Nicolet 526: Difference between revisions
No edit summary |
(remove parent category) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{Instrument Sidebar | |||
|manufacturer=Nicolet | |||
|model=526 | |||
|class=Digital | |||
|series=5000-series scopes | |||
|summary=Signal averager | |||
|image=Nicolet_526_1.jpg | |||
|caption=Nicolet 526 | |||
|introduced=1976 | |||
|discontinued=(?) | |||
|designers= | |||
|manuals= | |||
*''please add'' [[Category:Manual needed]] | |||
}} | |||
The '''Nicolet 526''' is a signal averager that is used in a modified OEMed [[5110|Tektronix 5110]] ([[5103N]]/[[D10]]) mainframe. | The '''Nicolet 526''' is a signal averager that is used in a modified OEMed [[5110|Tektronix 5110]] ([[5103N]]/[[D10]]) mainframe. | ||
The modifications to the mainframe performed by Nicolet include | The modifications to the mainframe performed by Nicolet include | ||
| Line 6: | Line 20: | ||
The 526 has its own +5V regulated rail. | The 526 has its own +5V regulated rail. | ||
An external source of +7V unregulated DC is routed from thee 12-pin rear connector to the mainframe interface board, | <!--An external source of +7V unregulated DC is routed from thee 12-pin rear connector to the mainframe interface board, | ||
and into the plug-in. | and into the plug-in.--> | ||
An LM323 +5V three-terminal regulator is the source of the +5V rail within the Nicolet 526. | An LM323 +5V three-terminal regulator is the source of the +5V rail within the Nicolet 526. | ||
(Even though the input is marked "+7 UNREG" on the board, it should probably be +7.5V minimum, | (Even though the input is marked "+7 UNREG" on the board, it should probably be +7.5V minimum, | ||
| Line 19: | Line 33: | ||
Mechanically, the Nicolet 526 is a three-bay 5000-series plug-in. | Mechanically, the Nicolet 526 is a three-bay 5000-series plug-in. | ||
It mates with the center-bay plug-in connector. | It mates with the center-bay plug-in connector. | ||
The Nicolet 526 is made of four boards and a backplane. | The Nicolet 526 is made of four boards and a backplane which has a 40 position two sided edge connector for each board. | ||
Connection to the Tektronix mainframe is done via | Connection to the Tektronix mainframe is done via the backplane. | ||
The four boards are: | The four boards are: | ||
* ADC and Register: The SIGNAL wire from pin 23A on the plug-in interface goes to the inverting input of an LM301 opamp via a resistance of around 165 kΩ. The noninverting input of this opamp is grounded. | * ADC and Register: The SIGNAL wire from pin 23A on the plug-in interface goes to the inverting input of an LM301 opamp via a resistance of around 165 kΩ. The noninverting input of this opamp is grounded. | ||
| Line 36: | Line 50: | ||
* RO TRIG (violet) 26B | * RO TRIG (violet) 26B | ||
* Y LOCK IN (blue) 25B | * Y LOCK IN (blue) 25B | ||
* FID SIG (green) maybe "FID" stands for "Free Induction Decay" in NMR? 24B | * FID SIG (green) maybe "FID" stands for "Free Induction Decay" in NMR? pin 24B on the interface connector, wired to pin 33 of the board #2 (address). | ||
* SIGNAL (brown) 23A | * SIGNAL (brown) 23A | ||
* RO STUS (yellow) 23B | * RO STUS (yellow) 23B | ||
| Line 76: | Line 90: | ||
| 9 || | || | | 9 || | || | ||
|- | |- | ||
| 10 || | | | 10 || | +7 UNREG || | ||
|- | |- | ||
| 11 || | || | | 11 || | || | ||
| Line 108: | Line 122: | ||
[[Category:5000 series plugins]] | [[Category:5000 series plugins]] | ||
[[Category:Specifications needed]] | [[Category:Specifications needed]] | ||
[[Category:Nicolet products]] | [[Category:Nicolet products]] | ||
Latest revision as of 00:45, 12 March 2022
The Nicolet 526 is a signal averager that is used in a modified OEMed Tektronix 5110 (5103N/D10) mainframe. The modifications to the mainframe performed by Nicolet include
- adding a perforated panel for fan cooling via the bottom panel of the scope,
- adding a 12-pin connector on the rear panel of the scope
- connected the 12-pin connector to the interface board, connector J604.
