Difference between revisions of "P64xx input leads"

From TekWiki
Jump to: navigation, search
(Created page with "Logic probes from the '''Tektronix P64xx series''' share a common 10-lead input connector layout. These probes include the P6406, P6407, P6408, P6451, [[P6462]...")
 
 
(13 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
Logic probes from the '''Tektronix P64xx series''' share a common 10-lead input connector layout.
 
Logic probes from the '''Tektronix P64xx series''' share a common 10-lead input connector layout.
These probes include the [[P6406]], [[P6407]], [[P6408]], [[P6451]], [[P6462]], and possibly others.
+
 
 +
These probes include the [[P6406]], [[P6407]], [[P6408]], [[P6450]], [[P6451]], [[P6452]], [[P6455]], [[P6460]], [[P6462]], [[A6701]] and possibly others.
  
 
Original input lead sets were
 
Original input lead sets were
  
* 012-0747-00 - standard 10-wire 10 in/25 cm with pluggable probe tips
+
* 012-0747-00 standard 10-wire 10 in/25 cm with pluggable probe tips
* 012-0989-00 - 10-wire 5 in/12 cm with pluggable probe tips
+
* 012-0989-00 10-wire 5 in/12 cm with pluggable probe tips
* 012-0655-01 - ten individual 40 cm leads
+
* 012-0655-01 ten individual 40 cm leads
* 012-0655-02 - ten individual 8 cm leads
+
* 012-0655-02 ten individual 8 cm leads
* 012-0670-00 - ten individual 16 cm leads
+
* 012-0670-00 ten individual 16 cm leads
* 012-0800-00 - 10-wire 10 cm  
+
* 012-0800-00 10-wire 10 cm  
 +
* 012-0556-00 − diagnostic leads to connect [[P6460]] to diagnostic test points and test pattern generator outputs of [[1240]]/[[1241]] logic analyzers
 +
* [[103-0209-00]] - 2 x ten bundled leads connecting to a standard [[GPIB connector]] ,to be used with two probes. Supplied with the [[DF2]]
  
As the the probe-side input connector is a standard .65 mm square pin header on a 0.2" (5.08 mm) pitch,
+
As the probe-side input connector is a standard .65 mm square pin header on a 0.2" (5.08 mm) pitch,
 
it is also possible to use standard jumper wires with pins, sockets or clips on the other end for connecting inputs.
 
it is also possible to use standard jumper wires with pins, sockets or clips on the other end for connecting inputs.
 
+
==Instructions==
 +
* [[Media:012-0556-00.pdf |(012-0556-00) Instructions for diagnostics leads (PDF)]]
 +
==Pictures==
 
<gallery>
 
<gallery>
 
P6408 1.jpg      | [[P6408]] with 012-0747-00 harness and clips
 
P6408 1.jpg      | [[P6408]] with 012-0747-00 harness and clips
 
P64xx-jumper.jpg | Using P64xx probes with jumper wires
 
P64xx-jumper.jpg | Using P64xx probes with jumper wires
 
</gallery>
 
</gallery>
 +
 +
 +
[[Category:Cables]]
 +
[[Category:Logic analyzer probes]]

Latest revision as of 13:27, 12 April 2019

Logic probes from the Tektronix P64xx series share a common 10-lead input connector layout.

These probes include the P6406, P6407, P6408, P6450, P6451, P6452, P6455, P6460, P6462, A6701 and possibly others.

Original input lead sets were

  • 012-0747-00 − standard 10-wire 10 in/25 cm with pluggable probe tips
  • 012-0989-00 − 10-wire 5 in/12 cm with pluggable probe tips
  • 012-0655-01 − ten individual 40 cm leads
  • 012-0655-02 − ten individual 8 cm leads
  • 012-0670-00 − ten individual 16 cm leads
  • 012-0800-00 − 10-wire 10 cm
  • 012-0556-00 − diagnostic leads to connect P6460 to diagnostic test points and test pattern generator outputs of 1240/1241 logic analyzers
  • 103-0209-00 - 2 x ten bundled leads connecting to a standard GPIB connector ,to be used with two probes. Supplied with the DF2

As the probe-side input connector is a standard .65 mm square pin header on a 0.2" (5.08 mm) pitch, it is also possible to use standard jumper wires with pins, sockets or clips on the other end for connecting inputs.

Instructions

Pictures