7B92: Difference between revisions

From TekWiki
Jump to navigation Jump to search
(introduced)
No edit summary
(22 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{Plugin Sidebar 2 |
{{Plugin Sidebar
title=Tektronix 7B92 |
|manufacturer=Tektronix
summary=500 MHz Dual Timebase |
|type=7B92  
image=Tek 7b92 front.jpg |
|summary=500 MHz Dual Timebase  
caption=7B92 front |
|image=7b92a-front.jpg  
introduced=1972 |
|caption=7B92A front  
discontinued=(?) |
|introduced=1971
series=[[7000-series scopes]] |
|discontinued=1992
manuals=
|series=7000-series scopes
|designers=Bill DeVey;Les Larson;Val Garuts
|manuals=
* [http://bama.edebris.com/download/tek/7b92a-2/tek-7b92a.pdf Tektronix 7B92A Manual (PDF)]
* [http://bama.edebris.com/download/tek/7b92a-2/tek-7b92a.pdf Tektronix 7B92A Manual (PDF)]
* [http://w140.com/smb/7b92_sup_sm.pdf Tektronix 7B92 Circuit Description Supplement (OCR, PDF)]
* [http://w140.com/smb/7b92_sup_sm.pdf Tektronix 7B92 Circuit Description Supplement (OCR, PDF)]
* [http://w140.com/smb/7b92_svc_sm.pdf Tektronix 7B92 Service Manual (OCR, PDF)]
* [http://w140.com/smb/7b92_svc_sm.pdf Tektronix 7B92 Service Manual (OCR, PDF)]
* [[Media:070-1192-00.pdf|Tektronix 7B92 Manual (OCR, uncut schematics, PDF)]]
* [http://w140.com/smb/7b92a_op_sm.pdf Tektronix 7B92A Operators Manual (OCR, PDF)]
* [http://w140.com/smb/7b92a_op_sm.pdf Tektronix 7B92A Operators Manual (OCR, PDF)]
* [http://w140.com/smb/7b92a_sm.pdf Tektronix 7B92A Service Manual (OCR, PDF)]
* [http://w140.com/smb/7b92a_sm.pdf Tektronix 7B92A Service Manual (OCR, PDF)]
}}
}}
The Tektronix 7B92 is a 500 MHz timebase plug-in for [[7000-series scopes]]. It was introduced along with the [[7904]] mainframe in 1972.
The '''Tektronix 7B92''' is a 500 MHz dual timebase plug-in for [[7000-series scopes]].  
It was introduced along with the [[7904]] mainframe in 1972.  In 1976, it was updated as the 7B92A.


The 7B92 uses a discrete trigger circuit containing [[tunnel diodes]].
An "HF Sync" triggering mode is provided in which the trigger level control varies the frequency of a built-in oscillator to lock on to the input for input signals from 100 to 500 MHz, providing higher sensitivity than the direct trigger (which is specified up to 500 MHz as well).


Up to serial number B069999, the 7B92A used a discrete trigger circuit.
Internal jumpers are provided to configure the 7B92 for operation in 7800/7900 vs. slower mainframes, and to select whether the variable control affects the delaying or the delayed time base.
After that, the 7B92A used a [[155-0061-00]] trigger amplifier followed by a
 
[[155-0150-00]] trigger detector.
As a dual time base, the 7B92 uses the top field in the [[7000 series readout system|display readout]] for the sweep speed of the main and the bottom field for the delayed time base. 
The delay time can only be read from the 10-turn analog dial.
 
The 7B92 has no magnifier function but its regular sweep dial setting reaches down to 500 ps/Div.  It has no provision for X-Y operation.


==Specifications==
{{BeginSpecs}}
{{BeginSpecs}}
{{Spec | Sweep speed | 0.5 ns/Div to 0.2 s/Div, 1—2—5 sequence (variable up to 0.5 s/Div)}}
{{Spec | Sweep speed | 0.5 ns/Div to 0.2 s/Div, 1—2—5 sequence (variable up to 0.5 s/Div)}}
Line 30: Line 36:
{{Spec | Ext Trig input | 1 MΩ // 20 pF or 50 Ω }}
{{Spec | Ext Trig input | 1 MΩ // 20 pF or 50 Ω }}
{{EndSpecs}}
{{EndSpecs}}
==Internals==
The 7B92 uses a discrete trigger circuit containing [[152-0177-02]] [[tunnel diodes]]. Up to serial number B069999, the 7B92A used a trigger circuit with [[155-0061-00]] amplifiers and [[152-0177-02]] tunnel diodes. After that, the 7B92A used a [[155-0061-00]] trigger amplifier followed by a [[155-0150-00]] trigger detector.
The 7B92A uses one other custom IC, the [[155-0049-00|155-0049-xx]] sweep control circuit. The internal jumper for mainframe selection (7800/7900/7100 vs. slower) actually increases the minimum holdoff time on the slower mainframe selection by adding a 214pF capacitor (C307 for 7B92, C835 for 7B92A) to pin 8 of the sweep control IC [[155-0049-00|155-0049-xx]] in parallel to the existing capacitors. This increases the minimum pulse width of the holdoff signal on [[7000_Series_plug-in_interface|pin B4]] so that the sweep logic of slower mainframes can handle it properly. The effect of this jumper is only noticeable for sweep speeds of 20 μs/Div. and faster, since there the smallest shunt capacitance is used on pin 8, and the holdoff time is minimal.
==Pictures==
==Pictures==


