11A32

From TekWiki
Revision as of 21:33, 31 December 2022 by Johnaddis (talk | contribs)
Jump to navigation Jump to search
Tektronix 11A32
400 MHz dual channel vertical plug-in
Tektronix 11A32

Compatible with 11000-series scopes

Produced from 1987 to (?)

Manuals
Manuals – Specifications – Links – Pictures

The Tektronix 11A32 is a 400 MHz dual-channel amplifier plug-in for 11000-series scopes.

Key Specifications

Bandwidth DC to 400 MHz. 100 MHz and 20 MHz four pole BWL (Bandwidth Limit) filters may be selected.
Rise time 875 ps in 1 GHz mainframes such as the 11402, 11402A, 11403, 11403A, DSA601A, or DSA602A
Deflection 1 mV to 10 V per division in 1% calibrated steps
Input impedance 50 Ω or 1 MΩ
Features
  • High-resolution calibrated DC offset
  • Fast overdrive recovery
  • 5 VRMS overload protection in 50 Ω mode, with manual reset

Internals

Analog

Each input channel has a separate attenuator module containing passive 1 megohm attenuators, an AC coupling capacitor, a switch selecting the calibrator or signal input, and an M474 buffer amplifier. The calibrator signal turned off inside the plugin when not in use.


The attenuator module output feeds the + input of the M377 amplifier IC through a (blue) 50 ohm transmission line, one per input channel. The cable lengths set a standard delay per plugin.


The M377's - input is connected to the ACVS (Analog Control Voltage System) output.


The (differential) display outputs of the two amplifiers are hard-wired in parallel and drive the mainframe’s 50 Ω per side input impedance. The same is true of the trigger outputs of the two amplifiers.


The version of the M377 used in the 11A32 has a 100 Ω output impedance per side so that two of them in parallel create a source impedance of 50 Ω.


Each M377 amplifier's nominal common-mode output voltage is zero whether enabled or not. When not enabled, each M377 differential output is exactly zero by design. This fact is used during calibration by the plugin’s firmware to determine the mainframe’s imbalance and compensate for it during normal operation.


Each of the two channels has its own AUX output on dedicated pins of the plug-in interface connector:

See also the block diagram below.

Digital

The 11A32 and the 11A34 use exactly the same firmware.

The 11A32 and 11A34 were originally intended to use Intel 8052 microcontrollers. However, during development, the firmware swelled beyond that chip's 8192-byte maximum on-chip ROM size. Doug Haines found an alternate supplier of 8051-compatible chips (OKI Semiconductor) that offered a 16Kbyte on-chip ROM, and that's what the plug-ins wound up with. The finished code size wound up at about 14 KB.

The 11A32 also contains a DS1120 NVRAM and an ACVS module that generates the analog control voltages needed for gain/offset control etc.

Links

Pictures

Custom ICs used in the 11A32

Page Model Part nos Description Designers Used in
M377 M377 165-2129-03 165-2089-06 155-2089-05 amplifier John Addis 11A16 11A32 11A33 11A34 11A52 2245 2245A 2247 2247A 2252 TDS410 TDS420 TDS460 TDS520D TDS540D TDS580D TDS680C TDS684C TDS714L TDS724D TDS754D TDS784D
M474 M474 amplifier John Addis Ivan John Cousins 11A32 11A34