422: Difference between revisions

Revision as of 10:50, 6 May 2021

{{{manufacturer}}}

15 MHz portable dual-trace scope

Produced from 1965 to 1975

Manuals

(All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix Type 422 is a 15 MHz portable dual-trace oscilloscope introduced in 1966. It was available with an optional battery back for operation without mains power.

Key Specifications

Bandwidth	DC to 15 MHz
Rise time	< 23 ns
Sweep	500 ns/div to 0.5 s/div
Input Impedance	1 MΩ ±2% // 30 pF
Delay Line	150 ns, internal delay line
Input Voltage	Max. 300 V combined DC and peak AC
Trigger Source	CH1 & CH2, CH1, External
Channel Isolation	100:1 at 40 KHz
Calibrator	~1 kHz ±20%, 2 V ext jack, 0.2 V internal, square wave
CRT	T4220 tube, P31 phosphor, 6 kV acceleration (Post-def 4.9 kV), 8 × 10 graticule, 0.8 cm/div
Operating temprature	-15 °C to +55 °C
Line Voltage/Power AC PS	110/115/125 OR 210/230/250 V_AC ±10%, 45 Hz to 440 Hz, 40W
Line Voltage/Power AC-DC PS	92-137 OR 184-274 V_AC, 45 Hz to 440 Hz, 11.5-35 V DC, 30W
Dimensions	AC PS (H/W/D) 6.75/10.0/17.8 inches, AC-DC PS (H/W/D) 6.75/10.0/20.7 inches

Internals

Early versions use an 8056 Nuvistor tube for the front-end cathode follower. Later versions use a FET front end. The 8056 Nuvistor used in the input amplifier of the 422 can be replaced by a MPF102 JFET.

The trigger circuit in the 422 has a trigger amplifier driving a 1N3719 tunnel diode, D375, which acts as a Schmitt trigger. The trigger amplifier has a nonlinear deadband diode circuit in the negative feedback path. What results is high gain for small signals (little or no negative feedback) and low gain for large signals (strong negative feedback). Thus, the signal at the base of Q364 has a limited swing over a wide range of input amplitudes. The collector current of Q364 varies between 0 and 9 mA. Depending on the position of the trigger slope control, higher collector current in Q364 either switches D375 from the low-voltage state to the high-voltage state or from the high-voltage state to the low-voltage state. When D375 transitions from the low-voltage state to the high-voltage state, it produces a current pulse in the primary of transformer T401, which produces a current pulse in the secondary of T401. The secondary of T401 feeds another tunnel diode, D405, and the current pulse switches D405 to the high-voltage state, which starts a sweep.

The 422 uses the T4220 CRT.

Links

LazyElectrons Video on 422

Pictures

External

R422, compartment closed
R422, compartment open
Black 422, panel mount
422 trace is sharp
422 in ALT

Internal

Tek 422 Internal LHS
Tek 422 Internal RHS
Tek 422 Internal Top
Tek 422 Internal Rear
Tek 422 Internal Underside
Tek 422 Internal V-Amp
Tek 422 H-Amp Board
Tek 422 Trigger Board
Tek 422 Input Board#1
Tek 422 Input Board#1
Tek 422 Indicator unit - Regulator
Tek 422 HV Case
MPF102 replacing 8056
Tek422 AC Power Supply Module
Tek 422 AC Power supply Internal
Tek 422 AC Power supply Internal
Tek 422 AC Power supply Internal
Tek 422 AC Power supply Internal
Tek 422 AC Power supply Internal
Tek 422 Indicator unit, Power supply Test points

Schematic

Trigger circuit
Sweep circuit
Vertical amplifier circuit
Input amplifier circuit
Horizontal amplifier circuit
CRT circuit
ac-dc power supply
ac power supply

@@ Line 21: / Line 21: @@
 * [[Media:Tek 422 fcp april 1969.pdf]]
 * [[Media:070-0549-00.pdf|Installation Instructions for Tek 422 Battery Pack (PDF, needs OCR)]]
+* [[Media:Tek 422 cal notes.pdf]]
 }}
 The '''Tektronix Type 422''' is a 15 MHz portable dual-trace oscilloscope introduced in 1966.