Difference between revisions of "5XP"

From TekWiki
Jump to navigation Jump to search
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
The '''Dumont 5XP''' is a family of CRTs produced starting in the 1940s.
+
{{CRT
 +
|Manufacturer=DuMont
 +
|Model=5XP
 +
|Part_nos=
 +
|Description=family of flat-faced 5" CRTs
 +
|Used_in=513;517;
 +
|Designers=
 +
}} with [[multi-band acceleration | multi-band post accelerators]], produced from 1948 onward.  
  
They are used in the [[513]] and [[517]].
+
A 5XP-A series with tighter tolerances followed in 1953, and then a 5XP-B range in 1954 that had an aluminized screen for higher brightness.
  
 +
Compared to earlier tubes, they have improved vertical deflection sensitivity,
 +
which was achieved by decreasing vertical deflection plate width and reducing spacing between the plates,
 +
at the cost of limiting vertical scan to as little as 1.25" (at 20 kV acceleration).
 +
 +
Maximum post-acceleration voltage for the 5XP is 25.5 kV.
 +
Typical conditions are stated as −2 kV on the cathode and +12 kV on the post-acceleration anode.
 +
 +
The 5XP was used in early models of the [[513]] and [[517]], before Tektronix switched these to Tek-made CRTs.
 +
 +
==Links==
 
* [http://w140.com/5XP1A.pdf 5XP1A Datasheet (PDF)]
 
* [http://w140.com/5XP1A.pdf 5XP1A Datasheet (PDF)]
 
* [http://w140.com/5XP1B.pdf 5XP1B Datasheet (PDF)]
 
* [http://w140.com/5XP1B.pdf 5XP1B Datasheet (PDF)]
 +
* {{Keller 1991| p.105}}
  
 +
==Pictures==
 
<gallery>
 
<gallery>
Dumont 5xp11 1.jpg | Dumont 5XP11
+
Dumont 5xp11 1.jpg | DuMont 5XP11
Dumont 5xp11 2.jpg | Dumont 5XP11
+
Dumont 5xp11 2.jpg | DuMont 5XP11
 +
Tek_517_with_5xp_crt.jpg|5XP in a [[517]]
 
</gallery>
 
</gallery>
  
 
[[Category:Cathode ray tubes]]
 
[[Category:Cathode ray tubes]]

Latest revision as of 14:07, 10 October 2021

The DuMont 5XP is a family of flat-faced 5" CRTs with multi-band post accelerators, produced from 1948 onward.

A 5XP-A series with tighter tolerances followed in 1953, and then a 5XP-B range in 1954 that had an aluminized screen for higher brightness.

Compared to earlier tubes, they have improved vertical deflection sensitivity, which was achieved by decreasing vertical deflection plate width and reducing spacing between the plates, at the cost of limiting vertical scan to as little as 1.25" (at 20 kV acceleration).

Maximum post-acceleration voltage for the 5XP is 25.5 kV. Typical conditions are stated as −2 kV on the cathode and +12 kV on the post-acceleration anode.

The 5XP was used in early models of the 513 and 517, before Tektronix switched these to Tek-made CRTs.

Links

Pictures