Cam switches: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(17 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Cam switches are used in many Tek instruments, particularly in [[7000-series plug-ins]], but also in [[TM500]] equipment and 400-series portable scopes.
'''Cam switches''' are used in many Tek instruments from the late 1960s to the early 1990s, particularly in [[7000-series plug-ins]], but also in [[TM500]] equipment and 400-series portable scopes.


The lobes on the rotary cam encode the lookup table of which contacts should be open or closed in each rotational position of the shaft,
The lobes on the rotary cam encode the lookup table of which contacts should be open or closed in each rotational position of the shaft,
Line 5: Line 5:
A benefit of this design is low parasitics compared to traditional rotary wafer switches.
A benefit of this design is low parasitics compared to traditional rotary wafer switches.


For cleaning, Tek recommends swiping paper soaked in isopropyl alcohol between the contacts and pads.
The original idea for this switch type is credited to [[Howard Vollum]] - see [[Patent US 3562464A|Patent 3,562,464 ''Cam actuated switch having movable and fixed contacts on circuit board'']] (Vollum, Verhoef, Sprando).  [[Ken Holland]] was also involved with the development of cam switches at Tek.
 
From ''[https://vintagetek.org/wp-content/uploads/2019/06/On-The-History-And-Environment-Of-Tektronix.pdf On The History and Environment of Tektronix]'':
<blockquote>
So, one day, Howard said, "the plug-ins will be 5¼ inches in height."
 
[[Oliver Dalton]] recalls the decision to reduce the plug-in height as a traumatic one:
"The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the [[7000 series readout system|IC read-out effort]]: 1) [[back-lit switches|new lit push-buttons]] ... we needed 25 on a panel; 2) cam switches - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) [[miniature relays|relays]] ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers.
 
[...]
 
Then Howard Vollum made the decision that Tek would develop its own switches, and [[Tony Sprando]], [[Bill Verhoef]], and Howard jointly developed the cam switch. The design ideas emerged from a "a lot of way-out brainstroming. "Howard played a key role by taking an "unlimited funds, the sky's the limit" attitude, while the other members would bring the ideas back to reality.
 
Once the concepts were established, the manufacturing problems began. The prototypes had been made on numerically controlled machines, and the proposal was now to cast key pieces in plastic. But the Plastics Group said it could not be done. Finally, Tony came up with a four-piece die design that would do the job (previous approaches to die design had assumed there would be only two pieces). The four-piece die was the critical breakthrough which then made production possible at a reasonable cost.
</blockquote>
 
There were different forms of contact fingers in use.
The basic type, as described in the patent drawings (also in use in the [[back-lit switches|back-lit pushbuttons]]) have a contact spring on a post soldered into the board.
Another type, used in high-frequency attenuators types, has a spring riveted to the board, with a small multi-fingered, gold-plated contact spring element isolated by a molded plastic assembly.  In these, the spring is typically grounded, and the isolated contact fingers bridge adjacent pads when actuated.
Some switch assemblies also have contacts on the opposite side of the PCB, actuated via small plastic plungers.
Finally, the [[067-0587-02]] plug-in uses a special [[Media:7104_maintenance.pdf|elastomer-based cam switch]].


==Maintenance==
==Maintenance==
* [http://hakanh.com/dl/docs/kitinstructions/040-0541-00.pdf 040-0541-00: Cam switch repair kit (1970)]
* For cleaning, Tek recommends swiping paper soaked in isopropyl alcohol between the contacts and pads.
* [[040-0541-00|040-0541-00 Cam switch repair kit]] (1970)
* [[Media:Tekscope 1977 V9 N1.pdf | TekScope Vol. 9 No. 1, 1977]] p.14: Cam switch cleaning tips
* [[Media:Tekscope 1977 V9 N1.pdf | TekScope Vol. 9 No. 1, 1977]] p.14: Cam switch cleaning tips
* [[Media:Tek cam switch repair manual.pdf|Tektronix cam switch repair manual]]


