, 27B, 28A, 28B are connected via 50 Ω striplines to horizontal slot pins 27B, 27A, 28B, 28A respectively, with ground on 26B.  Four-slot mainframes additionally make the same connections from the left vertical slot to the right horizontal slot.  ''More information needed - were any plug-ins made that used these?''
* ''GPIB lines'' − Control signal functions are the same as their [[GPIB interface|IEEE-488 (GPIB)]] equivalents.  Time slot lines 2 to 9 double as IEEE-488 data lines.
* ''TS1−TS10'' − [[7000 series readout system|readout system]] time slot pulses.  Idle 0, active −15 V.
* ''Force Readout'' − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by several 7DXX plug-ins.
* ''Plugin Mode'' − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin.
* ''Ch1/2 Row/Col'' − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom.  Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.
 


* [[Media:Tek 7000-series plug-in mainframe interface manual no ocr.pdf|Tektronix 7000-Series Plug-in to Mainframe Interface Manual (PDF, needs OCR)]]
|}


==Links==
* [[Repairing 7000-series plug-in sockets]]
* [[Media:Tek 7000-series plug-in mainframe interface manual ocr.pdf|Tektronix 7000-Series Plug-in to Mainframe Interface Manual (PDF)]]
* [[Media:Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970).pdf| Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970)]] (PDF,OCR,1MB)
* [[Media:Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970).pdf| Introduction to the 7000 Series Switching and Logic Circuits (Ken Parker, 1970)]] (PDF,OCR,1MB)
* [https://archive.org/details/tektronix_7000_backplane_Pin_Out Kahrs, ''Interfacing to the Tektronix 7000 series'']
* [https://archive.org/details/tektronix_7000_backplane_Pin_Out Kahrs, ''Interfacing to the Tektronix 7000 series'']
* [[067-0589-00|067-0589-00 rigid extender]]
* [[067-0616-00|067-0616-00 flexible extender]]
* [https://www.ecosensory.com/tek/tek_7K_flex_sales_blurb.txt John Griessen's flex extender kit] / [https://www.ecosensory.com/tek/TEK_7K_FLEX_assy-013-sm.jpg Photo]
==Prototype==
After it was decided that there would be a "New Generation" series of lab scopes to replace the [[500-series scopes|500 series]], concept prototypes were built.
Before [[Howard Vollum]] decided on the height of the New Generation plug-ins, a taller form factor was being considered. This is what it looked like:
<gallery>
Tek 7k concept plug-in pre-prototype 1.jpg|Very Early New Generation Plug-in Prototype
Tek 7k concept plug-in pre-prototype 2.jpg|Very Early New Generation Plug-in Prototype
Tek 7k concept plug-in pre-prototype 3.jpg|Very Early New Generation Plug-in Prototype
Tek 7k concept plug-in pre-prototype 4.jpg|Very Early New Generation Plug-in Prototype
</gallery>
From [[Media:On-The-History-And-Environment-Of-Tektronix.pdf|On the History and Environment of Tektronix]] page 58:
<blockquote>
But [[Howard Vollum|Howard]] then threw another challenge to his group: plug-in height.
Work up through late 1966 had assumed a seven inch plug-in height which would provide room for the needed components using readily available and proven parts.
But the H-P scopes were smaller in size and quite attractive in appearance.
So, one day, Howard said, "the plug-ins will be 5 1/2 inches in height."


[[Oliver Dalton]] recalls the decision to reduce the plug-in height as a traumatic one:
"The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the [[7000 series readout system|IC read-out effort]]: 1) new [[Back-lit switches|lit push-buttons]] ... we needed 25 on a panel; 2) [[cam switch]]es - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) [[Miniature relays|relays]] ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers."
</blockquote>


[[Image:7000 slot pinout.jpg|thumb|500px|left]]


[[Category:Plug-in interfaces]]
[[Category:Plug-in interfaces]]

Latest revision as of 15:21, 8 March 2024

Tektronix 7000 series oscilloscope mainframes have one (7912) or two vertical plug-in slots, and zero (7612D), one (7xx3, 7912) or two (7xx4) horizontal plug-in slots.

