555: Difference between revisions

Revision as of 21:30, 6 May 2013

The Tektronix Type 555 is a dual-beam CRT oscilloscope introduced by Tektronix in 1959 and made until the late 1960's, when it was replaced by the 556. The system is split across two pieces: the main indicator unit and the external power supply unit. The power supply unit contains the main transformer, rectifiers and regulators for all of the voltages except the filament and CRT HV supplies. The filament and CRT HV voltages are generated in the 555 indicator unit.

The 555 takes two letter-series or 1-series vertical plug-ins

Type 21 and 22 Timebases

The 555 uses special horizontal plug-ins that contain the trigger and sweep. Early instances of the 555 came with the 21 and 22 horizontal plug-ins.

Type 21A and 22A Timebases

Later instances came with the 21A and 22A horizontal plug-ins, which use tunnel diodes for triggering. Delayed triggering is supported. Since the 555 is a dual-beam scope, it is also possible to start one of the sweeps while the other beam is sweeping. The upper-beam sweep and lower-beam sweeps are, in fact, totally independent.

Filament Supply Regulator

Regulation of the filament supply happens as follows: There is a feedback loop that is formed between the indicator unit and the power supply unit. The power supply sends AC through the interconnection cable to the indicator unit, where it is connected to the primary of the filament transformer. A sample of the output of the filament transformer is sent back through the interconnection cable from the indicator unit to the power supply unit. This performs two functions. First, the filament voltage that is sent back to the power supply unit is used to heat the cathodes of tubes in the power supply unit. Second, this filament voltage is the feedback signal to a regulator in the power supply unit that controls how much voltage is sent to the filament transformer. One of the consequences of this scheme is that it is impossible to energize the power supply unit without the indicator unit connected. The regulator tubes in the power supply would remain cold without filament power, and would not pass any current.

Vertical Amplifier

The 555 has a six-section differential distributed vertical output amplifier made of 6DK6 tubes. It is the same as the vertical output amplifier in the 551 and the 545A. An L-C delay line is between the vertical output amplifier and the CRT vertical deflection plates for each channel.

Architecturally, the 555, with its four plug-ins, is similar to the 7844.

front view: two timing plug-ins on top and two vertical plug-ins on bottom
external power supply
left side view
right side view
top view
555 with P11-option
555 with P7-option (fast blue and slow green Phosphor)
Power interconnect
Power interconnect
Power interconnect
timebase interconnect
555 block diagram
lower beam vertical amplifier
power interconnect
heater regulator
Type 21 trigger
block diagram
CRT
CRT
CRT
CRT
CRT
CRT
22A front
22A TD trigger board
22A top
22A bottom
21 front
21 top
21 bottom
22 front
22 top
22 bottom
21A front
21A top
21 bottom
21A TD trigger board

@@ Line 12: / Line 12: @@
 [[letter-series and 1-series plug-ins|letter-series or 1-series vertical plug-ins]]
+== Type 21 and 22 Timebases ==
 The 555 uses special horizontal plug-ins that contain the trigger and sweep.
 Early instances of the 555 came with
 the 21 and 22 horizontal plug-ins.
+== Type 21A and 22A Timebases ==
 Later instances came with
 the 21A and 22A horizontal plug-ins,
@@ Line 23: / Line 26: @@
 The upper-beam sweep and lower-beam sweeps are, in fact, totally independent.
+== Filament Supply Regulator ==
 Regulation of the filament supply happens as follows:
 There is a feedback loop that is formed between the indicator
@@ Line 40: / Line 44: @@
 would remain cold without filament power, and would not pass any current.
+== Vertical Amplifier ==
 The 555 has a six-section differential
 [[distributed amplifier|distributed vertical output amplifier]]