==Pictures==
==Pictures==
'''Drawings'''
<gallery>
Cam switch core.png              | Core of the cam switch
Basic cam switch contact.png    | Basic switch contact with solder post (shown in alignment jig)
Isolated cam switch contact.png  | Isolated contact type used in attenuators
Elastomer cam switch contact.png | Elastomer contact used in [[067-0587-02]]
</gallery>
'''Photos'''
<gallery>
<gallery>
Tek 7a19 frontright.jpg | Cam switch in [[7A19]]
Tek 7a19 frontright.jpg | Cam switch in [[7A19]]
Tek 7a19 rearright.jpg | Cam switch in [[7A19]]
Tek 7a19 rearright.jpg | Cam switch in [[7A19]]
Tek 7a19 att sw3.jpg | Cam switch in [[7A19]], contact fingers (isolated from spring lever)
Tek 7a19 att sw3.jpg   | Cam switch in [[7A19]] showing isolated contact fingers
Cam-01.jpg | Cam switch with contacts on both sides of the PCB ([[7D15]])
Cam-01.jpg | Cam switch with contacts on both sides of the PCB ([[7D15]])
Cam-02.jpg | 7D15 double-sided switch
Cam-02.jpg | 7D15 double-sided switch

Latest revision as of 14:57, 30 January 2024

Cam switches are used in many Tek instruments from the late 1960s to the early 1990s, particularly in 7000-series plug-ins, but also in TM500 equipment and 400-series portable scopes.

The lobes on the rotary cam encode the lookup table of which contacts should be open or closed in each rotational position of the shaft, which is typically rotated by a knob on the front panel of the instrument. A benefit of this design is low parasitics compared to traditional rotary wafer switches.

The original idea for this switch type is credited to Howard Vollum - see Patent 3,562,464 Cam actuated switch having movable and fixed contacts on circuit board (Vollum, Verhoef, Sprando). Ken Holland was also involved with the development of cam switches at Tek.

From On The History and Environment of Tektronix:

So, one day, Howard said, "the plug-ins will be 5¼ inches in height."

Oliver Dalton recalls the decision to reduce the plug-in height as a traumatic one: "The decision set us back at least one year for the height decision required three major electro-mechanical component efforts in addition to the IC read-out effort: 1) new lit push-buttons ... we needed 25 on a panel; 2) cam switches - these were Howard's ideas ... we needed them to be small and reasonably cheap; 3) relays ... we needed them to be small and reliable. We then largely had to make do with other available parts, like potentiometers.

[...]

Then Howard Vollum made the decision that Tek would develop its own switches, and Tony Sprando, Bill Verhoef, and Howard jointly developed the cam switch. The design ideas emerged from a "a lot of way-out brainstroming. "Howard played a key role by taking an "unlimited funds, the sky's the limit" attitude, while the other members would bring the ideas back to reality.

Once the concepts were established, the manufacturing problems began. The prototypes had been made on numerically controlled machines, and the proposal was now to cast key pieces in plastic. But the Plastics Group said it could not be done. Finally, Tony came up with a four-piece die design that would do the job (previous approaches to die design had assumed there would be only two pieces). The four-piece die was the critical breakthrough which then made production possible at a reasonable cost.

There were different forms of contact fingers in use. The basic type, as described in the patent drawings (also in use in the back-lit pushbuttons) have a contact spring on a post soldered into the board. Another type, used in high-frequency attenuators types, has a spring riveted to the board, with a small multi-fingered, gold-plated contact spring element isolated by a molded plastic assembly. In these, the spring is typically grounded, and the isolated contact fingers bridge adjacent pads when actuated. Some switch assemblies also have contacts on the opposite side of the PCB, actuated via small plastic plungers. Finally, the 067-0587-02 plug-in uses a special elastomer-based cam switch.

Maintenance

Pictures

Drawings

Photos