According to Barrie Gilbert in The Gears of Genius, the 7000 series backplane was largely developed by Les Larson.

The interconnect on either slot type is a 76-pin, 0.1" pitch PCB edge connector. The pinout on vertical and horizontal slots is not identical but compatible to the point that vertical plugins can be installed in horizontal slots and vice versa. However, in that case, some functions may be unavailable − for example, trigger signals are only routed to H slots so a timebase in a V slot must be externally triggered.

Looking into the mainframe from the front panel, "A" pins are left of the connector centerline (on the plug-in PCB's component side) and "B" are on the right (on the plug-in PCB's solder side). Pins are numbered from 1 at the bottom to 38 on the top. In the following table, (H) indicates signals available in horizontal slots only, (H-A) is horizontal slot A, (H-B) is horizontal slot B, and (V) denotes signals available in vertical slots only.

  A side B side
Pin Function Function
1 Sweep Gate (H) Delay mode ctl in (H-B)
2 Gate common Delay mode ctl out (H-A)
3 A Sweep (V & H-A) [note 1] B Sweep (V & H-B) [note 1]
4 Line trigger Trigger holdoff (H)
5 Chop drive Aux Swp gate (H)
6 Chop common ALT drive
7 Intensity Limit (H) MF Channel Switch
8 +5 V Sweep inhibit (H)
9 +5 V (lights) Delay gate (H)
10 Single sweep ready (H) X comp inhibit (H)
11 +Signal −Signal
12 Signal Ground Signal Ground
13 +Trigger (V) [note 2] −Trigger (V) [note 2]
14 Lights common Dual beam Aux Y-Axis
15 Single sweep logic Single sweep reset (H)
16 MF Mode Aux Y axis (H)
17 Aux Z axis Aux Z common
18 +15 V −15 V
19 +50 V −50 V
20 +Trigger in (H) −Trigger in (H)
21 +Aux trigger in (H) [note 5] −Aux trigger in (H) [note 5]
22 /EOI [note 6] /SRQ [note 7]
23 /DAV REN
24 /IFC [note 3] /ATN
25 /NDAC /NRFD
26 Logic Common /SND
or Inter-plugin GND [note 8]
27 −5.2 V
[note 4]
Inter-plugin
link
+5.1 V
[note 4]
Inter-plugin
link
28 Inter-plugin link Inter-plugin link
29 TS10 [note 3] TS9 DIO8
30 TS8 DIO7 TS7 DIO6
31 TS6 DIO5 TS5 DIO4
32 TS4 DIO3 TS3 DIO2
33 TS2 DIO1 TS1 [note 3]
34 n.c. n.c.
35 Force readout Plugin mode [note 8]
36 n.c. n.c.
37 Ch. 1 Col Ch. 1 Row
38 Ch. 2 Col Ch. 2 Row

Pin group function legend

Plugin power
HF signals
Readout system signals
IEEE-488 bus
 (used in 7A16P, 7A29P, 7B90P, digitizer mainframes) 

Power Supply Load Limits

According to the 7A17 manual, the total allowed DC power consumption for each plugin is 16.5 W, with individual current limits as shown below.

Supply Rail Pin Maximum Current
+5 V A8 500 mA
+15 V A18 500 mA
−15 V B18 500 mA
+50 V A19 100 mA
−50 V B19 100 mA

Notes

[note 1] Output from H plugins, input on V plugins

[note 2] Output from V plugins, unused and terminated 50 Ω to ground in mainframe H slots

[note 3] In programmable mainframes, A24 is clamped to not exceed +3 V, indicating to programmable plug-ins to use TS2-TS9 as GPIB lines and a modified readout logic using only TS1 and TS10, with TS1 being active in time slot 1 as in other mainframes, and TS10 being active in each time slot. Programmable plug-ins source at least 100 μA into TS10 (A29) indicating to a programmable mainframe that the alternative time-slot scheme is to be used.

