M: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
(29 intermediate revisions by 5 users not shown)
Line 1: Line 1:
The Type M is a four-channel plug-in for [[500-series scopes]].
{{Plugin Sidebar 2 |
Early versions had UHF connectors for the inputs.   
title=Tektronix Type M|
Later versions have BNC connectors for the inputs.
summary=20 MHz quad channel amplifier|
The risetime is 17 nanoseconds, bandwidth is DC to 20MHz.  
image=Type m front.jpg |
Each input goes through a step attenuator, is clamped by a neon bulb,  
caption=Type M front view|
and then is fed to the grid of a cathode follower made with a [[7586]] Nuvistor tube.   
introduced=1962 |
discontinued=1973 |
series=[[500-series scopes]]|
manuals=
* [http://w140.com/mmm/tek-m.pdf Tektronix Type M Manual (PDF)]
* [http://bama.edebris.com/manuals/tek/m/ Tektronix Type M Manual (BAMA)]
<!-- * [http://w140.com/tek_fcp/tek_type_m_factory_cal_proc.pdf Tektronix Type M Factory Calibration Procedure (PDF)] -->
 
* [[Media:070-295.pdf|Tektronix Type M Manual (PDF, OCR, bad-OCR)]]
* [[Media:tek_type_m_fcp.pdf|Tektronix Type M Factory Calibration Procedure (PDF, OCR)]]
* [[Media:Tek type m cal outline.pdf|Tektronix Type M Calibration Outline (PDF, OCR)]]
}}
The '''Tektronix Type M''' is a four-channel plug-in for [[500-series scopes]].
It was designed by [[Oz Svehaug]] and [[Glenn Parks]].
Early versions had [[UHF connector]]s for the inputs.   
Later versions have [[BNC connector]]s for the inputs.
 
Type M was [[introduced in 1962]], along with the [[O|Type O]], and dropped after 1972.
 
{{MissingSpecs}}
 
The risetime is 17 nanoseconds, bandwidth is DC to 20 MHz.
Maximum sensitivity is 20 mV/div.
Each channel can be AC or DC coupled, inverted or straight, or disabled entirely.
The enabled channels can operate in CHOP or ALT mode.
 
==Internals==
Each input goes through a step attenuator,  
is clamped by a neon bulb,  
and then is fed to the grid of a cathode follower  
made with a [[7586]] Nuvistor tube.   
Next, the signal goes to a PNP differential amplifier.   
Next, the signal goes to a PNP differential amplifier.   
Diodes in series with the collector signal of this differential amplifier are used for input channel switching.
Diodes in series with the collector signal  
An internal differential signal bus connects the switched outputs of each of the input channels  
of this differential amplifier are used for input channel switching.
and feeds the signal to the output amplifier, which drives the signal output, pins 1 and 3 of the plug-in connector.   
An internal differential signal bus connects  
The output amplifier is two [[12AU6]] pentodes connected as a differential amplifier,  
the switched outputs of each of the input channels  
followed by a [[12AT7]] dual triode acting as a cathode follower to drive the output with a relatively low impedance.
and feeds the signal to the output amplifier,  
which drives pins 1 and 3 of the [[500-series plug-in connector]].   
The output amplifier is two [[12AU6]] pentodes  
connected as a differential amplifier,  
followed by a [[12AT7]] dual triode acting  
as a cathode follower to drive the output  
with a relatively low impedance.


* http://bama.edebris.com/manuals/tek/m/
==Pictures ==
* http://w140.com/tek_fcp/tek_type_m_factory_cal_proc.pdf


<gallery>
<gallery>
Image:Type_m_front.jpg|Front view.
Type_m_front.jpg|Late Type M Front view.
Image:Type_m_right.jpg|Right view
Type_m_left.jpg|Late Type M Left view.
Image:Type_m_left.jpg|Left view.
Type_m_right.jpg|Late Type M Right view
Tek_early_m_front.jpg|Early Type M Front
Tek early m left.jpg|Early Type M Left
Tek early m right.jpg|Early Type M Right
Tek m 501 1.jpg
Tek m 501 2.jpg
Tek m 501 3.jpg
Tek m 501 4.jpg
Tek m 501 5.jpg
Tek m 501 6.jpg
Tek m mod210d.jpg|Type M Mod 210D
Type m chan switching low sn.png|Channel Switching Schematic, sn 824 and below
Type m chan switching sn 825-up.png|Channel Switching Schematic, sn 825 and above
Type m 4 chan switched amp low sn.png|Four Channel Switched Amplifier Schematic, sn 2759 and below
Type m 4 chan switched amp sn 2760-up.png|Four Channel Switched Amplifier Schematic, sn 2760 and above
tek_type_m_in_556.jpg|Type M in [[556]]
</gallery>
</gallery>
[[Category:500 series plugins]]

Revision as of 11:14, 5 May 2021

Template:Plugin Sidebar 2 The Tektronix Type M is a four-channel plug-in for 500-series scopes. It was designed by Oz Svehaug and Glenn Parks. Early versions had UHF connectors for the inputs. Later versions have BNC connectors for the inputs.

Type M was introduced in 1962, along with the Type O, and dropped after 1972.

Key Specifications

  • please add

The risetime is 17 nanoseconds, bandwidth is DC to 20 MHz. Maximum sensitivity is 20 mV/div. Each channel can be AC or DC coupled, inverted or straight, or disabled entirely. The enabled channels can operate in CHOP or ALT mode.

Internals

Each input goes through a step attenuator, is clamped by a neon bulb, and then is fed to the grid of a cathode follower made with a 7586 Nuvistor tube. Next, the signal goes to a PNP differential amplifier. Diodes in series with the collector signal of this differential amplifier are used for input channel switching. An internal differential signal bus connects the switched outputs of each of the input channels and feeds the signal to the output amplifier, which drives pins 1 and 3 of the 500-series plug-in connector. The output amplifier is two 12AU6 pentodes connected as a differential amplifier, followed by a 12AT7 dual triode acting as a cathode follower to drive the output with a relatively low impedance.

Pictures