S-53: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
The Tektronix S-53 | {{Plugin Sidebar | | ||
is rated to 1 GHz and has a BNC input with 50 Ω impedance. It uses tunnel diode triggering with an | title=Tektronix S-53 | | ||
amplifier before the tunnel diode. The input signal to trigger out | summary=Trigger Recognizer | | ||
image=S53-crop.jpg | | |||
caption=S-53 head | | |||
series=[[:Category:Sampling plugins|7000/S3 series Sampling Plugins]] | | |||
years=? – ? | | |||
manuals= | |||
* [http://w140.com/tek_s53_oct1987.pdf Tektronix S-53 Manual (October 1987, good quality, PDF)] | |||
* [http://w140.com/tek_s53.pdf Tektronix S-53 Manual (bad text, good schematic) (PDF)] | |||
* [http://w140.com/tek_s53_good.pdf Tektronix S-53 Manual (good text, bad schematic) (PDF)] | |||
* [http://w140.com/tek_s53_sch.png Tektronix S-53 Schematic (PNG)] | |||
}} | |||
The Tektronix S-53 '''Trigger Recognizer''' is essentially the entire trigger circuit of an oscilloscope. | |||
It is rated to 1 GHz and has a BNC input with 50 Ω impedance. It uses tunnel diode triggering with an | |||
amplifier before the tunnel diode. The jitter from input signal to trigger-out is rated at 15 ps or less. | |||
The trigger-out signal is 1 V into 50 Ω with 600 mV/ns slew rate. | The trigger-out signal is 1 V into 50 Ω with 600 mV/ns slew rate. | ||
| Line 8: | Line 21: | ||
used for selecting the trigger polarity. The differential amplifier (i.e., phase splitter) generates | used for selecting the trigger polarity. The differential amplifier (i.e., phase splitter) generates | ||
both phases, inverted and noninverted. Depending on the position of the trigger polarity switch, one | both phases, inverted and noninverted. Depending on the position of the trigger polarity switch, one | ||
or the other of the phases is shunted by | or the other of the phases is shunted by 200 Ω resistor. The two signals are buffered by common-base | ||
amplifiers Q20 and Q22, whose collector currents are summed. R25 sets up a bias current on trigger | amplifiers Q20 and Q22, whose collector currents are summed. R25 sets up a bias current on trigger | ||
tunnel diode CR25. The extra current from Q20 or Q22 pushes CR25 over its peak current, and it switches | tunnel diode CR25. The extra current from Q20 or Q22 pushes CR25 over its peak current, and it switches | ||
to the high voltage state. | to the high voltage state. | ||
==Specifications== | |||
==Pictures== | |||
<gallery> | <gallery> | ||
File:Tek s53 front.jpg | File:Tek s53 front.jpg | ||
Revision as of 07:55, 18 May 2014
The Tektronix S-53 Trigger Recognizer is essentially the entire trigger circuit of an oscilloscope. It is rated to 1 GHz and has a BNC input with 50 Ω impedance. It uses tunnel diode triggering with an amplifier before the tunnel diode. The jitter from input signal to trigger-out is rated at 15 ps or less. The trigger-out signal is 1 V into 50 Ω with 600 mV/ns slew rate.
The signal first passes through a compensated NPN differential amplifier, Q10 and Q12, which provides an adjustable trigger offset voltage and trigger polarity selection. Switching diodes CR6 and CR8 are used for selecting the trigger polarity. The differential amplifier (i.e., phase splitter) generates both phases, inverted and noninverted. Depending on the position of the trigger polarity switch, one or the other of the phases is shunted by 200 Ω resistor. The two signals are buffered by common-base amplifiers Q20 and Q22, whose collector currents are summed. R25 sets up a bias current on trigger tunnel diode CR25. The extra current from Q20 or Q22 pushes CR25 over its peak current, and it switches to the high voltage state.
Specifications
Pictures
-
-
-
Front
-
Front
-
Schematic
-
-
-
-
-
