TDS744A: Difference between revisions
Jump to navigation
Jump to search
Jaredcabot (talk | contribs) (Added manuals.) |
Jaredcabot (talk | contribs) (Added Option 05 install manual and picture.) |
||
Line 12: | Line 12: | ||
* [[Media:061-4094-02.pdf|TDS, TLS & CTS FDD Replacement 061-4094-02]] | * [[Media:061-4094-02.pdf|TDS, TLS & CTS FDD Replacement 061-4094-02]] | ||
* [[Media:070-8709-07.pdf|TDS400A/500A/600A/700A Programmer 070-8709-07]] | * [[Media:070-8709-07.pdf|TDS400A/500A/600A/700A Programmer 070-8709-07]] | ||
* [[Media:070-8748-02.pdf|TDS Family Opt 05 Video Trigger Interface 070-8709- | * [[Media:070-8748-02.pdf|TDS Family Opt 05 Video Trigger Interface 070-8709-02]] | ||
* [[Media:070-9636-02.pdf|TDS Family Opt 05 Video Trigger Interface Install 070-9636-02]] | |||
* [[Media:070-8990-04.pdf|TDS684A/744A/784A Performance Verification and Specifications 070-8990-04]] | * [[Media:070-8990-04.pdf|TDS684A/744A/784A Performance Verification and Specifications 070-8990-04]] | ||
* [[Media:070-8991-02.pdf|TDS684A/744A/784A User 070-8991-02]] / <small>[[Media:070-8991-02 c2.pdf|Alternate copy]]</small> | * [[Media:070-8991-02.pdf|TDS684A/744A/784A User 070-8991-02]] / <small>[[Media:070-8991-02 c2.pdf|Alternate copy]]</small> | ||
Line 78: | Line 79: | ||
==Pictures== | ==Pictures== | ||
<gallery> | <gallery> | ||
Tek_TDS744A_Front.jpeg | Front | Tek_TDS744A_Front.jpeg|Front | ||
Tek_TDS744A_Back.jpeg | Tek_TDS744A_Back.jpeg|Rear | ||
</gallery> | </gallery> | ||
===Internals=== | ===Internals=== | ||
<gallery> | <gallery> | ||
Tek_TDS744A_Top.jpeg | Top - Processor/Display Board | Tek_TDS744A_Top.jpeg|Top - Processor/Display Board | ||
Tek_TDS744A_Bottom.jpeg |Bottom - Acquisition board | Tek_TDS744A_Bottom.jpeg|Bottom - Acquisition board | ||
Tek_TDS744A_PS_CRT_1.jpeg | Power supply & CRT board | Tek_TDS744A_PS_CRT_1.jpeg|Power supply & CRT board | ||
Tek_TDS744A_PS_CRT_2.jpeg | | Tek_TDS744A_PS_CRT_2.jpeg|Power supply & CRT board | ||
Tek_TDS744A_LHS.jpeg | | Tek_TDS744A_LHS.jpeg|Left Side | ||
Tek_TDS744A_RHS.jpeg | | Tek_TDS744A_RHS.jpeg|Right Side | ||
TDS5-6-700_Option_05_TV_Trigger_Internal_Parts.jpg|Option 05 Internal Parts | |||
</gallery> | </gallery> | ||
[[Category:TDS700 series scopes]] | [[Category:TDS700 series scopes]] |
Revision as of 04:40, 12 November 2021
The TDS744 is a 500 MHz, 2 GS/s four-channel digital scope with a color screen.
Key Specifications
Bandwidth | 500 MHz at 10 mv/div and above; 500 MHz @ 5 mV/div; 500 MHz @ 2 mV/div; 450 MHz @ 1 mV/div |
---|---|
Sample rate | 1 channel @ 2 GS/s, 2 channels @ 1 GS/s, 3 or 4 channels @ 500 MS/s |
Resolution | 8 bit |
Record length | 50k samples per channel (500k with option 1M) |
Acquisition modes | sample, envelope, average, high-resolution, peak-detect |
Display | Color; Zoom |
Trigger modes | Edge, logic, pulse; Video trigger with option 05 (NTSC, SECAM, PAL, HDTV, and FlexFormat) |
Storage | 1.44 Mbyte, 3.5 inch, DOS 3.3-or-later floppy disk. NVRAM storage for saving waveforms, hardcopies, and setups. Units with option HD present (requires additional hardware) have a hard disk drive |
I/O | Full GPIB programmability |
Hardcopy | Using GPIB, RS-232, or Centronics ports |
Software
- TDS700A Field Adjustment Software 063260100 (ZIP)
- Tektronix TDS300, 400, 500, 600, 700, 800 AWE Drivers 066008700 (ZIP)
- Tektronix Wavestar 2012.05.09.11.07.29 16456 EN (ZIP, 102MB) Product Key: WSTRO618650124
Firmware
- TDS744A v1.0e Firmware (ZIP)
- TDS744A v4.2.1e Firmware (ZIP)
Options
- 05 - Video Trigger - Oscilloscope comes with tools that allow investigation of a range of NTSC, PAL, SECAM, and high definition TV signals.
- 1M - 4M acquisition length - Extends standard acquisition length from 50,000 points per channel to 130,000 samples on three or four channels, 250,000 samples on two channels, and 500,000 samples on one channel.
- 13 - RS-232C and Centronics hardcopy interfaces - Add RS-232-C and Centronics interface ports.
- 1F - Floppy disk drive - Add 3.5 inch, 1.44 MByte floppy disc drive.
- 2F - Advanced DSP math - Add advanced DSP math features such as FFT, integration, and differentiation.
- 2C - Communication Signal Analyzer - Oscilloscope comes configured for communications signal triggering and mask testing.
- 3C - P6701B with system calibration - Oscilloscope comes with a P6701B and calibrated short-wavelength optical reference receiver on channel 1.
- 4C - P6703B with system calibration - Oscilloscope comes with a P6703B and calibrated long-wavelength optical reference receiver on channel 1.
- 2M - 8M acquisition length - TDS 520D, 724D: To 2M samples on two channels and 4M on one channel. TDS 540D, 580D, 714L, 754D, 784D, 794D: To 2M samples on three or four channels, 4M on two channels, and 8M samples on one channel (Option includes a hard disk and is only available for the models listed above.)
Links
- Tek Forum threads:
- EEVBlog Forum Threads:
- Simmconn Labs LCD replacement kits for CRT-based TDS O-scopes
- Wavestar Product Key
- TDS error log viewer
Pictures
-
Front
-
Rear
Internals
-
Top - Processor/Display Board
-
Bottom - Acquisition board
-
Power supply & CRT board
-
Power supply & CRT board
-
Left Side
-
Right Side
-
Option 05 Internal Parts