TDS784: Difference between revisions

Revision as of 21:54, 21 June 2022

Tektronix TDS784

1 GHz, 4 GS/s 4-channel digital scope

Produced from 1995 to (?)

Manuals

Common

TDS784A

TDS784C

TDS784D

(All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix TDS784 is a 1 GHz, 4 GS/s four-channel digital storage scope with a color screen.
There are four variants, all with the same specs but different hardware/software loads − TDS784A, B, C & D. Of these, the C and D models are the least problematic and most sought-after.

Key Specifications

Bandwidth	1 GHz at 10 mv/div and above; 750 MHz @ 5 mV/div; 600 MHz @ 2 mV/div; 500 MHz @ 1 mV/div
Sample rate	1 channel @ 4 GS/s, 2 channels @ 2 GS/s, 3 or 4 channels @ 1 GS/s
Number of Channels	4
Vertical Sensitivity	1 mV to 10 V/div with calibrated fine adjustment
Resolution	8 bit
Time Base Range	200 ps to 10 s/div
Record length	50k samples per channel
Record Length (1M Option)	500 K points on 1 channel; 250 k points on 2 channels ; 130 k points on 3 or 4 channels
Record Length (2M Option)	8 M points on 1 channel; 4 M points on 2 channels ; 2 M points on 3 or 4 channels
Acquisition modes	sample, envelope, average, high-resolution, peak-detect
Display	Color; Zoom
Trigger modes	Edge, logic, pulse; Video trigger with option 05 (NTSC, SECAM, PAL, HDTV, and FlexFormat)
Storage	1.44 Mbyte, 3.5 inch, DOS 3.3-or-later floppy disk. NVRAM storage for saving waveforms, hardcopies, and setups. Units with option HD present (requires additional hardware) have a hard disk drive
I/O	Full GPIB programmability
Hardcopy	Using GPIB, RS-232, or Centronics ports

Software

Tektronix TDS300, 400, 500, 600, 700, 800 AWE Drivers 066-0087-00 (ZIP)
Telecom Test and I-Pattern Software TTiP 066-0119-00 (ZIP)
Enhanced Printing Utility for TDS Family 066-0125-00 (ZIP)
TDS runtime Environment TDSRTE1 066-0127-00 (ZIP)
Tektronix TDS500C/700C Custom Masks 066-0165-00 (ZIP)
Tektronix Wavestar 2012.05.09.11.07.29 16456 EN 066-0934-03 (ZIP, 102MB) Product Key: WSTRO618650124

Firmware

Options

05 - Video Trigger - Oscilloscope comes with tools that allow investigation of a range of NTSC, PAL, SECAM, and high definition TV signals.
13 - RS-232C and Centronics hardcopy interfaces - Add RS-232-C and Centronics interface ports.
1F - Floppy disk drive - Add 3.5 inch, 1.44 MByte floppy disc drive.
1G - 1 GS/s maximum - Limit sample rate from 5 GS/sec to 1 GS/sec when acquiring 1 to 4 channels (Export restriction compliance). (TDS 754D Only)
1M - 4M acquisition length - Extends standard acquisition length from 50,000 points per channel to 130,000 samples on three or four channels, 250,000 samples on two channels, and 500,000 samples on one channel.
2C - Communication Signal Analyzer - Oscilloscope comes configured for communications signal triggering and mask testing.
2F - Advanced DSP math - Add advanced DSP math features such as FFT, integration, and differentiation.
2M - 8M acquisition length - TDS 520D, 724D: To 2M samples on two channels and 4M on one channel. TDS 540D, 580D, 714L, 754D, 784D, 794D: To 2M samples on three or four channels, 4M on two channels, and 8M samples on one channel (Option includes a hard disk and is only available for the models listed above.)
3C - P6701B with system calibration - Oscilloscope comes with a P6701B and calibrated short-wavelength optical reference receiver on channel 1.
4C - P6703B with system calibration - Oscilloscope comes with a P6703B and calibrated long-wavelength optical reference receiver on channel 1.
HD - Hard Disk - 170Mb internal hard disk drive.

