1S1: Difference between revisions

From TekWiki
Jump to navigation Jump to search
(typos)
No edit summary
Line 1: Line 1:
The 1S1 is a sampling plug-in for 500-series scopes.  It is essentially one channel of a sampling unit and a timing unit from a 661.  It has its own trigger and timebase.  The oscilloscope's timebase is usually set to a relatively slow sweep rate when using a 1S1.  Alternatively, the sweep on
The 1S1 is a sampling plug-in for 500-series scopes.  It is essentially one channel of a sampling unit and a timing unit from a [[661]].   
the oscilloscope can be free-run, and the horizontal voltage from the oscilloscope can be used to control the 1S1, as described below. The 1S1 has a 50-Ohm GR connector for signal input.  The plug-in supplies power (+100V and -12.6V) to active probes such as the P6032 cathode follower probe.   
It has its own trigger and timebase.   
The oscilloscope's timebase is usually set to a relatively slow sweep rate when using a 1S1.   
Alternatively, the sweep on the oscilloscope can be free-run,  
and the horizontal voltage from the oscilloscope can be used to control the 1S1, as described below.  
The 1S1 has a 50-Ohm GR-874connector for signal input.   
The plug-in supplies power (+100V and -12.6V) to active probes such as the [[P6032]] cathode follower probe.   


The 1S1 can operate in normal self-swept mode or an external sweep signal can be applied to the 1S1.  With the 1S1's internal sweep disabled, the horizontal-in and vertical-out connections can be used so the the 1S1 acts as a lookup table, a mapping of x to y, a function.   
The 1S1 can operate in normal self-swept mode or an external sweep signal can be applied to the 1S1.   
The 661 also has this capability, in its "A vert/B horiz" mode, which is like X-Y mode for a sampler.  In this mode, the horizontal-in voltage controls to the time after the trigger event when the sample should be taken, and the vertical-out voltage corresponds to the voltage measured at that instant.  This allows a waveform to be digitized using an arbitrarily slow DAC to generate the horizontal voltage and ADC to read the sampled output.  But perhaps more importantly, by setting a constant horizontal-in voltage, it allows the output signal at one equivalent time instant to be processed in the time domain.  For example, this allows the voltage to be low-pass filtered, so that it can be more accurately measured.  The other reason why one might want a signal the consists of multiple sequential measurements of the same equivalent-time instant is that statistics can be calculated on these observations.  For example, one might want to know, when testing a logic gate, what is the propagation delay such that 99.9% of the transitions happen faster than this.  The horizontal-in voltage can also be produced, in "manual" mode, by setting a knob on the 1S1.
With the 1S1's internal sweep disabled, the horizontal-in and vertical-out connections can be used  
so the the 1S1 acts as a lookup table, a mapping of x to y, a function.   
The 661 also has this capability, in its "A vert/B horiz" mode, which is like X-Y mode for a sampler.   
In this mode, the horizontal-in voltage controls to the time after the trigger event when the sample should be taken,  
and the vertical-out voltage corresponds to the voltage measured at that instant.   
This allows a waveform to be digitized using an arbitrarily slow DAC to generate the horizontal voltage  
and ADC to read the sampled output.  But perhaps more importantly, by setting a constant horizontal-in voltage,  
it allows the output signal at one equivalent time instant to be processed in the time domain.   
For example, this allows the voltage to be low-pass filtered, so that it can be more accurately measured.   
The other reason why one might want a signal the consists of multiple sequential measurements  
of the same equivalent-time instant is that statistics can be calculated on these observations.   
For example, one might want to know, when testing a logic gate, what is the propagation delay  
such that 99.9% of the transitions happen faster than this.   
The horizontal-in voltage can also be produced, in "manual" mode, by setting a knob on the 1S1.

Revision as of 13:13, 3 July 2010

The 1S1 is a sampling plug-in for 500-series scopes. It is essentially one channel of a sampling unit and a timing unit from a 661. It has its own trigger and timebase. The oscilloscope's timebase is usually set to a relatively slow sweep rate when using a 1S1. Alternatively, the sweep on the oscilloscope can be free-run, and the horizontal voltage from the oscilloscope can be used to control the 1S1, as described below. The 1S1 has a 50-Ohm GR-874connector for signal input. The plug-in supplies power (+100V and -12.6V) to active probes such as the P6032 cathode follower probe.

The 1S1 can operate in normal self-swept mode or an external sweep signal can be applied to the 1S1. With the 1S1's internal sweep disabled, the horizontal-in and vertical-out connections can be used so the the 1S1 acts as a lookup table, a mapping of x to y, a function. The 661 also has this capability, in its "A vert/B horiz" mode, which is like X-Y mode for a sampler. In this mode, the horizontal-in voltage controls to the time after the trigger event when the sample should be taken, and the vertical-out voltage corresponds to the voltage measured at that instant. This allows a waveform to be digitized using an arbitrarily slow DAC to generate the horizontal voltage and ADC to read the sampled output. But perhaps more importantly, by setting a constant horizontal-in voltage, it allows the output signal at one equivalent time instant to be processed in the time domain. For example, this allows the voltage to be low-pass filtered, so that it can be more accurately measured. The other reason why one might want a signal the consists of multiple sequential measurements of the same equivalent-time instant is that statistics can be calculated on these observations. For example, one might want to know, when testing a logic gate, what is the propagation delay such that 99.9% of the transitions happen faster than this. The horizontal-in voltage can also be produced, in "manual" mode, by setting a knob on the 1S1.