S-4: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
 
(18 intermediate revisions by 5 users not shown)
Line 1: Line 1:
{{Plugin Sidebar 2 |
{{Plugin Sidebar
title=Tektronix S-4 |
|manufacturer=Tektronix
summary=Sampling Head |
|series=7000 and 3S series sampling heads
image=Tek-s-4.jpg |
|type=S-4
caption=S-4 head |
|summary=Sampling Head
series={{3S+7S}} |
|image=Tek-s-4.jpg
introduced=1968 |
|caption=S-4 head
discontinued=1990 |
|introduced=1968
manuals=
|discontinued=1990
* [http://w140.com/tek_s4.pdf Tektronix S-4 Manual, copyright 1969 (PDF)]
|designers=George Frye
* [http://w140.com/tek_S4_1985.pdf Tektronix S-4 Manual, revised 1985 (PDF)]
|manuals=
* [http://w140.com/frye_s4_gate.pdf George Frye's Explanation of S-4 sampler in October 1968 Service Scope (PDF)]
* [[Media:070-0896-00.pdf|Tektronix S-4 Manual 1969]] (OCR)
* [[Media:070-0896-01 march 1985.pdf|Tektronix S-4 Instruction Manual, Revised March 1985]] (OCR)
* [[Media:070-0896-01.pdf|Tektronix S-4 Instruction Manual, Revised October 1986]] (OCR)
* [[Media:Frye s4 gate.pdf|George Frye's Explanation of S-4 sampler in October 1968 Service Scope]]
* [[Media:Tek s-4 fcp april 1969 - OCR.pdf|Tektronix S-4 Factory Calibration Procedure, April 1969]] (OCR)
}}
}}
The '''Tektronix S-4''' is a sampling head for 7000- and 3S-series samplers. It was designed by [[George Frye]] and [[introduced in 1968]]. It is the fastest of the S-series plug-in samplers.  
The '''Tektronix S-4''' is a sampling head for 7000- and 3S-series samplers.
It was designed by [[George Frye]] and [[introduced in 1968]].
It is the fastest of the S-series plug-in samplers.  


{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Rise time | 25 ps (observed with [[S-50]] or [[S-52]], 35 ps) }}
{{Spec | Rise time | 25 ps (35 ps observed with [[S-50]] or [[S-52]]) }}
{{Spec | Bandwidth | 14.5 GHz }}
{{Spec | Bandwidth | 14.5 GHz }}
{{Spec | Input impedance | 50 Ω (terminated [[SMA connector]])}}
{{Spec | Input impedance | 50 Ω (terminated [[SMA connector]])}}
{{Spec | Input range | operating, 1 V<sub>p-p</sub>; max. safe overload, ±5 V }}
{{Spec | Input voltage | 1 V<sub>p-p</sub> (operating) }}
{{Spec | Maximum input | ±5 V max. non-destructive  }}
{{Spec | Noise | < 5 mV}}
{{Spec | Noise | < 5 mV}}
{{Spec | Features |
{{Spec | Features |
Line 26: Line 33:


==Internals==
==Internals==
The S-4 sampling gate is based upon a traveling wave trapped-charge transmission line in which the sampling window is set by the propagation time of a pulse edge through a thick-film transmission line. This technique requires only a sharp pulse edge rather than a precise pulse width, which is harder to generate.
The [[Sampler#Six-Diode_Sampler|S-4 sampling gate]] is based upon a traveling wave trapped-charge transmission line  
in which the sampling window is set by the propagation time of a pulse edge through a thick-film transmission line.  
This technique requires only a sharp pulse edge rather than a precise pulse width, which is harder to generate.
The sampling diodes are housed in a special coaxial connector that provides a high bandwidth signal path.
The sampling diodes are housed in a special coaxial connector that provides a high bandwidth signal path.


To disassemble the sampler hybrid, first remove it from the sampler board as per the manual. Remove the input
During the development of the S-4, the velocity gate theory was tested using
connector using a 7/32" wrench and remove the 20 dB attenuator with small plyers. The ceramic board is held
a length of transmission line between diodes.
to the housing using roll pins that can be pressed out with a 0.030" pin punch. The hybrid has six diodes,
This led to an aperture time that depended upon twice the propagation delay of the length of transmission line.
each about 0.75mm square. The cathodes are glued to the gold substrate with conductive epoxy and the anodes
 
are wire-bonded (twice) over a gap to the next step in the strobe line. It appears that a standard beam-lead
To disassemble the sampler hybrid, first remove it from the sampler board as per the manual.
diode may fit across the gap but cleanly removing a failed diode without damaging the substrate would be
Remove the input connector using a 7/32" wrench and remove the 20 dB attenuator with small pliers.
quite difficult.
The ceramic board is held to the housing using roll pins that can be pressed out with a 0.030" pin punch.
 
The hybrid has six diodes, each about 0.75 mm².
The cathodes are glued to the gold substrate with conductive epoxy and the anodes
are wire-bonded (twice) over a gap to the next step in the strobe line.
It appears that a standard beam-lead diode may fit across the gap
but cleanly removing a failed diode without damaging the substrate would be quite difficult.
 
