Difference between revisions of "L"

From TekWiki
Jump to navigation Jump to search
m
m (Circuit Summary)
Line 33: Line 33:
  
 
{{MissingSpecs}}
 
{{MissingSpecs}}
 +
 +
==Internals==
 +
 +
The input is switched via a Frequency compensated attenuator network which is controlled by the Vols/CM Switch.
 +
Input is then coupled to first cathode follower V5832, a 5654/6AK5W RF Pentode. This is configured as a cathode follower.
 +
The screen supply of this  cathode follower is switched from +100 to a decoupled network from +225V rail when the X10 Mode is selected.
 +
 +
The output of input amplifier is then switched via a 10X Amplifier - if the X10 mode is selected in the front panel - or directly to the paraphase or phase inverter made up of two [[12AU6]] tubes. This stage converts the input signal to a differential push-pull output. This output is passed to the final output drivers, which are two cathode follower sections with a pair of [[12AT7]] tubes. The differential output is then passed to pin 1 and 3 of the connector to drive the vertical amplifier inside the chassis.
 +
 +
The 10X amplifier stage is built with 3 5654/6AK5W tubes. First two are configured as amplifier and the last one as  output cathode follower.
 +
 +
Heater for the tubes are derived from +75VDC heater supply available at pin 15 of the connector. This is to avoid any  interference/hum from the regular AC heater supply at 60Hz.
  
 
==Pictures==
 
==Pictures==

Revision as of 08:55, 16 November 2019

Manuals – Specifications – Links – Pictures

The Tektronix Type L is an amplifier plug-in for 500-series scopes.

The Type L is a Type K plus a 10x-gain AC-coupled preamp that extends the maximum sensitivity to 5 mV/div. Bandwidth in a 545 is 30 MHz at 50 mV/div and above, 3 Hz-24 MHz at 20 mV/div and below.

Type 53/54L was introduced in 1957 along with the 536 and its companion 53/54T sweep plug-in. It was renamed the Type L in 1959. It was the fastest 5 mV plug-in until the 1A1 in 1964. It was dropped after 1972.

K, L, and T are tied for longest production life, at 16 years. B, D, and G are next at 15 years.

Late versions have a BNC connector instead of a UHF connector.

Lavoie Laboratories produced an unauthorized clone, the LA-265-L.

Specifications

please add

Internals

The input is switched via a Frequency compensated attenuator network which is controlled by the Vols/CM Switch. Input is then coupled to first cathode follower V5832, a 5654/6AK5W RF Pentode. This is configured as a cathode follower. The screen supply of this cathode follower is switched from +100 to a decoupled network from +225V rail when the X10 Mode is selected.

The output of input amplifier is then switched via a 10X Amplifier - if the X10 mode is selected in the front panel - or directly to the paraphase or phase inverter made up of two 12AU6 tubes. This stage converts the input signal to a differential push-pull output. This output is passed to the final output drivers, which are two cathode follower sections with a pair of 12AT7 tubes. The differential output is then passed to pin 1 and 3 of the connector to drive the vertical amplifier inside the chassis.

The 10X amplifier stage is built with 3 5654/6AK5W tubes. First two are configured as amplifier and the last one as output cathode follower.

Heater for the tubes are derived from +75VDC heater supply available at pin 15 of the connector. This is to avoid any interference/hum from the regular AC heater supply at 60Hz.

Pictures