7503: Difference between revisions
No edit summary |
No edit summary |
||
(26 intermediate revisions by 3 users not shown) | |||
Line 1: | Line 1: | ||
{{Oscilloscope Sidebar| | {{Oscilloscope Sidebar | ||
|manufacturer=Tektronix | |||
image= | |series=7000-series scopes | ||
caption=Tektronix 7503, | |model=7503 | ||
introduced=1970 | | |image=Tektronix 7503 front in operation.jpg | ||
discontinued=1972 | | |caption=Tektronix 7503, 2×[[7A12]], [[7B53A]] | ||
summary= | |introduced=1970 | ||
manuals= | |discontinued=1972 | ||
* [ | |summary=90 MHz non-storage mainframe | ||
|designers=Phil Crosby;Hans Springer | |||
|manuals= | |||
* [[Media:070-1039-00.pdf|7503 Instruction Manual]] (schematics, OCR) | |||
}} | }} | ||
The '''Tektronix 7503''' is a 90 MHz 7000-series mainframe with three module bays, [[introduced in 1970]]. It was effectively replaced by the larger-screen [[7603]] in 1972. | |||
The | The 7503 project was managed by [[Phil Crosby]], and was supposed to be a [[7504]] but with one fewer plug-in. | ||
The 7503 was Tek's first scope to use a [[harmonica connector]] for inter-board wiring. | |||
Prior to this, inter-board wiring had either mainly been point-to-point soldered. | |||
Other approaches were taken on certain instruments, for example the [[7704]], in which pins sticking out of the chassis mate with holes in the boards that receive the pins and make electrical contact. | |||
Unlike later three-slot (7xx3) mainframes, the 7503 does supply the +5 V lamp rail, which helps with the contemporary [[7A12]] plug-in. | |||
It also features the [[7000-series remote control connector]] at the rear of the unit. | |||
[[ | {{BeginSpecs}} | ||
{{Spec | Bandwidth | 90 MHz with [[7A11]], [[7A16]] (and faster plug-ins); 75 MHz with [[7A12]], [[7A13]], [[7A14]] }} | |||
{{Spec | Fastest calibrated sweep | 5 ns/Div }} | |||
{{Spec | CRT | [[T7500|T7500 (154-0608-xx)]], 18 kV total acceleration (+15/−2.96) }} | |||
{{Spec | Calibrator | 4 mV to 40 V in five decade steps, 40 mA, 1 kHz ±0.5% }} | |||
{{Spec | Outputs | Side panel: Vert signal, +Gate, +Sawtooth; At CRT: Camera power }} | |||
{{Spec | Power | 90−110 V / 104−126 V / 112−136 V / 180−220 V / 208−252 V / 224−272 V, 50−440 Hz; max. 258 W }} | |||
{{Spec | Weight | 21.3 kg / 47 lb (instrument only) }} | |||
{{Spec | Rear connectors | | |||
* High speed Z Axis input (BNC connector, 60 V<sub>p-p</sub>, 75 MHz) | |||
* High sensitivity Z Axis input (BNC connector, 2 V<sub>p-p</sub>, 10 MHz) | |||
* Two [[LEMO S-series connector]]s for [[probe power]] | |||
* [[Amphenol 165 series connectors|Amphenol 165-16 connector]] (J1075) for [[7503, 7504, 7904 remote control connector|remote control]] (single sweep ready/reset signals) | |||
}} | |||
{{EndSpecs}} | |||
==Links== | |||
{{Documents|Link=7503}} | |||
{{PatentLinks|7503}} | |||
==Internals== | |||
In addition to two custom Tek ICs, the 7503 uses CA3046 transistor arrays ([[156-0048-00]]) in eight places (five on the regulator board). The vertical and horizontal amplifiers are built using discrete transistors. | |||
The 7503 has an X-Y delay compensation network that is activated when the H plugin is an amplifier or a timebase in amplifier mode (see [[7000 Series plug-in interface]]). | |||
This network is switched in using a pair of [[148-0034-00]] miniature relays on the horizontal amplifier board. | |||
Like other 75xx and 76xx mainframes and the 7504, the 7503 has a linear power supply, as opposed to the switchmode supplies used in the later 4-slot mainframes. In addition to the +5 V, ±15 V, ±50 V rails common to the 7000 series, internally (not on the plug-in slots) it has a +75 V output not found in later models, and a +150 V instead of the later +130 V. | |||
The 7503 contains a mercury-based [[elapsed time meter]] on the rear of the main interface board. | |||
==Pictures== | ==Pictures== | ||
<gallery> | <gallery> | ||
Tek 7503 front.JPG|Front | Tektronix 7503 front in operation.jpg | ||
7503 DSC 0883.JPG|Plug-in bay | Tektronix 7503 front in operation.jpg | ||
7503 DSC 0895.JPG|Plug-in connectors missing sides | Tek 7503cl3.jpg | ||
7503 DSC 0894.JPG|Horizontal amp on top | Tek 7503 front.JPG | Front | ||
7503 DSC 0891.JPG|Vertical amp on the side | 7503 DSC 0883.JPG | Plug-in bay | ||
7503 DSC 0888.JPG|Left view, delay cable, CRT | 7503 DSC 0895.JPG | Plug-in connectors missing sides | ||
7503 DSC 0887.JPG|Left view, power supply | 7503 backplane r1.jpg | 7503 backplane PCB [[Repairing 7000-series plug-in sockets#Replacing the connectors with modern equivalents|mid-repair]] | ||
7503 DSC 0886.JPG|Right view, mains frequency transformer | 7503 DSC 0894.JPG | Horizontal amp on top | ||
7503 DSC 0885.JPG|Readout board | 7503 DSC 0891.JPG | Vertical amp on the side | ||
DSC 0878.JPG|Right side connector panel | 7503 DSC 0888.JPG | Left view, delay cable, CRT | ||
DSC 0880.JPG|Rear | 7503 DSC 0887.JPG | Left view, power supply | ||
7503 DSC 0886.JPG | Right view, mains frequency transformer | |||
7503 DSC 0885.JPG | Readout board | |||
DSC 0878.JPG | Right side connector panel | |||
DSC 0880.JPG | Rear | |||
Tek 7503cl3.jpg | Tek 7503cl3.jpg | ||
Tek 7503cl1.jpg | Tek 7503cl1.jpg | ||
Tek 7503cl2.jpg | Tek 7503cl2.jpg | ||
</gallery> | </gallery> | ||
==Components== | |||
{{Parts|7503}} | |||
{{Custom ICs|7000 series readout system}} | |||
[[Category:7000 series non-storage mainframes]] | [[Category:7000 series non-storage mainframes]] | ||
[[Category:7000 series mainframes with linear power supplies]] |
Latest revision as of 10:03, 24 June 2024
The Tektronix 7503 is a 90 MHz 7000-series mainframe with three module bays, introduced in 1970. It was effectively replaced by the larger-screen 7603 in 1972.
