TekWiki

511: Difference between revisions

Page Discussion Repairs

511 (view source)

Revision as of 09:23, 15 November 2023

2,741 bytes added ,  15 November 2023
no edit summary
No edit summary
No edit summary
 
(46 intermediate revisions by 4 users not shown)
Line 1: Line 1:
{{Oscilloscope Sidebar |
{{Oscilloscope Sidebar TEST
title=Tektronix 511|
|manufacturer=Tektronix
summary=10 MHz Tube scope<br />''First Tektronix product''|
|series=
image=Tek 511 1.jpg|
|model=511
caption=Tektronix 511 front |
|summary=10 MHz Tube scope<br />''First Tektronix oscilloscope''
introduced=1947 |
|image=Tek 511 1.jpg
discontinued=1953 |
|caption=Tektronix 511 front
manuals=
|introduced=1947
* [http://w140.com/tek_511.pdf Tektronix 511 Manual (PDF)]
|discontinued=1953
* [http://bama.edebris.com/download/tek/511aearly/Tek%20511A%20Pre%20SN2869.pdf Tektronix 511A Manual pre SN 2869 (PDF)]
|designers=Frank Hood;Logan Belleville;Howard Vollum
* [http://bama.edebris.com/download/tek/511alater/Tek%20511A%20SN%202869-5099.pdf Tektronix 511A Manual SN 2869-5099 (PDF)]
|manuals=
* [http://richardsears.wordpress.com/2012/01/07/near-the-beginning-of-an-era-the-tektronix-511a/ Richard Sears' 511A Page]
* [[Media:IM-511.pdf|Tektronix 511/511A Manual]] (OCR, includes S/N 5100+ information)
* [http://w140.com/1947+Tektronix_Catalog.pdf Tektronix 1947 Catalog with 511 (PDF)]
* [[Media:IM-511A-1.pdf|Tektronix 511A Manual SN <2869]] (OCR)  
* [[Media:IM-511A-2.pdf|Tektronix 511A Manual revised in 1951 for SN 2869-5099]] (OCR)
* [[Media:1947_Tektronix_Catalog.pdf|Tektronix 1947 "Catalog" (511 only)]]
}}
The 511 was Tektronix' '''first oscilloscope''', [[introduced in 1947|introduced in June 1947]] but only the second product released by the young company – the first was the [[101|Type 101 Video Calibrator]].
[[Howard Vollum]] was directly involved with the design of the 511.
__TOC__
According to TekWeek March 23, 1984, ''"511" stood for 5-inch tube, 1 channel, 1st model.  It sold for $795<sup>[Note 1]</sup>, compared to $1,800 for a two-piece Dumont scope that was mostly pre-war technology.''


}}
An improved version, the 511A, was [[introduced in 1948|introduced in November 1948]].  Major improvements included a regulated power supply for CRT, and a (in later models, s.b.) a calibrator.  The 511AD was available through 1953.
The 511 was '''Tek's first product''',
 
[[introduced in 1947|introduced in June 1947]].   
{{BeginSpecs}}
A revised version, the 511A, was [[introduced in 1950]].  
{{Spec | Bandwidth  | 5 Hz to 10 MHz (8 MHz with 2-stage amplifier); no DC coupling }}
[[Howard Vollum]] was directly involved with the design of the 511.
{{Spec | Rise time  | 40 ns (50 ns with 2-stage amplifier) }}
{{Spec | Deflection | Without amplifier, 27 V/cm – 200 V/cm, DC or AC<sub>p-p</sub>.  1-stage amplifier, 2.7 V/cm – 40 V/cm.  2-stage amplifier, 0.27 V/cm – 4 V/cm. }}
{{Spec | Input      | 1 MΩ // 40 pF; 600 V max. DC+peak AC }}
{{Spec | Sweep      | 100 ns/cm to 10 ms/cm + variable; ×5 magnifier }}
{{Spec | Trigger    | 0.5 to 50 V (Peak) sine or pulse ≥50 ns }}
{{Spec | X input    | DC coupled via 100 K potentiometer and sweep amplifier; 1.5 V/cm or less; DC to 800 kHz }}
{{Spec | CRT        | [[5CP]], 3 kV acceleration }}
{{Spec | Calibrator | Clipped sine wave of power line frequency, ranges 0-0.3, 0-1, 0-3, 0-10, 0-30, 0-100 V<sub>p-p</sub> }}
{{Spec | Outputs    | Sweep sawtooth, 20 V<sub>p-p</sub>; Positive and negative gate, 40 V<sub>p-p</sub> }}
{{Spec | Weight    | 511 – 29 kg (65 lb); 511A – 23 kg (50 lb); }}
{{Spec | Dimensions | 15½" high, 12½" wide, 21½" deep }}
{{Spec | Power      | 511 – 180 W; 511A – 105-125 or 210-250 V, 50-60 Hz, 230 W }}
{{EndSpecs}}
(511A unless noted otherwise)
 
There is also a 511AD, where the "D" in the model number indicates that it has an L-C [[delay line]].


