1,869
edits
No edit summary |
No edit summary |
||
(17 intermediate revisions by 2 users not shown) | |||
Line 1: | Line 1: | ||
{{Plugin Sidebar 2| | |||
title=Tektronix S-1 | | |||
summary=Sampling Head | | |||
image=S1-crop.jpg | | |||
caption=S-1 head | | |||
introduced=1967 | | |||
discontinued=1989 | | |||
series={{3S+7S}} | | |||
manuals= | |||
* [http://bama.edebris.com/download/tek/s1/s1.djvu Tektronix S-1 Manual (DjVu)] | * [http://bama.edebris.com/download/tek/s1/s1.djvu Tektronix S-1 Manual (DjVu)] | ||
* [http://w140.com/tek_s1.pdf Tektronix S-1 Manual (PDF)] | * [http://w140.com/tek_s1.pdf Tektronix S-1 Manual (PDF)] | ||
}} | |||
The '''S-1 sampling plug-in head''' provides a single [[GR-874]] 50 Ω input with a 350 ps rise-time. | |||
The S-1 can be used with the 7000 series of [[sampling_oscilloscope|sampling]] plug-ins, as well as the 3S series of sampling units. | |||
{{BeginSpecs}} | |||
{{Spec | Rise time | 350 ps }} | |||
{{Spec | Bandwidth | 1 GHz }} | |||
{{Spec | Input amplitude | −1 V to +1 V with ≤1 V<sub>p-p</sub> signals }} | |||
{{Spec | Maximum input | ±5 V<sub>DC</sub> or sine of 10 V<sub>p-p</sub> up to 10 MHz }} | |||
{{Spec | Input impedance | 50 Ω ([[GR-874]]) }} | |||
{{Spec | Noise | < 2 mV }} | |||
{{Spec | Features | trigger pickoff for internal triggering }} | |||
{{EndSpecs}} | |||
==Links== | |||
* [http://www.amplifier.cd/Test_Equipment/Tektronix/Tektronix_7000_series_special/S-1.html S-1 page @ amplifier.cd] | |||
==Internals== | |||
The S-1 uses a two-diode sampling gate which has relatively high "kick-out" (leakage of the strobe signal out of the input). | |||
The manual cautions, | |||
<blockquote> | |||
Operating the sampling head without the input connector terminated by a 50 Ω resistor or coaxial | |||
cable will cause a vertical shift of the zero signal baseline by a few millivolts. This is caused by the | |||
strobe kickout signal being reflected from the open input connector, and arriving back at the sampling | |||
bridge while the bridge is conducting. | |||
</blockquote> | |||
The sampling bridge strobe signal is generated by an [[avalanche transistor]] followed by a [[step recovery diode]]. | |||
==Pictures== | |||
<gallery> | <gallery> | ||
Tek s-1.jpg | |||
Tek s1 internal strobe.jpg | Strobe board | |||
Tek s1 internal pre.jpg | Preamp board | |||
Tek s1 front.jpg | S-1 front | |||
S1 diode.jpg | Diode mount in S-1 | |||
S1 diode2.jpg | Diode mount in S-1 | |||
S1 diode3.jpg | Diode mount in S-1 | |||
S-52_s-1_rt_brighter.jpg | S-1 in a [[3S2]] sampler / [[567]] scope | |||
Tek s1 sampler schematic.png|Tektronix S-1 sampler | |||
Tek 7s11 s-1.jpg|[[7S11]] with S-1 | |||
</gallery> | </gallery> | ||
[[Category:7000 and 3S series sampling heads]] | |||
[[Category:GR874]] |
edits