[note 4] Not provided by most mainframes (digitizers only?). 7A16P connects B27 to A9, requires −5.2 V on A27.

[note 5] According to the 11000-series interface manual, many 7k plug-in units ground pin B21 or connect it to pin A21, and The 7D10, 7D11, 7D14, 7S14, and possibly some others have pin A21 grounded.

[note 6] A22 = Busy output from 7D12, 7D15; A22 = Delayed Sweep Gate output for 7B53A with mod. 769G, routed to real panel on 7403 or 7603 scopes with 769H mod.

[note 7] B22 = /Hold input to 7D12, 7D15. Mainframe connection or use unclear.

[note 8] The plug-in mode is supplied to the mainframe either as a resistor connected to ground (with 5% tolerance), or by supplying a DC voltage (with 0.25 V tolerance):

Plugin Mode Resistance Voltage
CH 1, Delaying, Intensified, Normal ≥30 kΩ 5 V
CH 2, Delayed Sweep 3.9 kΩ 4 V
ADD, Mixed Sweep 620 Ω 2 V
ALT 240 Ω 1 V
Chop 0-47 Ω 0 V

Description of signals

  • Sweep Gate − 0/+5 V, high while sweep is running (beam unblanking), connected to +5 V in amplifier plugins; +Gate Output on mainframe uses Sweep Gate from H slot A when A Gate is selected, and from H slot B when B is selected.
  • Delay Mode Control − Output on delaying timebase in horizontal slot A, connected to input on delayed timebase in horizontal slot B. >+3 V disables auto sweep in delayed timebase; 0 V enables independent timebase function. Grounded in amplifier plugins.
  • A/B Sweep − 500 mVp-p, negative-going copy of sweep signal from timebase, not affected by X position control or magnifier; Used for mainframe's Sawtooth Out, additionally fed to V plugins.
  • Line Trigger − Approx. 3 VRMS mains-frequency signal from power supply (through transformer). Present on all slots.
  • Trigger Holdoff − 0/+5 V, generated by time-base, high during holdoff time of time-base, used in mainframe for ALT sequencing.
  • Chop Drive − 0/+5 V; switches at one-half the rate of the VERTICAL MODE CHOP signal; high level selects channel 2, low level selects channel 1 of a dual-trace plug-in.
  • Aux Sweep Gate − 0/+5 V; pulled high by dual-sweep time-base plug-ins during auxiliary sweep. Used to deliver the realtime clock signal from 7B87 to 7854.
  • Alt Drive − 0/+5 V; high level will display channel 2 of a dual-trace plug-in, low will display channel 1.
  • Intensity Limit − Switched to ground by timebase in slow sweep speeds (≥100 ms/Div), limits beam intensity to protect the CRT phosphor.
  • Mainframe Channel Switch − −0.6/+1.1 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
  • Mainframe Mode − 0/+5 V logic levels; plug-in output is displayed when MF Channel Switch ≠ MF Mode (XOR).
  • Sweep Inhibit/Sweep Lockout - Mainframe injects current > 1 mA to prevent time base from sweeping. Used for ALT sequencing and delayed sweep of the B time base.
  • Delay Gate − negative-going pulse starting at the end of the delay period, and lasting until the end of the sweep from the delaying timebase. Mainframes connect this signal from the A timebase through a 2 k resistor and a diode to B8 Sweep inhibit of the B time base to trigger the delayed sweep. +Gate Output on mainframe uses Delay Gate from H slot B when Delay Gate is selected. Grounded in amplifier plugins.
  • Single sweep ready − 0/+5 V, high when single sweep is ready.
  • X comp. inhibit − Connected to ground in amplifiers, switched to ground by timebase set to amplifier (X-Y) mode to enable X-Y delay compensation in scopes with that function (7503, 7504 Opt.02, 7704 Opt.02, 7904 Opt.02, 7104 Opt.02).
  • Signal − Signal output from plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential).
  • Trigger − Copy of signal output from V plugin to mainframe. Differential, 50 Ω per side. 50 mV/Div (differential). Terminated on H slots.