The 526 has its own +5V regulated rail. An LM323 +5V three-terminal regulator is the source of the +5V rail within the Nicolet 526. (Even though the input is marked "+7 UNREG" on the board, it should probably be +7.5V minimum, per the LM323 datasheet.) Since the LM323 is rated for 3 amperes, it is unlikely that the plug-in sinks more than that from the "+7 UNREG" input.
How does the Nicolet 526 get the horizontal signal to the scope if it only plugs into the right vertical plug-in interface connector? In a standard, unmodified 5103, there is no signal path from the right vertical connector to the horizontal amplifier.
Mechanically, the Nicolet 526 is a three-bay 5000-series plug-in. It mates with the center-bay plug-in connector. The Nicolet 526 is made of four boards and a backplane which has a 40 position two sided edge connector for each board. Connection to the Tektronix mainframe is done via the backplane. The four boards are:
- ADC and Register: The SIGNAL wire from pin 23A on the plug-in interface goes to the inverting input of an LM301 opamp via a resistance of around 165 kΩ. The noninverting input of this opamp is grounded.
- Address
- Control
- Memory
The design makes heavy use of 7400-series digital logic in DIP packages. The printed circuit boards are two-layer. The memory is an array of Fairchild 2102DC MOS 1k x 1 static RAM ICs, DIP, soldered in place.
The wires connecting the backplane board on the 526 to the mainframe interface connector on the 526 are labeled:
- H LOCK TRIG (white w/ black stripe), pin 27B of the plug-in connector
- TRIGGER (light violet) 26A
- RO TRIG (violet) 26B
- Y LOCK IN (blue) 25B
- FID SIG (green) maybe "FID" stands for "Free Induction Decay" in NMR? pin 24B on the interface connector, wired to pin 33 of the board #2 (address).
- SIGNAL (brown) 23A
- RO STUS (yellow) 23B
- +7 UNREG (black), pin 22A and 22B of the plug-in connector
- +7 UNREG (black), pin 22A and 22B of the plug-in connector
- GND (white) 14A and 14B (standard 5000-series pinout)
- GND (white) 14A and 14B (standard 5000-series pinout)
- -VERT SIG (white w/ red stripe) 13B (standard 5000-series pinout for vert CH2)
- +VERT SIG (white w/ brown stripe) 13A (standard 5000-series pinout for vert CH2)
- -HORIZ SIG (white w/ orange stripe) 11B
- +30 (red) 5A (standard 5000-series pinout)
- -30 (orange) 5B (standard 5000-series pinout)
- 11A is jumpered to 14B at the male plug-in connector of the 526.
The 12-pin rear-panel connector has its pins numbered on the inside of the connector.
| Pin | Function | Comment |
|---|---|---|
| 1 | ||
| 2 | ||
| 3 | ||
| 4 | ||
| 5 | ||
| 6 | ||
| 7 | ||
| 8 | ||
| 9 | ||
| 10 | +7 UNREG | |
| 11 | ||
| 12 |
-
Front
-
Top
-
Left
-
Right
-
Bottom
-
ADC and Register
-
ADC and Register
-
Address Board
-
Address Board
-
Control Board
-
Control Board
-
Memory
-
Memory
-
Rear
-
Top front
-
Right front
-
Bottom front
-
Mainframe rear connector internal
-
Mainframe rear connector external
-
Mainframe rear connector to J604
