1M1: Difference between revisions

1M1 (view source)

Revision as of 09:57, 13 August 2021

62 bytes removed , 13 August 2021

no edit summary

Peter

Bureaucrats, Interface administrators, Suppressors, Administrators

36,507

edits

@@ Line 1: / Line 1: @@
-{{Plugin Sidebar 2|
+{{Plugin Sidebar |
-manufacturer=Tektronix | model=1M1 |
+|manufacturer=Tektronix
-summary=Calibration plug-in |
+|series=500-series scopes
-image=Tek 1m1 front.jpg |
+|model=1M1
-caption=Tek 1M1 |
+|summary=Calibration plug-in
-series=[[500-series scopes]] |
+|image=Tek 1m1 front.jpg
-introduced=1964 |
+|caption=Tek 1M1
-discontinued=(?) |
+|introduced=1964
-manuals=
+|discontinued=(?)
+|designers=
+|manuals=
 * [[Media:070-0407-01.pdf|Tektronix 067-0521-00 Manual (PDF)]]
 * [[Media:070-0407-02.pdf|Tektronix 067-0521-01 Manual (PDF)]]
@@ Line 17: / Line 19: @@
 * [[Media:Tek tu-7 irb.pdf|Tektronix TU-7 Instrument Reference Book (PDF, OCR)]]
 * [[Media:Tek 067-0521-00 fcp july 1969.pdf|Tektronix 067-0521-00 Factory Calibration Procedure, July 1969‎]]
-[[Category:500 series plugins]]
-[[Category:Calibration fixtures]]
 }}
-The '''Tektronix [[TU-7]]/1M1/[[067-0521-00]]''' is a [[Letter-series_and_1-series_plug-ins|letter series plug-in]]
+The '''Tektronix [[TU-7]]/1M1/[[067-0521-00]]''' is a [[Letter-series_and_1-series_plug-ins|letter series plug-in]] used for calibrating [[500-series scopes]].
-used for calibrating [[500-series scopes]].
-It is a multifunction replacement for the [[P|Type P Pulser]], the [[TU-2|TU-2 Test Load]],
+It is a multifunction replacement for the [[P|Type P Pulser]], the [[TU-2|TU-2 Test Load]], and the [[EP-53|EP-53 Gain Set Adaptor]].
-and the [[EP-53|EP-53 Gain Set Adaptor]].
-It is used for calibrating the mainframe's step response and gain,
+It is used for calibrating the mainframe's step response and gain, checking dual-trace operation, common mode rejection, and power supply regulation.
-checking dual-trace operation, common mode rejection, and power supply regulation.
-(500-series mainframes are designed to have
+(500-series mainframes are designed to have 10 div/Volt response to differential signals from the plug-in, and zero response to common-mode signals.)
-div/Volt response to differential signals from the plug-in,
-and zero response to common-mode signals.)
-It contains a transistor multivibrator whose output is sharpened
+It contains a transistor multivibrator whose output is sharpened through Tek-made Gallium-Arsenide diodes (later production used silicon), a dual-trace circuit using [[12AT7]] and [[6AL5]] tubes, and various load resistors.
-through Tek-made Gallium-Arsenide diodes (later production used silicon),
-a dual-trace circuit using [[12AT7]] and [[6AL5]] tubes, and various load resistors.
 It does not have the Type P's short operating life because it does not use a [[mercury switch]].
-This instrument went through several names.
+This instrument went through several names. At its [[introduced in 1964|1964]] introduction, it was the '''TU-7'''.
-At its [[introduced in 1964|1964]] introduction, it was the '''TU-7'''.
+Some early Tek-internal instruments for design, manufacturing, and calibration had TU (Test Unit) nomenclature.
-Some early Tek-internal instruments for design,
+(Other examples include the [[TU-75B]] Variac, the TU-?? dim-bulb fixture, and the [[TU-50]] sine/square/pulse generator.)
-manufacturing, and calibration had TU (Test Unit) nomenclature.
-(Other examples include the [[TU-75B]] Variac, the TU-?? dim-bulb fixture,
-and the [[TU-50]] sine/square/pulse generator.)
 In 1965, it was renamed '''Type 1M1''' to fit into the letter-series nomenclature like its predecessor.