The 7503 project was managed by Phil Crosby, and was supposed to be a 7504 but with one fewer plug-in. The 7503 was Tek's first scope to use a harmonica connector for inter-board wiring. Prior to this, inter-board wiring had either mainly been point-to-point soldered. Other approaches were taken on certain instruments, for example the 7704, in which pins sticking out of the chassis mate with holes in the boards that receive the pins and make electrical contact.
Unlike later three-slot (7xx3) mainframes, the 7503 does supply the +5 V lamp rail, which helps with the contemporary 7A12 plug-in. It also features the 7000-series remote control connector at the rear of the unit.
Key Specifications
Bandwidth | 90 MHz with 7A11, 7A16 (and faster plug-ins); 75 MHz with 7A12, 7A13, 7A14 |
---|---|
Fastest calibrated sweep | 5 ns/Div |
CRT | T7500 (154-0608-xx), 18 kV total acceleration (+15/−2.96) |
Calibrator | 4 mV to 40 V in five decade steps, 40 mA, 1 kHz ±0.5% |
Outputs | Side panel: Vert signal, +Gate, +Sawtooth; At CRT: Camera power |
Power | 90−110 V / 104−126 V / 112−136 V / 180−220 V / 208−252 V / 224−272 V, 50−440 Hz; max. 258 W |
Weight | 21.3 kg / 47 lb (instrument only) |
Rear connectors |
|
Links
Documents Referencing 7503
Document | Class | Title | Authors | Year | Links |
---|---|---|---|---|---|
Tekscope 1970 V2 N3 Jun 1970.pdf | Article | The 7000-Series Oscilloscopes as Signal Sources | 1970 | 7704 • 7504 • 7503 | |
Tekscope 1970 V2 N5 Oct 1970.pdf | Article | Amplitude Measurement to Better Than 1% | 1970 | 1S1 • 7503 • 7A13 • 1A5 • W • 3A7 |
Patents that may apply to 7503
Page | Title | Inventors | Filing date | Grant date | Links |
---|---|---|---|---|---|
Patent US 3453403A | Power selection device | Eldon Hoffman | 1966-08-18 | 1969-07-01 | 115 • 140 • 141 • 141A • 145 • 146 • 147 • 148 • 149 • 149A • 230 • 286 • 453 • 454 • 491 • 520A • 521A • 522 • 545B • 547 • 556 • 561B • 564B • 568 • 576 • 611 • 647A • 2601 • 5030 • R5030 • 5031 • R5031 • 7503 • 7504 • 7704 • 7704A • 7904 • R7903 |
Internals
In addition to two custom Tek ICs, the 7503 uses CA3046 transistor arrays (156-0048-00) in eight places (five on the regulator board). The vertical and horizontal amplifiers are built using discrete transistors.
The 7503 has an X-Y delay compensation network that is activated when the H plugin is an amplifier or a timebase in amplifier mode (see 7000 Series plug-in interface). This network is switched in using a pair of 148-0034-00 miniature relays on the horizontal amplifier board.
Like other 75xx and 76xx mainframes and the 7504, the 7503 has a linear power supply, as opposed to the switchmode supplies used in the later 4-slot mainframes. In addition to the +5 V, ±15 V, ±50 V rails common to the 7000 series, internally (not on the plug-in slots) it has a +75 V output not found in later models, and a +150 V instead of the later +130 V.
The 7503 contains a mercury-based elapsed time meter on the rear of the main interface board.
Pictures
-
-
-
-
Front
-
Plug-in bay
-
Plug-in connectors missing sides
-
7503 backplane PCB mid-repair
-
Horizontal amp on top
-
Vertical amp on the side
-
Left view, delay cable, CRT
-
Left view, power supply
-
Right view, mains frequency transformer
-
Readout board
-
Right side connector panel
-
Rear
-
-
-
Components
Some Parts Used in the 7503