TM5000 Series plug-in interface: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
(added tolerance to regulated DC voltages from TM5006 manual; explained compatability of TM500 plugins in TM5000 mainframes)
Line 5: Line 5:
There are two dedicated, floating 25 V<sub>AC</sub> transformer windings per slot, as well as several AC and DC buses shared by all slots.<br />
There are two dedicated, floating 25 V<sub>AC</sub> transformer windings per slot, as well as several AC and DC buses shared by all slots.<br />
For each slot, two uncommitted transistors (one NPN and one PNP) are mounted in the mainframe. These are available for the module's power regulation circuits.
For each slot, two uncommitted transistors (one NPN and one PNP) are mounted in the mainframe. These are available for the module's power regulation circuits.
Whereas TM500 mainframes supply filtered, unregulated DC voltages, in TM5000 units a switch-mode power supply feeds the DC rails.
 
Whereas TM500 mainframes supply filtered, unregulated DC voltages, in TM5000 units a switch-mode power supply feeds the DC rails and provides regulated voltages. These voltages are lower than the ones specified for TM500 mainframes, but the lowest specified supply voltages coincide, ensuring full backwards compatibility of TM500 plugins when operated in TM5000 mainframes.


The signal pin connections depend on the individual modules.  For details, please see the [[Media:070-2088-00.pdf|TM 500 Rear Interface Data Book]].
The signal pin connections depend on the individual modules.  For details, please see the [[Media:070-2088-00.pdf|TM 500 Rear Interface Data Book]].
Line 23: Line 24:
| 13 || 25 V<sub>AC</sub> winding #1 || 25 V<sub>AC</sub> winding #1
| 13 || 25 V<sub>AC</sub> winding #1 || 25 V<sub>AC</sub> winding #1
|- bgcolor="Pink"  
|- bgcolor="Pink"  
| 12 || +26 V<sub>DC</sub> || +26 V<sub>DC</sub>
| 12 || +26 V<sub>DC</sub> ±2.3 V || +26 V<sub>DC</sub> ±2.3 V
|- bgcolor="LightGreen"
|- bgcolor="LightGreen"
| 11 || Collector lead of PNP series pass || Base lead of PNP series pass
| 11 || Collector lead of PNP series pass || Base lead of PNP series pass
Line 31: Line 32:
| 9 || Ground || Ground
| 9 || Ground || Ground
|- bgcolor="Pink"  
|- bgcolor="Pink"  
| 8 || −26 V<sub>DC</sub> || −26 V<sub>DC</sub>
| 8 || −26 V<sub>DC</sub> ±2.3 V || −26 V<sub>DC</sub> ±2.3 V
|- bgcolor="LightGreen"
|- bgcolor="LightGreen"
| 7 || Collector lead of NPN series pass || Emitter lead of NPN series pass
| 7 || Collector lead of NPN series pass || Emitter lead of NPN series pass
Line 45: Line 46:
| 3 || Ground  || Ground  
| 3 || Ground  || Ground  
|- bgcolor="Pink"  
|- bgcolor="Pink"  
| 2 || +8 V filtered DC || +8 V filtered DC
| 2 || +8 V<sub>DC</sub>  +0.5/-0.4 V || +8 V<sub>DC</sub>  +0.5/-0.4 V
|- bgcolor="LightBlue"  
|- bgcolor="LightBlue"  
| 1 || 25 V<sub>AC</sub> winding #2 || 25 V<sub>AC</sub> winding #2
| 1 || 25 V<sub>AC</sub> winding #2 || 25 V<sub>AC</sub> winding #2

Revision as of 17:57, 7 December 2020

Tektronix TM5000 mainframes provide power supplies and signal connections for TM5000 plug-ins.

Mechanically, the main interface is a direct card-edge connector with 28 contacts on either side (numbered from 1 at the bottom to 28 on the top) at 5/32" (~0.156" or 3.96 mm) spacing. The connector can be keyed in several places, the plug-in boards have matching cuts between contacts (see below). An additional 20-contact card edge connector carries the GPIB signals.

There are two dedicated, floating 25 VAC transformer windings per slot, as well as several AC and DC buses shared by all slots.
For each slot, two uncommitted transistors (one NPN and one PNP) are mounted in the mainframe. These are available for the module's power regulation circuits.

Whereas TM500 mainframes supply filtered, unregulated DC voltages, in TM5000 units a switch-mode power supply feeds the DC rails and provides regulated voltages. These voltages are lower than the ones specified for TM500 mainframes, but the lowest specified supply voltages coincide, ensuring full backwards compatibility of TM500 plugins when operated in TM5000 mainframes.

The signal pin connections depend on the individual modules. For details, please see the TM 500 Rear Interface Data Book.

  B side A side
Pin Function Function
28..14 Signals Signals
13 25 VAC winding #1 25 VAC winding #1
12 +26 VDC ±2.3 V +26 VDC ±2.3 V
11 Collector lead of PNP series pass Base lead of PNP series pass
10 Transformer shield lead Emitter lead of PNP series pass
9 Ground Ground
8 −26 VDC ±2.3 V −26 VDC ±2.3 V
7 Collector lead of NPN series pass Emitter lead of NPN series pass
6 PWR Base lead of NPN series pass
5 17.5 VAC winding 17.5 VAC winding
4 Ground Ground
3 Ground Ground
2 +8 VDC +0.5/-0.4 V +8 VDC +0.5/-0.4 V
1 25 VAC winding #2 25 VAC winding #2

Interface connections viewed from rear of power module. Pins 14 through 28 are used for signal connections.

Pin group function legend

 DC power and ground
 AC power 
 Signals  
 Uncommitted transistors

Used in

See also