==Specifications==
==Prices==
The 511A does not have response down to DC.
* $795 in 1948 (~$9,700 in 2023 dollars)
The frequency range is specified as 10 Hz to 10 MHz.
There is also a 511AD.
The "D" in the model number indicates that it has a L-C [[delay line]].
The 511 weighs 65 pounds (29 kg) and consumes 180 W. 
The 511A weighs 50 pounds (23 kg) and consumes 230 W.
[[Category:Specifications needed]] ''please add''


==Internals==
==Internals==
The 511 uses a standard CRT, the [[5CP1A]].  
The 511/511A uses a standard CRT, the [[5CP1A]] (with P1 [[phosphor]]), [[5CP7A]] ([[phosphor|P7]]) or [[5CP11A]] ([[phosphor|P11]]) below S/N 5100, the [[5AB]]P from 5100 up. P1 was standard, P7 and P11 optional at no extra charge.
The vertical output of the 511A is a pair of [[6AG7]] tubes,  
 
AC-coupled to the vertical deflection plates.   
The vertical output is a pair of [[6AG7]] tubes, AC-coupled to the vertical deflection plates.  The horizontal amplifier is DC-coupled through a chain of five [[NE-2]] neons on either side for voltage offset.
 
There was an option that added a 1 μs marker generator.


Neither the 511 nor the 511A has a [[thermal cutoff]].   
Neither the 511 nor the 511A has a [[thermal cutoff]].   
The 511AD was available through 1953.


The 511 was produced with serial numbers 101 to 454.
===511===
The 511A has serial numbers 455 and up.
The original 511 was produced with serial numbers 101 to 454 (June 1947 – November 1948).  
The main difference between the 511 and the 511A is the power supply.
 
In the 511 there are two power transformers,  
There are two power transformers, T1 and T2, both operating on 60 Hz mains power with their primaries in parallel.
T1 and T2, both operating on 60 Hz mains power with their primaries in series.
T1 produces the CRT anode and cathode voltages, as well as various other regulated and unregulated voltages.   
T1 produces the CRT anode and cathode voltages, as well as various other
The CRT cathode and anode voltages (+1500/-1500 V) are simply rectified voltages from the secondary of T1.   
regulated and unregulated voltages.  The CRT cathode and anode voltages in
The lack of regulation means that variations in mains voltage results in variation of deflection sensitivity.   
the 511 are simply rectified voltages from the secondary of T1.  The lack
The +275 V and + 475V rectifier circuits have choke inputs.
of regulation means that variations in mains voltage results in variation
 
of deflection sensitivity.   
===511A (SN 455+)===
 
The main difference introduced in the 511A is the power supply. 
The regulated positive supply voltages were lowered somewhat to +225 V and +450 V, with capacitor-input circuits (no chokes).


In the 511A, the CRT cathode and anode voltages are produced by a 2 kHz oscillator  
The CRT cathode and anode voltages are produced by a 2 kHz oscillator (a [[6AQ5]]) that is powered by the +225 V<sub>DC</sub> regulated supply.  
that is powered by the 511A's +225 V<sub>DC</sub> regulated supply. This results in vertical
This results in vertical deflection calibration that is independent of mains voltage. 
deflection calibration that is independent of mains voltage.
HV rectifiers are two [[1B3GT]] tubes producing +1500/-1500 V.


The 511 and 511A use a [[6AL5]] tube (V3) as the disconnect diode for the sweep.
===511A (SN 1406+)===
Beginning with SN 1406, the 511A(D) gained a continuously variable sweep speed control, visible as a 2nd dial next to the "sweep speed multiplier".


The 511 and 511A were normally furnished with P1 [[phosphor]]. P7 and P11 were optional, at no extra charge.
===511A (SN 2406+)===
From SN 2406 upward, a dedicated calibrator stage uses one half of a [[12AT7]], V16.1, to clip a voltage derived from the mains transformer to a 100 V level divided from the regulated +225 V rail.


There was an option that added a 1 μs marker generator.
The HV rectifier uses two [[1V2]] tubes producing +1800/-1500 V.