Optional Accessories

1K - Add K420 scope cart
1R - Rackmount kit
24 - Add 4 each P6139A passive probes
26 - Add 4 each P6245 active probes
3I/3P - Colour printer and cable (220V/110V)
B2 - Hardcopy version of the programmers manual
L1 - Substitute French user manual
L3 - Substitute German user manual
L5 - Substitute Japanese user manual
L9 - Substitute Korean user manual

Included Accessories

020-2204-00 - Quick Reference in 8 languages
070-6869-00 - User Manual
070-9874-01 - Technical Reference
063-2773-00 - Programmer's Manual in MS-Help format on floppy disk
NIST, MIL-STD-45662A and ISO9000 calibration certificate
200-3696-01 - Front cover
161-0230-01 - US power cord
016-1268-00 - Accessory pouch

Recommended Accessories

070-9875-00 - Service Manual
012-0991-01 - 1m GPIB cable
012-0991-00 - 2m GPIB cable
012-1298-00 - RS-232 cable
012-1250-00 - Centronics cable
016-0909-01 - Soft-sided carrying case
016-01135-00 - Transit case
K420 - Scope cart

Software Options

LVWIN - LabVIEW for PC Windows OS
LWCVI - LabWindows for CVI system
LWDOS - LabWindows for DOS OS
S3FT400 - WaveWriter AWG and waveform creation software
TTiP - Telecommunications Templates and i-Pattern software
WSTR31 - WaveStar waveform capture and documentation software

Links

See the Repairs page regarding HDD/FDD replacements.

Internals

For units with serial numbers prior to B04xxxx, the latest known firmware revision is 6.6e. For units with serial numbers B04xxxx and above, the last known version is 7.4e. Note that, due to differences in acquisition and CPU board hardware, release 7.4e will not work in the earlier revision units. Early revision units may have a CPU board P/N of 679-4172-00. The later revision is 679-4349-00.

It is also worth noting the TDS754 and TDS784 series are nearly identical, with the differences being in front-panel cosmetics and the presence (754) or absence (784) of a few capacitors on the acquisition board. The only other difference is the position of instrument ID jumpers, also on the acquisition board. In fact, it is entirely possible to convert a 754 to a 784 (see the 'Links' section).

Note that any kind of firmware updating of the 784 (and most other similar TDS scopes) requires very specific equipment, starting with an older computer (ISA slots required) running MS-DOS 5.x or later as well as Windows 98SE. To interface with the scope, you will need a National Instruments PC/GPIB-II ISA-based (8-bit) GPIB board or a National Instruments AT-GPIB (16-bit) board and appropriate drivers. The software required to do the update (Tektool or Tekfwtool) also runs under DOS (or a DOS box in Windows 98). Information on this tool can be found in the Links section in the thread describing firmware updates.

Actual calibration requires the above computer, the specific PC/GPIB-II card and drivers and an MS-DOS environment. You will also need an Analogic/Data Precision model 8200 DC voltage standard and a levelled sine-wave generator capable of going up to 1 GHz (if you're just doing a 754, you can get away with a 500 MHz top end). Naturally, Tek used the SG503 and SG504.

The reason for the specific model of voltage standard is because that's the model Tektronix wrote the calibration software for. During the calibration process, it issues automated commands specific to the Analogic.

Note that in the TDS700D series, the acquisition board variant is important — the CPU Board with Firmware 7.xx cannot be used together with the old acquisition board, and the CPU board with old Firmware 6.xx doesn't run with the new acquisition board. The fact that the CPU board has part number 671-4349-00 is by itself not a reliable indication of a compatible firmware version.

Finally, for those with a dimming CRT, Simmconn Labs has developed a color LCD panel kit to replace said CRT in most of the TDS series which use them.

Pictures

Front View
Rear View without Opt. 13
Option 05 Internal Parts
Option HD Internal Parts, 2.5" Disk Version
Option HD Internal Parts, PCMCIA Disk Version

@@ Line 40: / Line 40: @@
 * [[Media:070-9384-01.pdf|TDS500B/600B/700A Performance Verification and Specifications 070-9384-01]]
 * [[Media:070-9386-03.pdf|TDS500B/600B/700A Service 070-9386-03]]
-* [[Media:070-9473-01.pdf|TDS684A/744A/784A Firmware Field Upgrade 070-9473-01]]
+* [[Media:070-9473-01.pdf|TDS684A/744A/784A Firmware Field Upgrade TDS 7U01 070-9473-01]]
 * [[Media:070-9719-00.pdf|TDS500B/600B/700A Digitizing Oscilloscopes 070-9719-00]]
 * [[Media:070-9721-02.pdf|TDS500B/600B/700A Service Manual 070-9721-02]]