2753

Tektronix 2753P
1.8 GHz Spectrum Analyzer Tektronix 2753P Produced from 1988 to 1993 Manuals Tektronix 2753P Operators Manual 070-6305-00 Tektronix 2753P Programmers Manual 070-6308-00 Tektronix 2753P Service Manual Vol. 1 070-6306-00 Tektronix 2753P Service Manual Vol. 2 070-6307-00 Tektronix 2754 introduction spec Tektronix 2754 final spec (Manuals are OCRed PDF files unless noted otherwise)

The Tektronix 2753P is a spectrum analyzer with a frequency range of 100 Hz to 1.8 GHz. The P suffix designation indicates GPIB Programmability.

Key Specifications

Frequency	100 Hz to 1.8 GHz
Frequency Span	10 Hz/div to 100 MHz/div in 1-2-5 sequence, plus 0 Hz and MAX
Resolution Bandwidth	10 Hz to 3 MHz in decade steps (-6 dB bandwidth)
RF Input impedance	50 Ω
Maximum Safe Input Power	1 Watt (+30 dBm) CW, 75 W peak (1 µs pulse, 0.1% duty factor)
RF Attenuator	0 dB to 60 dB, 10 dB steps
Reference Level	–117 dBm to +40 dBm (+30 dBm maximum safe input)
LO Output Power (2 to 6 GHz)	1st LO: +7.5 dBm to +15 dBm; 2nd LO: -22 dBm to +15 dBm; Must be terminated into 50 Ω when they are not connector to an external device
Sweep Speed	5 s to 2 µs in 1–2–5 sequence (10 s/div in auto)
Video Bandwidth	0.3 Hz to 30 kHz
Displayed Average Noise	−130 dBm
Display Dynamic Range	90 dB
Dynamic Range (Compression to noise)	134 dBm
Calibrator output	50 Ω, -20 dBm ±0.3 dB at 100 MHz
Weight	27 kg (60 lbs)
Power	90 − 132 V_AC, 48 to 448 Hz; 180 – 250 V_AC, 48 to 72 Hz. At 115 V_AC, 60 Hz, 210 W max with all options

Opt. 01: Add preselector for the 1.7 to 21 GHz band and limiter for 1st mixer below 1.8 GHz
Opt. 07: 75 Ω dBmV input and calibration in addition to 50 Ω dBm input and calibration
Opt. 23: GRASP software, National’s PC2A (GPIB) card, and GPIB cable)
Opt. 27: Epson LT-386SX, GRASP software, National’s PC2A (GPIB) card, and GPIB cable
Opt. 28: Deskpro 386S, Model 40, GRASP software, National’s PC2A (GPIB) card, and GPIB cable
Opt. 29: Epson FX-86E printer and parallel interface cable
Opt. 30: Rackmount with handles for 19 in. rack
Opt. 31: Rackmount with handles for 19 in. rack with rear panel input/output capability (no front panel inputs)
Opt. 39: Non-lithium batteries for battery-backed memory
Opt. 42: Replaces MARKER/VIDEO input port on the rear panel with a 110 MHz IF output port that provides a 3 dB signal bandwidth ≥4.5 MHz
Opt. 45: MATE/CIIL language
Opt. 52: North American 220 V configuration with standard power cord. Fuses are replaced with 2 A slo-blo