Ceramic strips: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 13: Line 13:
This can be avoided by keeping the HV circuit clean, particularly the nodes after the rectifier(s).
This can be avoided by keeping the HV circuit clean, particularly the nodes after the rectifier(s).


Tektronix warned that these strips should only be soldered with silver-bearing solder (3% AG was recommended) because
Tektronix warned that these strips should only be soldered with silver-bearing solder (3% Ag was recommended).
From [[502]] manual [[Media:070-090.pdf|070-090]] (1959), page 5-2:
 
<blockquote>
<blockquote>
«Repeated soldering with ordinary solder may weaken the silver-to-ceramic bond.»
'''Soldering Precautions'''
 
In the production of Tektronix instruments, a special silver-bearing solder is used to establish
a bond to the ceramic terminal strips. This bond may be broken by repeated use of ordinary tin-lead
solder, or by the application of too much heat. However, occasional use of ordinary solder will not
break the bond if too much heat is not applied.
 
It is advisable that you have a stock of solder containing about 3% silver if you frequently perform
work on Tektronix instruments. This type of solder is used quite often in printed circuitry and
should be readily available. It may also be purchased directly from Tektronix in one-pound rolls
(order by part number 251-514).
 
Because of the shape of the terminals on the ceramic terminal strips you may wish to use a
wedge-shaped tip on your soldering iron. A tip such as this allows you to apply heat directly to
the solder in the terminals thereby reducing the heat required to melt the solder. Since excessive
heat can destroy the bond of the terminal to the ceramic material, it is important to use as little
heat as possible. Also, the wedge-shaped tip is desirable from a convenience stand-point, since
it is easier to work on the ceramic strips with this type of tip.
</blockquote>
</blockquote>
Early instruments often contained a small spool of suitable solder inside the cabinet.
Early instruments often contained a small spool of suitable solder inside the cabinet.


Today, some solder types containing silver, e.g. Sn62Pb36Ag2, are still available.
Today, some suitable solder types containing silver, e.g. Sn62Pb36Ag2 (2% silver content, 179°C melting point), are still available.


Competitors like [[Lavoie]] used less sensitive tin-plated steel inserts that can be soldered with ordinary solder.
Competitors like [[Lavoie]] used less sensitive tin-plated steel inserts that can be soldered with ordinary solder.

Revision as of 06:17, 13 November 2019

Some Tektronix instruments use ceramic strips with metallized grooves to hold components and wiring. This started with the Type 315 in 1952. It continued into the early 7000-series instruments such as the 7514 mainframe and 7A18 vertical plug-in, both of which were introduced in 1971.

The production method is discussed in US Patent #3,121,020. The ceramic strips have turned out to be quite reliable. If they aren't abused, the only known failure mode is when they are used in HV supplies and are allowed to get very dirty. The dirt can become conductive, resulting in unintended current flow over the surface of the ceramic strip, and/or arcing. This can be avoided by keeping the HV circuit clean, particularly the nodes after the rectifier(s).

Tektronix warned that these strips should only be soldered with silver-bearing solder (3% Ag was recommended). From 502 manual 070-090 (1959), page 5-2:

Soldering Precautions

In the production of Tektronix instruments, a special silver-bearing solder is used to establish a bond to the ceramic terminal strips. This bond may be broken by repeated use of ordinary tin-lead solder, or by the application of too much heat. However, occasional use of ordinary solder will not break the bond if too much heat is not applied.

It is advisable that you have a stock of solder containing about 3% silver if you frequently perform work on Tektronix instruments. This type of solder is used quite often in printed circuitry and should be readily available. It may also be purchased directly from Tektronix in one-pound rolls (order by part number 251-514).

Because of the shape of the terminals on the ceramic terminal strips you may wish to use a wedge-shaped tip on your soldering iron. A tip such as this allows you to apply heat directly to the solder in the terminals thereby reducing the heat required to melt the solder. Since excessive heat can destroy the bond of the terminal to the ceramic material, it is important to use as little heat as possible. Also, the wedge-shaped tip is desirable from a convenience stand-point, since it is easier to work on the ceramic strips with this type of tip.

Early instruments often contained a small spool of suitable solder inside the cabinet.

Today, some suitable solder types containing silver, e.g. Sn62Pb36Ag2 (2% silver content, 179°C melting point), are still available.

Competitors like Lavoie used less sensitive tin-plated steel inserts that can be soldered with ordinary solder.

Links

Pictures