492: Difference between revisions

39 bytes added ,  7 July 2019
no edit summary
No edit summary
No edit summary
Line 25: Line 25:


Rear panel inputs/outputs are: PROBE POWER (Provides operating voltages (+5V, -15 V, +15 V; 100 mA max each) for active probes); HORIZ|TRIG (EXT IN) [[BNC connector]] (A dual function connector: When in External Triggering mode the connector is an AC coupled input for trigger signals.  When the TIME/DIV selection is EXT the connector is a DC coupled input for horizontal sweep voltages); MARKER/VIDEO (OUTPUT) (B053575 AND UP) or EXT PRESELECTOR (OUTPUT) (B053574 and below) [[BNC connector]] (MARKER/VIDEO interfaces the 492/492P with a TV Sideband Adapter, such as the Tek 1405, so a marker from the adapter is displayed on the internal video.  External video applied to this connector will also be displayed if pin 1 of the ACCESSORIES connector is grounded.  EXT PRESELECTOR provides a variable voltage (approx -0.2 V to +10 V) that is proportional to center frequency, for preselector bands of Opt. 01 instruments, to drive an external preselector.); Opt. 42 replaces MARKER/VIDEO (OUTPUT) with 110 MHz IF (OUTPUT) [[BNC connector]] (Provides 3 dB signal bandwidth ≥ 4.5 MHz); HORIZ (OUTPUT) [[BNC connector]] (Supplies a 0.5 V/div horizontal signal); VERT (OUTPUT) [[BNC connector]] (Provides access to the video signal with 0.5 V for each division of displayed video above or below the center line.); PEN LIFT (OUTPUT) [[BNC connector]] (Provides access to a TTL compatible signal to lift the pen of a chart recorder during sweep retrace.  In Opt. 42 instruments this port may also be used for inputting external video, if pin 1 of the ACCESSORIES connector is ground); use this connector to input external video signals if pin 1 of the ACCESSORIES connector is grounded); 10 MHz IF (OUTPUT) [[BNC connector]] (Provides access to the output of the 10 MHz IF); J104 ACCESSORY (B053575 AND UP) female [[DB25 connector]] (Provides bidirectional access to the instrument bus.  For instruments B053574 and below, this connector has no application.); IEEE STD 488 PORT [[GPIB interface]] (Added to all "P" suffixed instruments)
Rear panel inputs/outputs are: PROBE POWER (Provides operating voltages (+5V, -15 V, +15 V; 100 mA max each) for active probes); HORIZ|TRIG (EXT IN) [[BNC connector]] (A dual function connector: When in External Triggering mode the connector is an AC coupled input for trigger signals.  When the TIME/DIV selection is EXT the connector is a DC coupled input for horizontal sweep voltages); MARKER/VIDEO (OUTPUT) (B053575 AND UP) or EXT PRESELECTOR (OUTPUT) (B053574 and below) [[BNC connector]] (MARKER/VIDEO interfaces the 492/492P with a TV Sideband Adapter, such as the Tek 1405, so a marker from the adapter is displayed on the internal video.  External video applied to this connector will also be displayed if pin 1 of the ACCESSORIES connector is grounded.  EXT PRESELECTOR provides a variable voltage (approx -0.2 V to +10 V) that is proportional to center frequency, for preselector bands of Opt. 01 instruments, to drive an external preselector.); Opt. 42 replaces MARKER/VIDEO (OUTPUT) with 110 MHz IF (OUTPUT) [[BNC connector]] (Provides 3 dB signal bandwidth ≥ 4.5 MHz); HORIZ (OUTPUT) [[BNC connector]] (Supplies a 0.5 V/div horizontal signal); VERT (OUTPUT) [[BNC connector]] (Provides access to the video signal with 0.5 V for each division of displayed video above or below the center line.); PEN LIFT (OUTPUT) [[BNC connector]] (Provides access to a TTL compatible signal to lift the pen of a chart recorder during sweep retrace.  In Opt. 42 instruments this port may also be used for inputting external video, if pin 1 of the ACCESSORIES connector is ground); use this connector to input external video signals if pin 1 of the ACCESSORIES connector is grounded); 10 MHz IF (OUTPUT) [[BNC connector]] (Provides access to the output of the 10 MHz IF); J104 ACCESSORY (B053575 AND UP) female [[DB25 connector]] (Provides bidirectional access to the instrument bus.  For instruments B053574 and below, this connector has no application.); IEEE STD 488 PORT [[GPIB interface]] (Added to all "P" suffixed instruments)


---------------------------------------------------------
---------------------------------------------------------
Specifications based on final published documentation, unless otherwise specified.
<div style='text-align: center;'>Specifications based on final published documentation, unless otherwise specified.</div>
 
{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Frequency Range |  
{{Spec | Frequency Range |  
1,192

edits