User:Peter: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 58: Line 58:
Tek-017-067.jpg            | [[109|017-067]]
Tek-017-067.jpg            | [[109|017-067]]
Tek134-front-2.jpg        | [[134]]
Tek134-front-2.jpg        | [[134]]
</gallery>
P6022+term.jpg            | [[P6022]]
</gallery>  


===Screen shots===
===Screen shots===
Line 118: Line 119:
P6021-6022-1000hz.jpg | P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mA<sub>p-p</sub>, 1 kHz
P6021-6022-1000hz.jpg | P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mA<sub>p-p</sub>, 1 kHz
P6021-6022-10000hz.jpg | P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mA<sub>p-p</sub>, 10 kHz
P6021-6022-10000hz.jpg | P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mA<sub>p-p</sub>, 10 kHz
P6021-bat41-1.jpg | Measuring diode reverse recovery
P6021-bat41-2.jpg | BAT41 diode reverse recovery, 20 mA/Div
</gallery>
</gallery>

Revision as of 07:05, 26 October 2016

Scopes

Plugins

Probes and other gear

Screen shots

  • Faster-than-light beam on 7104? Using a 067-0587-02 calibration fixture at maximum amplitude produces this trace spanning 1.2 Div horizontally at 200 ps/Div and 8 Div vertically. Trace length is (1.2² + 8²)½ × 8.5 mm = 68.8 mm, travelled in 1.2 × 200 ps = 240 ps. Apparent speed is therefore 68.8×10-3 / 240×10-12 m/s or 2.86×108 m/s. Very near miss ...

    Faster-than-light beam on 7104? Using a 067-0587-02 calibration fixture at maximum amplitude produces this trace spanning 1.2 Div horizontally at 200 ps/Div and 8 Div vertically. Trace length is (1.2² + 8²)½ × 8.5 mm = 68.8 mm, travelled in 1.2 × 200 ps = 240 ps. Apparent speed is therefore 68.8×10-3 / 240×10-12 m/s or 2.86×108 m/s. Very near miss ...

  • Rise time measurement. 150 ps risetime pulse from 067-0587-02 at 100 Hz repetition rate. Measured 240 ps (corrected for 150 ps fixture rise time: 190 ns = 1.8 GHz)

    Rise time measurement. 150 ps risetime pulse from 067-0587-02 at 100 Hz repetition rate. Measured 240 ps (corrected for 150 ps fixture rise time: 190 ns = 1.8 GHz)

  • Rise time measurement as before, 1000 Hz repetition rate at same brightness settings.

    Rise time measurement as before, 1000 Hz repetition rate at same brightness settings.

  • 7104 recording a single shot pulse (from 067-0587-02) at 200 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed.

    7104 recording a single shot pulse (from 067-0587-02) at 200 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed.

  • 7104 recording 1 GHz sine, single shot at 500 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed. CRT amplification loss is evident around the center line.

    7104 recording 1 GHz sine, single shot at 500 ps/Div. Camera: Nikon D7000, 50 mm f/1.4, ISO 3200, 1/2 s. CRT filter not removed. CRT amplification loss is evident around the center line.

  • BC337 on 7CT1N

    BC337 on 7CT1N

  • P6202 rise time

    P6202 rise time

  • P6202 rise time

    P6202 rise time

  • P6230 Rise time measured on a 7S12 with S-52 and S-4 heads, P6230 ground sleeve connected directly at S-52 output (no ground lead)

    P6230 Rise time measured on a 7S12 with S-52 and S-4 heads, P6230 ground sleeve connected directly at S-52 output (no ground lead)

  • P6230 Rise time without ground lead: 9.2 * 20 ps = 184 ps (equiv. to 1.9 GHz bandwidth)

    P6230 Rise time without ground lead: 9.2 * 20 ps = 184 ps (equiv. to 1.9 GHz bandwidth)

  • P6230 Rise time - Effect of using the "low inductance" ground lead - rise time 400 ps, bandwidth 875 MHz

    P6230 Rise time - Effect of using the "low inductance" ground lead - rise time 400 ps, bandwidth 875 MHz

  • P6230 Rise time - Using the 250 mm alligator ground lead - severe pulse distortion, rise time ~3 ns (115 MHz)!

    P6230 Rise time - Using the 250 mm alligator ground lead - severe pulse distortion, rise time ~3 ns (115 MHz)!

  • A 7B92A (B098xxx) displaying a 1.01 GHz sine in HF Sync mode (7904 mainframe, 7A19 amplifier)

    A 7B92A (B098xxx) displaying a 1.01 GHz sine in HF Sync mode (7904 mainframe, 7A19 amplifier)

  • A 7B92A (B098xxx) triggering a 974 MHz sine applied via 067-0587-02 calibration fixture

    A 7B92A (B098xxx) triggering a 974 MHz sine applied via 067-0587-02 calibration fixture

  • Classic readout board diagnostic display

    Classic readout board diagnostic display

  • 15 μVp-ptriangle wave measured through 7A22. Using variable-persistence storage mode on a 7613 for noise filtering.

