P: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
(One intermediate revision by the same user not shown)
Line 10: Line 10:
|designers=
|designers=
|manuals=
|manuals=
* [[Media:070-346.pdf|Tektronix Type P Manual]] (PDF, OCR)
* [[Media:070-346.pdf|Tektronix Type P Manual]] (OCR)
* [[Media:tek_type_p_fcp.pdf|Tektronix Type P Factory Calibration Procedure (PDF, OCR)]]
* [[Media:tek_type_p_fcp.pdf|Tektronix Type P Factory Calibration Procedure]] (OCR)
* [[Media:Tek type p irb.pdf|Tektronix Type P Instrument Reference Book (PDF, OCR)]]
* [[Media:Tek type p irb.pdf|Tektronix Type P Instrument Reference Book]] (OCR)
<!-- * [http://bama.edebris.com/manuals/tek/p/ Tektronix Type P Manual (PDF)]-->
<!-- * [http://w140.com/tek_fcp/tek_type_p_factory_cal_proc.pdf Tektronix Type P Factory Calibration Procedure (PDF)] -->
}}
}}
The '''Tektronix Type P''' plug-in is a calibration aid [[introduced in 1959]] for [[500-series scopes]] that applies a fast (4 nanosecond risetime) voltage step to the mainframe vertical amplifier via plug-in connector pins 1 and 3.   
The '''Tektronix Type P''' plug-in is a calibration aid [[introduced in 1959]] for [[500-series scopes]] that applies a fast (4 nanosecond risetime) voltage step to the mainframe vertical amplifier via plug-in connector pins 1 and 3.   
Line 38: Line 36:
Tek 53-54p inside.jpg|Type 53/54P
Tek 53-54p inside.jpg|Type 53/54P
</gallery>
</gallery>
{{Parts|P}}


[[Category:500 series plugins]]
[[Category:500 series plugins]]
[[Category:Calibration fixtures]]
[[Category:Calibration fixtures]]

Revision as of 05:18, 2 November 2022

Tektronix Type P
Calibration aid
Tek Type P

Compatible with 500-series scopes

Produced from 1959 to 1964

Manuals
Manuals – Specifications – Links – Pictures

The Tektronix Type P plug-in is a calibration aid introduced in 1959 for 500-series scopes that applies a fast (4 nanosecond risetime) voltage step to the mainframe vertical amplifier via plug-in connector pins 1 and 3.

Type P is designed to simulate a perfectly-adjusted Type K plug-in being driven by a Type 107 square-wave generator, and is used when adjusting the peaking coils and the delay line. The idea is to calibrate a mainframe using Type P, then use this mainframe and a 107 to calibrate other plug-ins.

The Type P does not contain any tubes, transistors, or tunnel diodes. It does contain a selenium rectifier and a mercury switch. The selenium rectifier in the Type P has four sections and full-wave rectifies the 6.3 VAC that is supplied by the scope mainframe on pins 13 and 14. The 120 Hz (assuming 60 Hz mains) component of the full-wave rectified waveform is applied to the coil of the mercury switch to drive the opening and closing of the contacts. An adjustable fraction of the DC component of the full-wave rectified waveform is applied to the coil of the mercury switch to create a constant component in the magnetic field to bias the switch contacts to the best operating point.

The Type P was the only new plug-in for 1959, except for the upgrade from Type 53/54C to Type CA. It was dropped after 1963, replaced by the TU-7.

Pictures


Some Parts Used in the P