Pacific Measurements 1038: Difference between revisions

{{Oscilloscope Sidebar |

title=Pacific Measurements 1038 |

summary=100kHz to 18.5GHz network analyzer |

image=Pacific Measurements 1038.jpg |

caption=Pacific Measurements 1038 with Tek D11 display, PM-H13 and x2 PM-V12 plug-ins |

introduced=(?) |

discontinued=(?) |

manuals=

* [[Media:Wavetek_PMI_1038_system_overview_brochure_specification.pdf|Wavetek PMI 1038 System Brochure with Specs (PDF), courtesy of Sphere Research]]

* [[Media:PM1038_Swept_Measurement_System_Brochure_info_wo_N10_NS20.pdf|PMI 1038 Swept Measurement System Brochure 1977 (PDF), courtesy of Helmut Singer Elektronik]]

* [[Media:Pacific_Measurements_PM1038_Swept_Power_Meter_Instruction_Manual-D14.pdf|PMI 1038-D14 Mainframe Instruction Manual (PDF)]]

* [[Media:Wavetek_PMI_1038_D14A_Operating_and_Maintenance_Manual.pdf|Wavetek PMI 1038-D14A Operating and Maintenance Manual (PDF)]]

* [[Media:1038_V10_V11_V12_Instruction_Manual_full.pdf |PMI 1038-V10, -V11 and -V12 Instruction Manual (PDF)]]

The '''Pacific Measurements 1038''' is a 1 or 2 channel scalar network analyzer

incorporating a Tektronix [[5000-series scopes]] display unit, either a [[5110 | D10 long-persistance (P-7 phosphor)]],

[[5111 | D11 split-screen storage]] or a [[Introduction to the 5000-Series_Oscilloscopes|D14(?) digital storage]] model,

with optional rack mount and [[GPIB interface]].

* Horizontal plug-ins H10 (sweep drive), H11 (sweep Drive and memory address circuits), H12 (sweep drive and ratio channel), H13 (sweep drive, memory address circuits and ratio channel) and K11 (replaces H11 and provides amplitude sweep).

* Vertical plug-ins V10 (log amp and signal conditioning), V11 (log amp, signal conditioning and 256 point memory), V12 (log amp, signal conditioning and 1024 point memory), V13 (log amp, signal conditioning, recording of two calibration curves and 1024 point memory) and V20 (linear amp, 1024 point memory and for use in conjunction with Model 1018B power meter).

* N10 plug-in (dual channel network analyzer).

* NS20 plug-in (dual channel network analyzer) with optional NS201 (2 to 18.5 GHz RF source).

* C10 plug-in calibration fixture and extender kit for direct calibration and check-out of the D14/D14A Mainframe. It has extension cables to permit calibration and maintenance of the H/V system plug-ins.

* Power input calibrator unit (detector simulator - P/N 15484) will act as a "standard" detector to furnish accurate voltages to the H/V system when it is desired to calibrate the amplitude correction circuitry.

Pacific Measurements later became part of [[Wavetek]].  

{{Spec | Offset Range   | ±99.9 dB, 3 digits resolution, accuracy  ±0.02 dB/10 dB ±0.05 dB }}

{{Spec | Frequency Range | 100 kHz to 18.5 GHz ;<br /> with single diode (P/N 12685, 12882, 12883, 13161) detector, 100 kHz to 1 GHz or (P/N 13160) 2 GHz ;<br /> with single diode (P/N 15272) or balanced (P/N 15285) detector, 1 MHz to 26.5 GHz ;<br />Wavetek Pacific Measurements waveguide detector (P/N 15882), 26.5 GHz to 40.0 GHz ;<br />other waveguide manufacturers, up to 110 GHz }}

{{Spec | Dynamic Range   | 60 dB (Reference Channel: 40 dB) }}

{{Spec | Noise Floor     | −70 dB }}

{{Spec | Power          | Approx. 100 VA @ 50 − 440 Hz; 100, 120, 240 V_AC ±10% }}

{{Spec | Dimensions      | benchtop (H x W x D) 381 x 216 x 483 mm (15 x 8.5 x 19 in.);<br />rackmount (H x W x D) 178 x 483 x 483 mm (7 x 19 x 19 in.) }}

{{SpecGroup | Power Detectors (P/Ns 15272, 13782 and 13783 unless noted) }}

{{Spec | Input Impedance | 50 Ω nominal; <br /> 75 Ω (P/N 12685, 12882, 13161)}}

{{Spec | Input Power     | max. +23 dBm (200 mV) peak or average }}

{{Spec | Return Loss     | >20.8 dB, SWR <1.20 from 100 kHz to 1 GHz (P/N 12685, 12882, 12883, 13160, 13161); <br /> >25.0 dB, SWR <1.12 from 1 MHz to 1 GHz; <br /> >18.0 dB, SWR <1.29 from 2 GHz to 12.4 GHz; <br /> >14.0 dB, SWR <1.50 up to 26.5 GHz }}

{{Spec | Flatness        | ±0.5 dB to 18.5 GHz (P/N 15272); <br /> ±1.0 dB 18.5 GHz to 26.5 GHz (P/N 15272) ; <br /> ±1.0 dB to 18.5 GHz (P/N 13782) ;<br /> ±1.0 dB to 18.5 GHz (P/N 13783; <br /> ±2.0 dB with [[N connector|type N]] or [[APC7 connector]]s to 18 GHz, ±2.0 dB to 26.5 GHz with [[APC3.5 connector]]s}}

{{SpecGroup | Power Detector P/N 15882}}  

{{Spec | Input Power     | max. +20 dBm (100 mV) peak or average }}

{{Spec | Return Loss     | >10 dB, SWR <1.92 from 26.5 to 40 GHz }}

{{Spec | Cable Length   | 1.5 m (5 ft)}}

===1038-D10 with H13 & (bench model) V11, (rack model) x2 V12 Plug-Ins===

D10_Mainframe_PM1038_System.jpg | 1038-D10 H/V bench model

D10_Mainframe_rackmount_PM1038_System.jpg | 1038-D10 H/V rack model

===1038-D11 with H13 & x2 V12 Plug-Ins===

Pacific Measurements 1038.jpg  | 1038-D11 H/V bench model

===1038-D14 with H13 & x2 V12 Plug-Ins===

PacificMeasurements_1038_D14_H13_V12_front.jpg | 1038-D14 H/V bench model

===1038-D14A with N10 Plug-In===

WavetekD14A_PM1038-N10_front.jpg | 1038-D14A N10 rack model

===1038-D14 with NS20 Plug-In===

1038_NS20_1200x900_cropped.jpg | 1038-D14 NS20 bench model