    15 μVp-ptriangle wave measured through 7A22. Using variable-persistence storage mode on a 7613 for noise filtering.

  • Tektronix 067-0587-02, gain mode, in horizontal slot

    Tektronix 067-0587-02, gain mode, in horizontal slot

  • Tektronix 067-0587-02, gain mode, in vertical slot

    Tektronix 067-0587-02, gain mode, in vertical slot

  • 7D14 screen picture - 500 MHz signal (7A19, 7B92A, 7904)

    7D14 screen picture - 500 MHz signal (7A19, 7B92A, 7904)

  • 7B85 used for rise time measurement

    7B85 used for rise time measurement

  • 7B85 used for rise time measurement

    7B85 used for rise time measurement

  • 7B85 used for pulse width measurement

    7B85 used for pulse width measurement

  • 7B85 used for pulse period measurement

    7B85 used for pulse period measurement

  • 7B85 used for pulse period measurement

    7B85 used for pulse period measurement

  • 7S11/7T11, 1 GHz sine, smooth mode, on variable-persistence storage scope (7613)

    7S11/7T11, 1 GHz sine, smooth mode, on variable-persistence storage scope (7613)

  • 7S11/7T11, 1 GHz sine, smooth mode

    7S11/7T11, 1 GHz sine, smooth mode

  • 7S11/7T11, 1 GHz sine, normal mode

    7S11/7T11, 1 GHz sine, normal mode

  • 7S11/S-4 and 7T11A displaying 1 GHz sine

    7S11/S-4 and 7T11A displaying 1 GHz sine

  • 7S12 as a sampler displaying a 1 GHz signal (hi-res mode / storage)

    7S12 as a sampler displaying a 1 GHz signal (hi-res mode / storage)

  • 7S12 as a sampler displaying a 1 GHz signal (hi-res mode / storage)

    7S12 as a sampler displaying a 1 GHz signal (hi-res mode / storage)

  • 7S12 as a sampler displaying a 1 GHz signal (normal mode / non-storage)

    7S12 as a sampler displaying a 1 GHz signal (normal mode / non-storage)

  • 7S12 displaying the incident pulse from an S-52 (nom. < 25 ps) through an S-6 head (nom. < 30 ps)

    7S12 displaying the incident pulse from an S-52 (nom. < 25 ps) through an S-6 head (nom. < 30 ps)

  • 7S12/S-6/S-52 "Self Portrait" - pulse reflected on S-6 "through" path (approx. 120 ps one way)

    7S12/S-6/S-52 "Self Portrait" - pulse reflected on S-6 "through" path (approx. 120 ps one way)

  • Full pulse pattern of a 7S12/S-52 in real time (top trace) and sampled (bottom trace) shown simultaneously on 7844. 7S12 trace at slowest possible sweep.

    Full pulse pattern of a 7S12/S-52 in real time (top trace) and sampled (bottom trace) shown simultaneously on 7844. 7S12 trace at slowest possible sweep.

  • S-52 pulse in real time (top trace) and sampled (bottom trace) shown simultaneously on 7844. Approximately equal time scales.

    S-52 pulse in real time (top trace) and sampled (bottom trace) shown simultaneously on 7844. Approximately equal time scales.

  • sub-millivolt triangle signal displayed through 7A22, BW=1 kHz

    sub-millivolt triangle signal displayed through 7A22, BW=1 kHz

  • sub-millivolt triangle signal displayed through 7A22, BW=10 kHz

    sub-millivolt triangle signal displayed through 7A22, BW=10 kHz

  • sub-millivolt triangle signal displayed through 7A22, BW=100 kHz

    sub-millivolt triangle signal displayed through 7A22, BW=100 kHz

  • sub-millivolt triangle signal through 7A22, BW=1 MHz

    sub-millivolt triangle signal through 7A22, BW=1 MHz

  • P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 100 Hz

    P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 100 Hz

  • P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 1 kHz

    P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 1 kHz

  • P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 10 kHz

    P6022 / passive term. @ 10 mA/Div (top) vs. P6021+134 (bottom), sawtooth @ 100 mAp-p, 10 kHz

  • Measuring diode reverse recovery

    Measuring diode reverse recovery

  • BAT41 diode reverse recovery, 20 mA/Div

    BAT41 diode reverse recovery, 20 mA/Div

Retrieved from "https://w140.com/tekwiki/index.php?title=User:Peter&oldid=22989"