===Delay===
===Delay===
The Tektronix Type 1-AD-25 delay was available as a factory option for the 511.
The Tektronix Type 1-AD-25 delay line, composed of 24 L-C sections, was available as a factory option for the 511A. With the delay, the scope is a 511-AD.
With the delay, the scope is a 511-AD.
Even when ordered without the delay, the 511's chassis was pre-drilled for the delay so that it could be added later, in the field, without drilling.
The delay is composed of 24 L-C sections.
The delay could be switched in and out of the signal path, presumably to avoid the slight signal degradation the delay causes.
Even when ordered without the delay, the 511's chassis was pre-drilled for the delay
 
so that it could be added later, in the field, without drilling.
The delay could be switched in and out of the signal path, presumably to avoid
the slight signal degradation the delay causes.
==History==
==History==
* See also https://vintagetek.org/tektronix-first-products/
Tektronix engineer [[Frank Hood]] recollects:
Tektronix engineer [[Frank Hood]] recollects:
<blockquote>My first assignment was to build or modify some special instruments for Bonneville Power. They wanted a device that would detect and record any lightning strikes or arc-overs on the high voltage power lines running between Vancouver, Wash. and other cities such as Longview, Spokane, etc. They wanted to detect each event, in a fraction of a millionth of a second, then to send a pulse of energy down the defective line and measure the time it took to return, (this was an application much like radar). They wanted markers displayed at each mile and fraction of a mile so that they could determine the exact location of the fault. They needed to record a photographic image for latter study. Two or more such instruments were built. We called these Type 511B. They worked very well and were used for several years.
<blockquote>My first assignment was to build or modify some special instruments for Bonneville Power. They wanted a device that would detect and record any lightning strikes or arc-overs on the high voltage power lines running between Vancouver, Wash. and other cities such as Longview, Spokane, etc. They wanted to detect each event, in a fraction of a millionth of a second, then to send a pulse of energy down the defective line and measure the time it took to return, (this was an application much like radar). They wanted markers displayed at each mile and fraction of a mile so that they could determine the exact location of the fault. They needed to record a photographic image for latter study. Two or more such instruments were built. We called these Type 511B. They worked very well and were used for several years.
Line 75: Line 96:


==Links==
==Links==
[http://richardsears.wordpress.com/2012/01/07/near-the-beginning-of-an-era-the-tektronix-511a/ Detailed article on 511A]
* [https://richardsears.wordpress.com/2012/01/07/near-the-beginning-of-an-era-the-tektronix-511a/ Richard Sears' detailed 511A Page]
* ''[Note 1]'' TekWeek March 23, 1984 says $595 but the advertised price was $795 (see below).


==Pictures==
==Pictures==
===511===
<gallery>
Tek 511 1.jpg
Tek 511 2.jpg
Tek 511 3.jpg
Tek 511 4.jpg
Vollum scope - Electronics Magazine April 1948.jpg | Vollum scope - Electronics Magazine, April 1948
Septad511.jpg|511 ad from September 1948
Tek 511 ps.png  | 511 non-A power supply schematics 
</gallery>
===511A===
<gallery>
<gallery>
Tek 511 1.jpg|511
Tek 511a 1.JPG
Tek 511 2.jpg|511
Tek 511a 2.JPG
Tek 511 3.jpg|511
Tek 511a 3.JPG
Tek 511 4.jpg|511
Tek 511a 4.JPG
Tek 511a 1.JPG|511A
Tek 511a 5.JPG
Tek 511a 2.JPG|511A
Tek 511AD top 2.jpg
Tek 511a 3.JPG|511A
Tek 511AD top 3.jpg
Tek 511a 4.JPG|511A
Tek 511AD bottom 2.jpg
Tek 511a 5.JPG|511A
Tek 511 ps.png
511a-ps.png|511A
511a-ps.png|511A
511a-vertical.png|511A
511a-vertical.png|511A
511a sweep.png|511A
511a sweep.png|511A
Septad511.jpg|511 Ad from September 1948
511A ad from Electronics 1948-11 p239.jpg | 511A ad from Electronics Magazine, November 1948, p.239
</gallery>
 
===511AD===
<gallery>
Tek 511ad 1.jpg|511AD
Tek 511ad 1.jpg|511AD
Tek 511ad 2.jpg|511AD
Tek 511ad 2.jpg|511AD
Line 98: Line 134:
Tek 511_ad4.jpg|511AD
Tek 511_ad4.jpg|511AD
</gallery>
</gallery>
==Components==
{{Parts|511}}
{{Parts|511A}}


[[Category:Monolithic tube scopes]]
[[Category:Monolithic tube scopes]]
Retrieved from "https://w140.com/tekwiki/wiki/Special:MobileDiff/31601...87830"