TekWiki

7000 series readout system: Difference between revisions

Page Discussion Repairs

7000 series readout system (view source)

Revision as of 11:41, 28 February 2015

1,374 bytes added ,  28 February 2015
modes chapter
(modes chapter)
Line 3: Line 3:
The design ultimately selected for the 7000 series was proposed and designed by [[Barrie Gilbert]].  It uses the CRT beam to display annotations in the same focal plane as the scope's main display.
The design ultimately selected for the 7000 series was proposed and designed by [[Barrie Gilbert]].  It uses the CRT beam to display annotations in the same focal plane as the scope's main display.


==Layout==
==Concept==
 
===Layout===
[[File:Tek7000-readout-positions.jpg|thumb|right|200px|screen layout]]
[[File:Tek7000-readout-positions.jpg|thumb|right|200px|screen layout]]
A total of eight display fields can be superimposed on the CRT picture, four on top and four at the bottom.  These are logically associated with the four possible slots in full-size mainframes, with the top field corresponding to the first channel, primary time base or primary function of a plug-in, and the bottom field corresponding to a second channel, delayed timebase, secondary function or unit label.
A total of eight display fields can be superimposed on the CRT picture, four on top and four at the bottom.  These are logically associated with the four possible slots in full-size mainframes, with the top field corresponding to the first channel, primary time base or primary function of a plug-in, and the bottom field corresponding to a second channel, delayed timebase, secondary function or unit label.


==Mainframe circuit==
===Readout modes===
[[File:tek_readout_beam.jpg|thumb|right|200px|Signal beam interruption by readout seen on beam 2 of a [[7844]]]]
The standard mode of operation for the readout is free-running, i.e. in regular intervals that are asynchronous to the sweep, beam control is switched to the readout generator.  In certain conditions, this can cause visible gaps in the signal display.  When the readout intensity control is turned to minimum, this switching is disabled and the signal trace is not interrupted at all.
 
A sliding switch on the analog ROM readout board (internal to the scope) allows the operator to select "gate triggered" mode, in which the readout signal is produced only after a sweep has occurred.  The advantage of this mode is that the beam is not interrupted while drawing the signal, however, if no sweep occurs there is no readout, and if the sweep is slow, the readout flickers.
 
In certain mainframes such as the [[7844]], [[7904A]] and [[7104]], turning the display intensity control past the maximum intensity setting switches readout into pulsed mode.
Depending on a second switch, readout occurs at the end of the sweep ("+ GATE") or when triggered by a back-panel "Graticule/Readout Single Shot" input.  These scopes also have a "manual readout" button and similar controls for pulsed graticule illumination.


===Scanning===
===Scanning===
Line 13: Line 22:


Two output lines, row and column, are connected from each channel (two channels per plug-in compartment) back to the oscilloscope readout system.  Data is encoded on these output lines as a pair of ten-level analog current sequences (in 100 μA steps from 0 to 1 mA), which can address a matrix of 10 × 10 positions.  In this matrix, rows 1, 2, 4, 5 and 6 correspond to characters whereas others are used to encode instructions:
Two output lines, row and column, are connected from each channel (two channels per plug-in compartment) back to the oscilloscope readout system.  Data is encoded on these output lines as a pair of ten-level analog current sequences (in 100 μA steps from 0 to 1 mA), which can address a matrix of 10 × 10 positions.  In this matrix, rows 1, 2, 4, 5 and 6 correspond to characters whereas others are used to encode instructions:
[[File:Tek7000-readout-charset.jpg|600px]]
[[File:Tek7000-readout-charset.jpg|center|600px]]


[[File:7000-readout-chargen-positions.jpg|thumb|300px|right|Character generator matrix positions in 7000 series readout analog character generator ROM]]
In time slot 1, special operations can be requested that affect the display in later time slots. These commands are designed to simplify display changes required by external probes that request beam identification or change input sensitivity.  The "Identify" command switches to an internal program displaying IDENTIFY instead of any encoded value.  Command R3/C1 requests an additional zero to be added starting in time slot 5, R3/C2 adds two such zeroes, R3/C3 shifts the selected prefix one code to the left (i.e. p → n, n → μ, μ → m, m → space), and R3/C4 shifts the prefix and adds a zero.  (See the [[Media:Tek-plugin-readout.jpg|encoding circuit of the 7A18 plugin]] for an example implementation.)  It is also possible to request a decimal point to be drawn without losing display digits, by encoding row 7 commands in time slot 1.
In time slot 1, special operations can be requested that affect the display in later time slots. These commands are designed to simplify display changes required by external probes that request beam identification or change input sensitivity.  The "Identify" command switches to an internal program displaying IDENTIFY instead of any encoded value.  Command R3/C1 requests an additional zero to be added starting in time slot 5, R3/C2 adds two such zeroes, R3/C3 shifts the selected prefix one code to the left (i.e. p → n, n → μ, μ → m, m → space), and R3/C4 shifts the prefix and adds a zero.  (See the [[Media:Tek-plugin-readout.jpg|encoding circuit of the 7A18 plugin]] for an example implementation.)  It is also possible to request a decimal point to be drawn without losing display digits, by encoding row 7 commands in time slot 1.


===Character generation===
===Plug-in circuit===
The character generators are custom analog chips that provide X and Y output currents for ten characters of up to seven strokes (eight X/Y coordinate pairs) inscribing each character.  The in-character coordinate points are selected through a triangular analog signal, not a digital code, which in turn activates one of eight groups of three transistors each generating the X/Y output currents.  Each of these groups is fed a constant emitter current (I<sub>E</sub>), and the distribution of this current to the three transistors is controlled by their different emitter areas.  The first and second collectors provide X and Y currents respectively, the third ("Z") directs current to the substrate (I<sub>E</sub> - I<sub>X</sub> - I<sub>Y</sub> - I<sub>Z</sub> = 0).  Actually, the emitter area itself is not varied in the mask, but out of a fixed number of emitters of equal size, a certain number is connected on each transistor:  [[File:7000-readout-chargen-circuit-1.jpg|300px|thumb|ROM circuit for one character (digit "3"). Bases are scanned in turn.  The numbers under the emitters indicate how many of the emitters are connected to the common rail. Ten such character circuits plus the scanning (base drive) circuit are integrated in each ROM chip.  All X and Y collector outputs are connected across characters and chips.]]
[[File:Tek-readout-simple-encoder.jpg|400px|left|Simple readout encoding circuit. Switch positions shown create readout of "100 μV". (Click for full size.)]]
If the bases were controlled by a digital decoder, only one triplet of transistors would be active at any time and only points would be generated on the display.  Instead, through an analog driving circuit, gradual cut-over is achieved, i.e. current from one group is reduced while that from the next group is increased, and a linear transition from the first to the second X/Y coordinate pair is displayed as a stroke on the CRT.  The actual shape of the base drive voltages has great influence on the proper character rendering (this is explained at length in Gilbert's 1971 SSC paper).
 
==Plug-in circuit==
 
A plug-in encodes the desired read-out information either by connecting resistors between the output lines and the time-slot input lines, or by generating equivalent currents.  
A plug-in encodes the desired read-out information either by connecting resistors between the output lines and the time-slot input lines, or by generating equivalent currents.  


A simple plug-in such as a vertical amplifier will only require a small number of resistors and possibly diodes in addition to a suitably coded switch.  
A simple plug-in such as a vertical amplifier will only require a small number of resistors and possibly diodes in addition to a suitably coded switch.  
It will use TS1 to encode the number of zeros, TS2 to display a down-arrow indicating an inverted input, TS3 to display ">" or "<" if the input is uncalibrated, TS4 for a digit, TS8 for a unit prefix like "μ" and TS9 for a unit like "V".  The other slots are unused:
It will use TS1 to encode the number of zeros, TS2 to display a down-arrow indicating an inverted input, TS3 to display ">" or "<" if the input is uncalibrated, TS4 for a digit, TS8 for a unit prefix like "μ" and TS9 for a unit like "V".  The other slots are unused:
[[File:Tek-readout-simple-encoder.jpg|600px|Simple readout encoding circuit. Switch positions shown create readout of "100 μV". (Click for full size.)]]


==Complex plugins==
===Probe interface===
 
Most 7000 series plugins have rings around the BNC input sockets that allow attached probes to interface with the readout system.  The probe connector includes a contact pin connecting this ring.  A resistor connected to ground encodes the probe attenuation, e.g. 11 kΩ indicates a x10 probe.  If the probe includes an Identify switch at the tip, this connects the readout pin directly to ground.The [[Media:Tek-plugin-readout.jpg|plug-in circuit]] uses the shift instructions in time slot 1 to implement the change of range.
 
===Complex plugins===
The [[7M13]] plugin allows the user to encode arbitrary text and numbers plus an optional picture counter value, for photographic documentation.
The [[7M13]] plugin allows the user to encode arbitrary text and numbers plus an optional picture counter value, for photographic documentation.


Line 37: Line 44:
The [[067-0905-99]] "Readout Exerciser" is a test fixture for the readout system.
The [[067-0905-99]] "Readout Exerciser" is a test fixture for the readout system.


==Probe interface==


Most 7000 series plugins have rings around the BNC input sockets that allow attached probes to interface with the readout system.  The probe connector includes a contact pin connecting this ring.  A resistor connected to ground encodes the probe attenuation, e.g. 11 kΩ indicates a x10 probe.  If the probe includes an Identify switch at the tip, this connects the readout pin directly to ground.The [[Media:Tek-plugin-readout.jpg|plug-in circuit]] uses the shift instructions in time slot 1 to implement the change of range.
==Analog-ROM Readout Board==
 
===Character generation===
[[File:7000-readout-chargen-positions.jpg|thumb|300px|right|Character generator matrix positions in 7000 series readout analog character generator ROM]]
The character generators are custom analog chips that provide X and Y output currents for ten characters of up to seven strokes (eight X/Y coordinate pairs) inscribing each character.  The in-character coordinate points are selected through a triangular analog signal, not a digital code, which in turn activates one of eight groups of three transistors each generating the X/Y output currents.  Each of these groups is fed a constant emitter current (I<sub>E</sub>), and the distribution of this current to the three transistors is controlled by their different emitter areas.  The first and second collectors provide X and Y currents respectively, the third ("Z") directs current to the substrate (I<sub>E</sub> - I<sub>X</sub> - I<sub>Y</sub> - I<sub>Z</sub> = 0).  Actually, the emitter area itself is not varied in the mask, but out of a fixed number of emitters of equal size, a certain number is connected on each transistor:  [[File:7000-readout-chargen-circuit-1.jpg|300px|thumb|ROM circuit for one character (digit "3"). Bases are scanned in turn. The numbers under the emitters indicate how many of the emitters are connected to the common rail. Ten such character circuits plus the scanning (base drive) circuit are integrated in each ROM chip.  All X and Y collector outputs are connected across characters and chips.]]
If the bases were controlled by a digital decoder, only one triplet of transistors would be active at any time and only points would be generated on the display.  Instead, through an analog driving circuit, gradual cut-over is achieved, i.e. current from one group is reduced while that from the next group is increased, and a linear transition from the first to the second X/Y coordinate pair is displayed as a stroke on the CRT. The actual shape of the base drive voltages has great influence on the proper character rendering (this is explained at length in Gilbert's 1971 SSC paper).
 
[[File:Tek-7000-readout-board.jpg|400px|center|Analog-ROM readout board (from [[7904]] built in 1981)]]


==Custom chips==
===Custom chips===
* [[155-0014-01]] Analog to Decimal Converter
* [[155-0014-01]] Analog to Decimal Converter
* [[155-0015-01]] Analog Data Switch
* [[155-0015-01]] Analog Data Switch
Line 56: Line 69:
* [[155-0038-01]] D/A converter
* [[155-0038-01]] D/A converter


===Analog-ROM Readout Board===
==EPROM-based Readout Board==
 
[[File:EPROM based 7000 series readout board.jpg|400px|right]]
[[File:Tek-7000-readout-board.jpg|600px|Typical readout board (from [[7904]] built in 1981)]]
 
===EPROM-based Readout Board===
[[File:Readout-1.jpg|thumb|right|Analog ROM board]]
[[File:Readout-2.jpg|thumb|right|EPROM board]]
Towards the end of the 7000 series lifespan, in the 2nd half of the 1980s, a re-designed readout board,  
Towards the end of the 7000 series lifespan, in the 2nd half of the 1980s, a re-designed readout board,  
Tek part number 670-8622, was introduced, in which the character generator is based on digital values stored in a 2732 EPROM instead of Gilbert's analog ROMs.  This board was installed e.g. in the [[R7103]] and [[7904A]] and still used some of the Tek-made readout ICs like the timing generator.
Tek part number 670-8622, was introduced, in which the character generator is based on digital values stored in a 2732 EPROM instead of Gilbert's analog ROMs.  This board was installed e.g. in the [[R7103]] and [[7904A]] and still used some of the Tek-made readout ICs like the timing generator.
The number of display points was increased to up to 16 per character. The presence of this board can be detected from the outside by looking at the readout characters which are straight up but were italicized in the analog version (which was done the analog way too, by adding some 10% of the vertical signal to the horizontal channel).  The character style itself is also different — for example, the "V" in the classic board has just two straight lines, whereas they are angled in the digital version.
The number of display points was increased to up to 16 per character. The presence of this board can be detected from the outside by looking at the readout characters which are straight up but were italicized in the analog version (which was done the analog way too, by adding some 10% of the vertical signal to the horizontal channel).  The character style itself is also different — for example, the "V" in the classic board has just two straight lines, whereas they are angled in the digital version.
[[File:EPROM based 7000 series readout board.jpg|400px]]


===Microcontroller-based Readout Board===
:{|
|-
| [[File:Readout-1.jpg]] || [[File:Readout-2.jpg]]
|-
| Analog ROM board      || EPROM board
|-
|}
 
==Microcontroller-based Readout Board==
Finally, from 1989/1990 on, a third generation readout board designed around an 80C31 micro-controller replaced the previous versions in the last series of [[7104]], [[R7103]], [[R7844]] and [[7904A]] models.This version no longer used any Tek-made special ICs, manufacture of which had been discontinued by that time. The 8031 based board is described in [http://w140.com/Tek_7904_OCRed_by_Tabalabs.pdf this version of the 7904A manual].
Finally, from 1989/1990 on, a third generation readout board designed around an 80C31 micro-controller replaced the previous versions in the last series of [[7104]], [[R7103]], [[R7844]] and [[7904A]] models.This version no longer used any Tek-made special ICs, manufacture of which had been discontinued by that time. The 8031 based board is described in [http://w140.com/Tek_7904_OCRed_by_Tabalabs.pdf this version of the 7904A manual].
[[File:Microcontroller based readout board block diagram.jpg|600px|Block diagram of 8031 based readout board]]
[[File:Microcontroller based readout board block diagram.jpg|600px|Block diagram of 8031 based readout board]]
Retrieved from "https://w140.com/tekwiki/wiki/Special:MobileDiff/15190"