==Prices==
1979: $1,435 (~$6,000 in 2023 dollars)
 
According to an [[Media:Tek Schottky Diodes Memo rot.pdf|internal memo]], annual sales were estimated at 150 units in 1979.


==Links==
==Links==
* [http://www.amplifier.cd/Test_Equipment/Tektronix/Tektronix_7000_series_special/S4.html S-4 page @ amplifier.cd]
* [http://www.amplifier.cd/Test_Equipment/Tektronix/Tektronix_7000_series_special/S4.html S-4 page @ amplifier.cd]
* [https://kh6htv.files.wordpress.com/2015/11/an-02a-oscopes.pdf James R. Andrews, ''Comparison of Ultra-Fast Rise Sampling Oscilloscopes''. Picosecond Pulse Labs App Note AN-2a, 1989]
* [https://kh6htv.files.wordpress.com/2015/11/an-02a-oscopes.pdf James R. Andrews, ''Comparison of Ultra-Fast Rise Sampling Oscilloscopes''. Picosecond Pulse Labs App Note AN-2a, 1989]


==Pictures==
==Pictures==
<gallery>
<gallery>
File:Tek-s-4.jpg
Tek-s-4.jpg
File:Tek s4.jpg
Tek s4.jpg
File:S4_top.jpg|Top view of the S4 plug-in
S4_top.jpg | Top view of the S4 plug-in
File:S4_left.jpg|Left view
S4_left.jpg | Left view
File:S4_right.jpg|Right view
S4_right.jpg |Right view
File:S4 schem.png|Schematic
S4 schem.png | Schematic
File:Tektronix-S4-sampler-board-strobe.jpg|Sampler board, strobe side
Tektronix-S4-sampler-board-strobe.jpg | Sampler board, strobe side
File:Tektronix-S4-sampler-board-preamp.jpg|Sampler board, preamp side
Tektronix-S4-sampler-board-preamp.jpg | Sampler board, preamp side
File:Tektronix-S4-sampler-board-hybrid.jpg|Sampler board, disassembled with parts orientation
Tektronix-S4-sampler-board-hybrid.jpg | Sampler board, disassembled with parts orientation
File:Tektronix-S4-hybrid-internal.jpg|Microphotograph of sampler hybrid
Tektronix-S4-hybrid-internal.jpg | Microphotograph of sampler hybrid
S-4_B15_prototype.JPG | S-4 B-prototype, no difference to standard S-4
Tek s-4 in 7s11.jpg | S-4 in [[7S11]]
7s11-s4.jpg | S-4 in [[7S11]]
</gallery>
</gallery>


==Parts==
{{Parts|S-4}}


[[Category:7000 and 3S series sampling heads]]
[[Category:7000 and 3S series sampling heads]]

Latest revision as of 06:16, 30 January 2024

Manuals – Specifications – Links – Pictures

The Tektronix S-4 is a sampling head for 7000- and 3S-series samplers. It was designed by George Frye and introduced in 1968. It is the fastest of the S-series plug-in samplers.

Key Specifications

Rise time 25 ps (35 ps observed with S-50 or S-52)
Bandwidth 14.5 GHz
Input impedance 50 Ω (terminated SMA connector)
Input voltage 1 Vp-p (operating)
Maximum input ±5 V max. non-destructive
Noise < 5 mV
Features
  • trigger signal pick-off for internal triggering

Internals

The S-4 sampling gate is based upon a traveling wave trapped-charge transmission line in which the sampling window is set by the propagation time of a pulse edge through a thick-film transmission line. This technique requires only a sharp pulse edge rather than a precise pulse width, which is harder to generate. The sampling diodes are housed in a special coaxial connector that provides a high bandwidth signal path.

During the development of the S-4, the velocity gate theory was tested using a length of transmission line between diodes. This led to an aperture time that depended upon twice the propagation delay of the length of transmission line.

To disassemble the sampler hybrid, first remove it from the sampler board as per the manual. Remove the input connector using a 7/32" wrench and remove the 20 dB attenuator with small pliers. The ceramic board is held to the housing using roll pins that can be pressed out with a 0.030" pin punch.

The hybrid has six diodes, each about 0.75 mm². The cathodes are glued to the gold substrate with conductive epoxy and the anodes are wire-bonded (twice) over a gap to the next step in the strobe line. It appears that a standard beam-lead diode may fit across the gap but cleanly removing a failed diode without damaging the substrate would be quite difficult.

Prices

1979: $1,435 (~$6,000 in 2023 dollars)

According to an internal memo, annual sales were estimated at 150 units in 1979.

Links

Pictures

Parts

Some Parts Used in the S-4

Part Part Number(s) Class Description Used in
152-0335-00 152-0335-00 Discrete component step recovery diode S-4 S-6
152-0335-01 152-0335-01 Discrete component 150 ps step recovery diode 1502 S-2 S-4 S-6
155-0001-00 155-0001-00 Hybrid integrated circuit gate assembly S-4