PS503/Repairs: Difference between revisions
Jump to navigation
Jump to search
(Created page with "* Article on Repair of Tektronix FG502 by amplifier.de") |
|||
(9 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
* [ | * [https://www.youtube.com/watch?v=h5ZH7e3sXbo Tektronix PS503A Power Supply Restoration] by NFM @ YouTube | ||
==PS503A Manual== | |||
There are errors in the circuit drawing: | |||
* All amplifiers are connected to +5 V or -5 V. In fact they are connected to the +6.2 V or -6.2 V supply. | |||
* R48 is missing on the grid location table. It is in F1. | |||
* Other parts are missing on the grid location table (Q25, ...) | |||
==PS503A: Instable Output/Output voltage is decreasing with time== | |||
Problem: The output is instable (±100 mV) and is decreasing with time. Both output chanels behave symetrical.<br> | |||
Solution: The faulty part was C34 (4.7 µF/50 V). C34 stabilises the reference voltage. Measuring C34 with an RLC-meter shows no fault: 5.0 µF and a serial resistance of 5 Ω. The faulty behaviour of C34 can only be seen by applying a DC voltage (see picture). | |||
C34 is shorted by the output-on button. So, replacing C34 with a tantalum capacitor is not recommended. | |||
==PS503A: Replacing the voltage indicator light bulb with a LED== | |||
to preserve the effect that the indicator lights up with higher output voltage, some resistor have to be changed. | |||
* R48 (+ output) and R148 (- output) limits the low current that will always flow when the output is ON. This current will flow at 0 V output voltage. (supplied by +33 V / -33 V) | |||
* R55 (+ output) and R155 (- output) limits the high current that will be added to the low current according to the output voltage. (supplied by the 0 to 20 V output voltage) | |||
* The LED should be pushed as deep as possible into the bulb holder, so it holds the yellow plastic window part in place. | |||
* Choose R48/R148 and R55/R155 according the chosen LED (LED current and power dissipation of the resistor) | |||
* R48 is missing on the grid location table. It is in F1. | |||
==Pictures== | |||
<gallery> | |||
PS503A - Current C34.png|DC current thru a faulty C34 (12 V / 10 mA limit) | |||
</gallery> | |||
[[Category:Instrument repair reports]] |
Latest revision as of 10:09, 28 February 2024
- Tektronix PS503A Power Supply Restoration by NFM @ YouTube
PS503A Manual
There are errors in the circuit drawing:
- All amplifiers are connected to +5 V or -5 V. In fact they are connected to the +6.2 V or -6.2 V supply.
- R48 is missing on the grid location table. It is in F1.
- Other parts are missing on the grid location table (Q25, ...)
PS503A: Instable Output/Output voltage is decreasing with time
Problem: The output is instable (±100 mV) and is decreasing with time. Both output chanels behave symetrical.
Solution: The faulty part was C34 (4.7 µF/50 V). C34 stabilises the reference voltage. Measuring C34 with an RLC-meter shows no fault: 5.0 µF and a serial resistance of 5 Ω. The faulty behaviour of C34 can only be seen by applying a DC voltage (see picture).
C34 is shorted by the output-on button. So, replacing C34 with a tantalum capacitor is not recommended.
PS503A: Replacing the voltage indicator light bulb with a LED
to preserve the effect that the indicator lights up with higher output voltage, some resistor have to be changed.
- R48 (+ output) and R148 (- output) limits the low current that will always flow when the output is ON. This current will flow at 0 V output voltage. (supplied by +33 V / -33 V)
- R55 (+ output) and R155 (- output) limits the high current that will be added to the low current according to the output voltage. (supplied by the 0 to 20 V output voltage)
- The LED should be pushed as deep as possible into the bulb holder, so it holds the yellow plastic window part in place.
- Choose R48/R148 and R55/R155 according the chosen LED (LED current and power dissipation of the resistor)
- R48 is missing on the grid location table. It is in F1.
Pictures
-
DC current thru a faulty C34 (12 V / 10 mA limit)