<gallery>
<gallery>
 
Tek 7b92 front.jpg    | 7B92 front
File:Tek 7b92 front.jpg    | 7B92 front
Tek 7b92 right.jpg    | 7B92 right
File:Tek 7b92 right.jpg    | 7B92 right
Tek 7b92 left.jpg    | 7B92 left
File:Tek 7b92 left.jpg    | 7B92 left
7b92a-front.jpg       | 7B92A front
File:Tek 7b92a front.jpg   | 7B92A front
Tek 7b92a front2.jpg| 7B92A
File:Tek 7b92a right.jpg  | 7B92A right
Tek 7b92a right.jpg  | 7B92A right
File:Tek 7b92a left.jpg    | 7B92A left
Tek 7b92a left.jpg    | 7B92A left
Image:Tek 7b92a block.png  | 7B92A block diagram
Tek 7b92a block.png  | 7B92A block diagram
7b92a-triggering-974mhz.jpg  | A 7B92A (B098xxx) triggering a 974 MHz sine applied to a [[7904]] mainframe via a 067-0587-02 calibration fixture (maximum triggerable frequency for this specimen).
Tek7904-7a19-7b92a-1010mhz-hfsync.jpg | A 7B92A (B098xxx) displaying a 1.01 GHz sine in HF Sync mode on a [[7904]] mainframe via a [[7A19]] amplifier (maximum signal generator frequency).
</gallery>
</gallery>


{{Custom ICs|7B92A}}


[[Category:7000 series horizontal plugins]]
[[Category:7000 series horizontal plugins]]

Revision as of 14:31, 20 August 2021

Manuals – Specifications – Links – Pictures

The Tektronix 7B92 is a 500 MHz dual timebase plug-in for 7000-series scopes. It was introduced along with the 7904 mainframe in 1972. In 1976, it was updated as the 7B92A.

An "HF Sync" triggering mode is provided in which the trigger level control varies the frequency of a built-in oscillator to lock on to the input for input signals from 100 to 500 MHz, providing higher sensitivity than the direct trigger (which is specified up to 500 MHz as well).

Internal jumpers are provided to configure the 7B92 for operation in 7800/7900 vs. slower mainframes, and to select whether the variable control affects the delaying or the delayed time base.

As a dual time base, the 7B92 uses the top field in the display readout for the sweep speed of the main and the bottom field for the delayed time base. The delay time can only be read from the 10-turn analog dial.

The 7B92 has no magnifier function but its regular sweep dial setting reaches down to 500 ps/Div. It has no provision for X-Y operation.

Key Specifications

Sweep speed 0.5 ns/Div to 0.2 s/Div, 1—2—5 sequence (variable up to 0.5 s/Div)
Delay time 0 to 9.9 Div
Triggering 0.5 Div or 100 mV up to 20 MHz, 1 Div or 500 mV up to 600 MHz
Jitter < 50 ps at 600 MHz
Ext Trig input 1 MΩ // 20 pF or 50 Ω

Internals

The 7B92 uses a discrete trigger circuit containing 152-0177-02 tunnel diodes. Up to serial number B069999, the 7B92A used a trigger circuit with 155-0061-00 amplifiers and 152-0177-02 tunnel diodes. After that, the 7B92A used a 155-0061-00 trigger amplifier followed by a 155-0150-00 trigger detector.

The 7B92A uses one other custom IC, the 155-0049-xx sweep control circuit. The internal jumper for mainframe selection (7800/7900/7100 vs. slower) actually increases the minimum holdoff time on the slower mainframe selection by adding a 214pF capacitor (C307 for 7B92, C835 for 7B92A) to pin 8 of the sweep control IC 155-0049-xx in parallel to the existing capacitors. This increases the minimum pulse width of the holdoff signal on pin B4 so that the sweep logic of slower mainframes can handle it properly. The effect of this jumper is only noticeable for sweep speeds of 20 μs/Div. and faster, since there the smallest shunt capacitance is used on pin 8, and the holdoff time is minimal.

Pictures

Custom ICs used in the 7B92A

Page Model Part nos Description Designers Used in
155-0049-00 M079G 155-0049-00 155-0049-01 155-0049-02 sweep control with lockout Bill DeVey 335 464 465 466 475 475A 475M 485 5B31 5B40 5B52 5B42 5B44 7B53A 7B80 7B85 7B87 7B92A 7B90P 7B10 7B15 SC502 7B42N AN/USM-281C 067-0657-00
155-0061-00 M083 155-0061-00 155-0061-01 155-0061-02 trigger amplifier Hans Springer 7B92 7B92A
155-0150-00 H473 155-0150-00 trigger detector Art Metz 7904A 7104 7B10 7B15 7B92A SCD1000