5000 Series plug-in interface: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 17: Line 17:
! Function
! Function
! Function
! Function
|-  
|- bgcolor="Pink"
|  1 ||   ||
|  1 || +200 V  || +38 V unreg
|- bgcolor="Pink"
|- bgcolor="Pink"
|  2 || Utility GND  || +5 V
|  2 || Utility GND  || +5 V
Line 26: Line 26:
|  4 || Trig out (H) / Right trig in (V) ||  Left trig in (V)
|  4 || Trig out (H) / Right trig in (V) ||  Left trig in (V)
|- bgcolor="Pink"
|- bgcolor="Pink"
|  5 ||   || −30 V
|  5 || +30 V  || −30 V
|- bgcolor="Pink"
|- bgcolor="Pink"
|  6 || +15 V  ||  −15 V
|  6 || +15 V  ||  −15 V
Line 38: Line 38:
| 10 || A gate  || Z Axis B Sweep
| 10 || A gate  || Z Axis B Sweep
|-  
|-  
| 11 || Sample pulse || Load stop
| 11 || Sample pulse ''[note 1]'' || Load stop ''[note 1]''
|-  
|-  
| 12 || Single-sweep mode  ||
| 12 || Single-sweep mode  ||
Line 58: Line 58:
| 20 || Chop activate  ||
| 20 || Chop activate  ||
|-  
|-  
| 21 ||   ||
| 21 || bgcolor="Pink" | −30 V  ||
|-  
|- bgcolor="LightGreen"
| 22 ||   ||
| 22 || TS7  || TS10
|-  
|- bgcolor="LightGreen"
| 23 ||   ||
| 23 || TS5  || TS6
|-  
|- bgcolor="LightGreen"
| 24 ||   || Sweep rate
| 24 || Ch. 2 Col  || Ch. 2 Row / Sweep rate
|-  
|- bgcolor="LightGreen"
| 25 ||   ||
| 25 || TS3  || TS2
|-  
|- bgcolor="LightGreen"
| 26 ||   ||
| 26 || TS8  || TS9
|-  
|- bgcolor="LightGreen"
| 27 ||  ||
| 27 || TS1   || TS4
|-  
|- bgcolor="LightGreen"
| 28 ||   ||
| 28 || Ch. 1 Col  || Ch. 1 Row


|}
|}
==Notes==
* ''note 1'' − [[5223]] / [[5B25N]]


===Pin group function legend===
===Pin group function legend===

Revision as of 11:13, 9 September 2018

Tektronix 5000 series oscilloscope mainframes have two vertical plug-in slots, and one horizontal plug-in slots.

The interconnect on either slot type is a 56-pin PCB edge connector.

Looking into the mainframe from the front panel, "A" pins are left of the connector centerline and "B" are on the right. Pins are numbered from 1 at the bottom to 28 on the top.

  A side B side
Pin Function Function
1 +200 V +38 V unreg
2 Utility GND +5 V
3 Line trigger
4 Trig out (H) / Right trig in (V) Left trig in (V)
5 +30 V −30 V
6 +15 V −15 V
7 +plugin signal −plugin signal
8
9 Z Axis A Sweep Intensify
10 A gate Z Axis B Sweep
11 Sample pulse [note 1] Load stop [note 1]
12 Single-sweep mode
13 +plugin signal −plugin signal
14 Clean GND Return Clean GND Return
15 A sweep ALT drive
16 Lockout B sweep Trace separation
17 Lockout A sweep Single sweep reset
18 Chop sense Display on
19 100 μs/div detect Display chop
20 Chop activate
21 −30 V
22 TS7 TS10
23 TS5 TS6
24 Ch. 2 Col Ch. 2 Row / Sweep rate
25 TS3 TS2
26 TS8 TS9
27 TS1 TS4
28 Ch. 1 Col Ch. 1 Row

Notes

Pin group function legend

Plugin power & ground
HF signals
Readout system signals