556: Difference between revisions

Revision as of 06:58, 27 October 2014

{{{manufacturer}}}
50 MHz dual beam scope Tektronix 556 front Produced from 1966 to (?) Manuals Tektronix 556 Manual (PDF) (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 556 is a dual-beam scope, the successor to the Tektronix 555. It uses letter-series and 1-series plug-ins. A rack-mount version, the RM556 also exists. The 556, which is wider than the average 500-series scope, fits in the 205 cart.

Dual-Beam Modes

The 556 is a true dual-beam scope and none of the signal path is shared between the two beams. Electrically speaking, the power supply and the calibrator are the only parts that are common to both beams. The 556 has almost complete left-right symmetry, corresponding to upper and lower beams. Although the beams can be operated completely independently, the 556 provides many options for routing signals between the vertical plug-ins, triggers, sweeps, horizontal and vertical amplifiers. For example, a common use for a 556 is to view two simultaneous single-shot events, both sweeps being triggered by one of the traces. For this purpose, the 556 allows the output of one sweep generator to be routed to the horizontal amplifier of the other beam, so it drives both beams. Many other more sophisticated modes are also available.

Triggering

The triggering in the 556 is done using tunnel diodes and the trigger circuit sits on its own small PC board just behind the trigger source selection switch.

Vertical Amplifiers

The vertical amplifier of the 556 is solid state except for the input cathode followers (12AT7) and and the output stage (8608).

CRT Circuit

The CRT circuit of the 556 uses two HV transformers. The lower beam transformer, T1301, produces:

CRT anode voltage: +8150V
lower beam cathode voltage: -1850V
lower beam control grid (blanking) voltage: varies, about -2000V

The upper beam transformer, T1351, produces:

upper beam cathode voltage: -1850V
upper beam control grid (blanking) voltage: varies, about -2000V

Comparison with the 555

The 556 is a one-piece unit whereas the 555 has a the power supply in a separate box. Triggering and sweep circuitry is integrated into the 556 mainframe, as opposed to the removable timing units in the 555. The 556 takes two letter-series or 1-series vertical plug-ins. The 556's bandwidth is 50MHz, whereas the 555's is 30.

Comparison with the 565

The 556 superficially resembles the 565, which is is also a dual-beam one-piece scope, but the 565 takes two 2-series or 3-series vertical plug-ins and has much lower vertical and trigger bandwidth.

Pictures

Front panel of a 556.
Front view of an RM556.
Trigger board contains two tunnel diodes and a reed relay.
Top view.
Top view of RM556.
Right side view.
Bottom view.
Bottom view with power supply/calibrator/delay pickoff chassis swung out.
Output amplifier driving deflection plates.
Neck of 556 CRT. The tube contains two electrically independent guns and vertical and horizontal deflection plates.
Rear view
Vertical amp schematic
CRT Circuit

@@ Line 24: / Line 24: @@
 The vertical amplifier of the 556 is solid state except for the input cathode followers ([[12AT7]]) and and the
 output stage ([[8608]]).
+== CRT Circuit ==
+The CRT circuit of the 556 uses two HV transformers.
+The lower beam transformer, T1301, produces:
+* CRT anode voltage: +8150V
+* lower beam cathode voltage: -1850V
+* lower beam control grid (blanking) voltage: varies, about -2000V
+The upper beam transformer, T1351, produces:
+* upper beam cathode voltage: -1850V
+* upper beam control grid (blanking) voltage: varies, about -2000V
 == Comparison with the 555 ==