  • Dual Beam Aux Y-Axis − Used in dual beam mainframes (7844), Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity.
  • Single Sweep Logic − 0/+5 V; high level when time-base is in single sweep mode.
  • Single Sweep Reset − Switched to ground to reset single sweep.
  • Aux Y Axis − Current-driven input to mainframe allowing vertical separation of two traces with dual timebase plugins. 1 mA/Div sensitivity; driven only when plug-in output is displayed (see MF Ch Switch above). Not available in early mainframes e.g. 7504, 7704 non-A.
  • Aux Z Axis − Current-driven input to mainframe allowing plugins to modulate beam intensity, e.g. in dual timebase A intensified by B display mode; driven only when plug-in output is displayed (see MF Ch Switch above).
  • Trigger In − Trigger signal input on H plugin, routed from V plugin's trigger output. Differential, 50 Ω per side, 50 mV/Div (differential).
  • Aux Trigger In − Provided by 1st generation 7000 series mainframes (7704, 7504, 7503, 7403N). Only known use is in the 7B52 timebase as an optional source for the delayed trigger. Four-bay mainframes supply the trigger signal from the left horizontal bay to Aux Trig In on the right horizontal bay and vice versa, via 510 Ω resistors. Three-bay mainframes supply the Left Vert trigger signal via 510 Ω resistors.
  • Inter-Plugin Connections − In 1st generation 7000 series mainframes (7704, 7504, 7503, 7403N), pins 26B, 27A/B and 28A/B are inter-plugin connections. In the 3-bay mainframes, right vertical slot pins 27A, 27B, 28A, 28B are connected via 50 Ω striplines to horizontal slot pins 27B, 27A, 28B, 28A respectively, with ground on 26B. Four-slot mainframes additionally make the same connections from the left vertical slot to the right horizontal slot. More information needed - were any plug-ins made that used these?
  • GPIB lines − Control signal functions are the same as their IEEE-488 (GPIB) equivalents. Time slot lines 2 to 9 double as IEEE-488 data lines.
  • TS1−TS10readout system time slot pulses. Idle 0, active −15 V.
  • Force Readout − Allows plug-in readout information to be displayed regardless of the mainframe mode switch setting when pulled low (<0.5 V). Used by several 7DXX plug-ins.
  • Plugin Mode − 5-level signal providing the mainframe with information about the operating mode of a dual-trace or dual-sweep plugin.
  • Ch1/2 Row/Col − Analog current inputs to the readout system. Ch1 refers to the first channel within the plugin slot in question and is associated with the readout field on top of the screen. Ch2 is the 2nd channel displayed at the bottom. Row/Current signals accept negative currents in 100 μA steps; typically, plugins contain resistors from time slot signal lines to row/current lines.


Links

Prototype

After it was decided that there would be a "New Generation" series of lab scopes to replace the 500 series, concept prototypes were built. Before Howard Vollum decided on the height of the New Generation plug-ins, a taller form factor was being considered. This is what it looked like:

From On the History and Environment of Tektronix page 58:

But Howard then threw another challenge to his group: plug-in height. Work up through late 1966 had assumed a seven inch plug-in height which would provide room for the needed components using readily available and proven parts. But the H-P scopes were smaller in size and quite attractive in appearance. So, one day, Howard said, "the plug-ins will be 5 1/2 inches in height."

Oliver Dalton recalls the decision to reduce the plug-in height as a traumatic one: "The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the IC read-out effort: 1) new lit push-buttons ... we needed 25 on a panel; 2) cam switches - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) relays ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers."