175: Difference between revisions

From TekWiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 32: Line 32:
==Pictures==
==Pictures==
<gallery>
<gallery>
File:Tek 175 front.jpg|Front
Tek 175 front.jpg|Front
File:Tek 175 front2.jpg|Front
Tek 175 front2.jpg|Front
File:Tek 175 left.jpg|Left
Tek 175 left.jpg|Left
File:Tek 175 left open.jpg|Left internals
Tek 175 left open.jpg|Left internals
File:Tek 175 right.jpg|Right
Tek 175 right.jpg|Right
File:Tek 175 right open.jpg|Right internals
Tek 175 right open.jpg|Right internals
File:Tek 175 back.jpg|Rear
Tek 175 back.jpg|Rear
File:Tek 175 step amp.png|Step amp
Tek 175 step amp.png|Step amp
File:Tek 175 switching diagram.png|Switching diagram
Tek 175 switching diagram.png|Switching diagram
File:Tek 175 collector sweep.png|Collector sweep
Tek 175 collector sweep.png|Collector sweep
File:Tek 175 bottom.jpg|Bottom view
Tek 175 bottom.jpg|Bottom view
File:Tek 175 bus bar.jpg|Left internal
Tek 175 bus bar.jpg|Left internal
File:Tek 575 on 175.jpg
Tek 575 on 175.jpg
Tek 148-015 1.jpg|147-015 20 ampere relay used in 175
Tek 148-015 2.jpg|147-015 20 ampere relay used in 175
Tek 148-015 3.jpg|147-015 20 ampere relay used in 175
</gallery>
</gallery>


[[Category:Curve tracers]]
[[Category:Curve tracers]]
[[Category:Introduced in 1961]]
[[Category:Introduced in 1961]]

Revision as of 23:00, 23 November 2017

The Tektronix 175, introduced in 1961, is an external unit that extends the current capability of the 575 curve tracer. The 175 uses the standard circuit topology for the collector supply: a variac followed by a multi-tap isolation transformer, followed by full-wave rectifiers.

There are two modes:

  • 0 - 20 V collector voltage, 200 A maximum collector current
  • 0 - 100 V collector voltage, 40 A maximum collector current

Separate transformer taps and rectifiers are used for the two modes. In the 0-20 V mode, 45L10 rectifiers are used. Unlike the 575, which routes the test current through the front panel switches, the 175 routes the 0-20 V collector supply through 100 A relays, whose coil current are switched by the front panel (i.e., the "COLLECTOR POLARITY" and "TRANSISTOR SELECTOR") controls. Otherwise, the front panel switches would have to handle high currents and would be massive and difficult to operate. The front panel switches are break-before-make, which is important because if the relay coils were to be energized in the wrong combination, a short circuit would be formed. In the 0-100 V mode, the test current flows through the front panel switch.

The Tektronix 175 requires a 575 to work, which provides +300 V, +100 V, and -150 V to power the step generator circuit in the 175. The cable that connects the 175 to the 575 uses Amphenol 165-14 and 165-15 connectors.

The front panel of the 175 has Superior Electric Supercon connectors for the high-current measurements. The positive (red) plug that goes into the 175 is a model PP100GR pin plug. The negative (black) plug that goes into the 175 is a model PS100GB socket plug.

The 175 is 12"x13"x24" and weighs 38 kg (84 pounds). Most of the weight of the 175 is due to the large transformer for the collector supply.

Pictures