M377
The M377 is a Tek-made amplifier integrated circuit designed by John Addis. It is used in the 11A16, 11A32, 11A33, 11A34, and 11A52.
About the M377, John Addis says:
The M377 was a single channel plugin on a chip with 0 V common mode input and output voltages, excellent variable gain control, two four pole bandwidth limits, three outputs which could be separately inverted and turned on or off.
It was the first wideband analog IC with level shift on chip (allowing 0 V common mode input and output and without PNP transistors), first wideband amplifier with any on-chip bandwidth limit selection, first to have more than two fixed gain settings (it has six), and first to require only one transient response adjustment (no thermals), and the first to have a highly linear relationship between a control voltage and gain. It also had excellent overdrive recovery.
The packaged M377 die has the following Tek part numbers:
- 165-2129-03
- 165-2089-06
- 155-2089-05 (11A33)
| Instrument | Instrument SN range | Part Number | Output R/side | Components on ceramic hybrid |
|---|---|---|---|---|
| 11A32 | B010100 - B031028 | 165-2089-03 | 100 ohms | M377 chip only |
| 11A32 | B031029 - up | 165-2089-05 | 100 ohms | M377 chip only |
| 11A34 | B010100 - B031044 | 165-2089-04 | 200 ohms | M377 chip only |
| 11A34 | B031045 - up | 165-2089-06 | 200 ohms | M377 chip only |
| 11A52 | B010100 - B010179 | 165-2129-02 | 100 ohms | Diode bridge + 50 ohm input R + M377 chip |
| 11A52 | B010180 - up | 165-2129-03 | 100 ohms | Diode bridge + 50 ohm input R + M377 chip |
165-2089-xx Pinout
| Pin | Function |
|---|---|
| 1 | GP0 (gain select bit 0) |
| 2 | GS |
| 3 | +15V |
| 4 | +Vin |
| 5 | Analog ground |
| 6 | -Vin |
| 7 | Analog ground |
| 8 | Var Gain |
| 9 | -5V |
| 10 | -5V |
| 11 | Display Invert |
| 12 | Display On |
| 13 | Analog Ground |
| 14 | +5V |
| 15 | Trigger Invert |
| 16 | Trigger On |
| 17 | +5V |
| 18 | Aux Trigger On |
| 19 | -Display |
| 20 | +Display |
| 21 | HF Adjust terminal 1 |
| 22 | -Trigger |
| 23 | +Trigger |
| 24 | HF Adjust terminal 1 |
| 25 | -Aux Signal |
| 26 | +Aux Signal |
| 27 | HF Adjust terminal 2 |
| 28 | Ground |
| 29 | Ground |
| 30 | Ground |
| 31 | +5V |
| 32 | -5V |
| 33 | BP1 (bandpass select bit 1) |
| 34 | BP0 (bandpass select bit 0) |
| 35 | GP2 (gain select bit 2) |
| 36 | GP1 (gain select bit 1) |
Pin function legend
Power pins Ground pins HF signals TTL digital control signals analog control signals
-
M377 in an 11A52, as U310 and U410. Each M377 chip has a differential output impedance of 200 Ω. The two chips' outputs are in parallel, driving the output pins of the plug-in with a differential impedance of 100 Ω, or 50 Ω per side.
-
Two M377 chips (packaged as part number 165-2129-03) in an 11A52.
-
M377 die
-
