S-1: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
(2 intermediate revisions by one other user not shown)
Line 19: Line 19:
{{Spec | Rise time | 350 ps }}
{{Spec | Rise time | 350 ps }}
{{Spec | Bandwidth | 1 GHz }}
{{Spec | Bandwidth | 1 GHz }}
{{Spec | Input amplitude | -1 V to +1 V  with ≤1 V<sub>p-p</sub> signals }}
{{Spec | Input amplitude | −1 V to +1 V  with ≤1 V<sub>p-p</sub> signals }}
{{Spec | Maximum input  | ±5 V<sub>DC</sub> or sine of 10 V<sub>p-p</sub> up to 10 MHz }}
{{Spec | Maximum input  | ±5 V<sub>DC</sub> or sine of 10 V<sub>p-p</sub> up to 10 MHz }}
{{Spec | Input impedance | 50 Ω  ([[GR-874]]) }}
{{Spec | Input impedance | 50 Ω  ([[GR-874]]) }}
Line 31: Line 31:
==Internals==
==Internals==
The S-1 uses a two-diode sampling gate which has relatively high "kick-out" (leakage of the strobe signal out of the input).   
The S-1 uses a two-diode sampling gate which has relatively high "kick-out" (leakage of the strobe signal out of the input).   
The manual cautions,
The manual cautions,
<blockquote>
<blockquote>
Line 38: Line 39:
bridge while the bridge is conducting.
bridge while the bridge is conducting.
</blockquote>
</blockquote>
The sampling bridge strobe signal is generated by an [[avalanche transistor]] followed by a [[step recovery diode]].


==Pictures==
==Pictures==
Line 51: Line 54:
S-52_s-1_rt_brighter.jpg | S-1 in a [[3S2]] sampler / [[567]] scope
S-52_s-1_rt_brighter.jpg | S-1 in a [[3S2]] sampler / [[567]] scope
Tek s1 sampler schematic.png|Tektronix S-1 sampler
Tek s1 sampler schematic.png|Tektronix S-1 sampler
Tek 7s11 s-1.jpg|[[7S11]] with S-1
</gallery>
</gallery>



Revision as of 14:27, 25 November 2018

Template:Plugin Sidebar 2

The S-1 sampling plug-in head provides a single GR-874 50 Ω input with a 350 ps rise-time.

The S-1 can be used with the 7000 series of sampling plug-ins, as well as the 3S series of sampling units.

Key Specifications

Rise time 350 ps
Bandwidth 1 GHz
Input amplitude −1 V to +1 V with ≤1 Vp-p signals
Maximum input ±5 VDC or sine of 10 Vp-p up to 10 MHz
Input impedance 50 Ω (GR-874)
Noise < 2 mV
Features trigger pickoff for internal triggering

Links

Internals

The S-1 uses a two-diode sampling gate which has relatively high "kick-out" (leakage of the strobe signal out of the input).

The manual cautions,

Operating the sampling head without the input connector terminated by a 50 Ω resistor or coaxial cable will cause a vertical shift of the zero signal baseline by a few millivolts. This is caused by the strobe kickout signal being reflected from the open input connector, and orriving bock at the sampling bridge while the bridge is conducting.

The sampling bridge strobe signal is generated by an avalanche transistor followed by a step recovery diode.

Pictures