Pacific Measurements 1038: Difference between revisions

Latest revision as of 03:20, 27 September 2024

Pacific Measurements 1038

18.5 GHz network analyzer

Produced from 1974 to (?)

Manuals

(All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Pacific Measurements 1038 is a single- or dual-channel scalar network analyzer, some models of which incorporate a Tektronix 5000-series display unit − a D10 long-persistance display (P-7 phosphor) or a D11 split-screen storage display.

The PM1038-D14 has a display unit with digital storage. From manual photos and diagrams, the D14 would appear not to be a Tek OEM unit (see also Introduction to the 5000-Series Oscilloscopes regarding 5114/D14).

The PM1038 had an optional GPIB interface and was available in benchtop or rackmount configurations.

Options:

Horizontal plug-ins: H10 (sweep drive), H11 (sweep Drive and memory address circuits), H12 (sweep drive and ratio channel), H13 (sweep drive, memory address circuits and ratio channel) and K10/K11 (replaces H11 and provides amplitude sweep).
Vertical plug-ins: V10 (log amp and signal conditioning), V11 (log amp, signal conditioning and 256 point memory), V12 (log amp, signal conditioning and 1024 point memory), V13 (log amp, signal conditioning, recording of two calibration curves and 1024 point memory) and V20 (linear amp, 1024 point memory and for use in conjunction with Model 1018B power meter).
N10 plug-in (dual channel network analyzer)
NS20 plug-in (dual channel network analyzer) with optional NS201 (2 to 18.5 GHz RF source)
C10 plug-in calibration fixture and extender kit for direct calibration and check-out of the D14/D14A Mainframe. It has extension cables to permit calibration and maintenance of the H/V system plug-ins
Power input calibrator unit (detector simulator - P/N 15484) will act as a "standard" detector to furnish accurate voltages to the H/V system when it is desired to calibrate the amplitude correction circuitry

Pacific Measurements later became part of Wavetek as Wavetek Pacific Measurements and later as Wavetek Microwave.

Key Specifications

	— H/V System —
Frequency range	100 kHz to 18.5 GHz ; with single diode (P/N 12685, 12882, 12883, 13161) detector, 100 kHz to 1 GHz or (P/N 13160) 2 GHz ; with single diode (P/N 15272) or balanced (P/N 15285) detector, 1 MHz to 26.5 GHz ; Wavetek Pacific Measurements waveguide detector (P/N 15882), 26.5 GHz to 40.0 GHz ; other waveguide manufacturers, up to 110 GHz
Input power	−50 dBm to +10 dBm
Dynamic range	60 dB (Reference Channel: 40 dB)
Offset range	±99.9 dB, 3 digits resolution, accuracy ±0.02 dB/10 dB ±0.05 dB
Drift	@ 0 dBm, <0.01 dB/°C (+15° to +45°C ); @ −40 dBm, <0.5 dB/24 Hrs at constant temperature )
Reading	Insertion Loss/Gain and Return Loss, 0.02 dB resolution
Noise floor	−70 dB
	— Power detectors (P/Ns 15272, 13782 and 13783 unless noted) —
Input impedance	50 Ω nominal; 75 Ω (P/N 12685, 12882, 13161)
Input power	max. +23 dBm (200 mV) peak or average
Return loss	>20.8 dB, SWR <1.20 from 100 kHz to 1 GHz (P/N 12685, 12882, 12883, 13160, 13161); >25.0 dB, SWR <1.12 from 1 MHz to 1 GHz; >18.0 dB, SWR <1.29 from 2 GHz to 12.4 GHz; >14.0 dB, SWR <1.50 up to 26.5 GHz
Accuracy	3% to 18.5 GHz and 5% to 26.5 GHz
Flatness	±0.5 dB to 18.5 GHz (P/N 15272); ±1.0 dB 18.5 GHz to 26.5 GHz (P/N 15272) ; ±1.0 dB to 18.5 GHz (P/N 13782) ; ±1.0 dB to 18.5 GHz (P/N 13783; ±2.0 dB with type N or APC7 connectors to 18 GHz, ±2.0 dB to 26.5 GHz with 3.5 mm connectors
	— Power detector P/N 15882 —
Input power	max. +20 dBm (100 mV) peak or average
Return loss	>10 dB, SWR <1.92 from 26.5 to 40 GHz
Accuracy	0.2 dB to 2 dB from 30 MHz to 26.5 GHz, 0.5 dB to 2 dB from 26.5 GHz to 40 GHz
Flatness	±2.0 dB from 26.5 to 40 GHz

Prices

Please add

Links

Pictures

1038-D10

1038-D10 H/V bench model with H13 and V11 plug-ins
1038-D10 H/V rack model with H13 and two V12 plug-ins
1038-D10 rack model, rear

1038-D11

1038-D11 H/V bench model with H13 and two V12 plug-ins
1038-D11 bench model, rear

1038-D14

1038-D14 H/V bench model with H13 and two V12 plug-ins
1038-D14 bench model, rear

1038-D14A

1038-D14A N10 rack model with N10 plug-in
1038-D14A rack model, rear

1038-D14

1038-D14 bench model with NS20 plug-in

1038-NS201

1038-NS201
1038-NS201 rear
1038-NS201
1038-NS201 rear

1038-C10

1038-C10 calibration plug-in
1038-C10 calibration plug-in rear

1038-N10

@@ Line 1: / Line 1: @@
-{{Oscilloscope Sidebar |
+{{Instrument Sidebar
-title=Pacific Measurements 1038 |
+|class=Network Analyzer
-summary=100kHz to 18.5GHz network analyzer |
+|manufacturer=Pacific Measurements
-image=Pacific Measurements 1038.jpg |
+|series=5000-series scopes
-caption=Pacific Measurements 1038 with Tek D11 display, PM-H13 and x2 PM-V12 modules |
+|model=1038
-introduced=? |
+|summary=18.5 GHz network analyzer
-discontinued=? |
+|image=Pacific Measurements 1038.jpg
-manuals=
+|caption=Pacific Measurements 1038 with Tek D11 display, PM-H13 and two PM-V12 plug-ins
-* [[Media:Wavetek_PMI_1038_system_overview_brochure_specification.pdf|Wavetek PMI 1038 System Brochure with Specs (PDF)]]
+|introduced=1974
-* [[Media:PM1038_Swept_Measurement_System_Brochure_info_wo_N10_NS20.pdf|PMI 1038 Swept Measurement System Brochure 1977 (PDF), courtesy of Helmut Singer Elektronik]]
+|discontinued=(?)
-* [http://w140.com/wavetek_6000_ns20_application_software_manual.pdf Wavetek 6000 NS20 Application Software Manual (PDF)]
+|designers=
-* [[Media:PM_POWER_DETECTORS_MODEL_103800.PDF|PM Power Detectors Model 1038 Operating Info (PDF)]]
+|manuals=
+* [[Media:Wavetek_PMI_1038_system_overview_brochure_specification.pdf|Wavetek PMI 1038 System Brochure with Specs, courtesy of Sphere Research]]
+* [[Media:PM1038_Swept_Measurement_System_Brochure_info_wo_N10_NS20.pdf|PMI 1038 Swept Measurement System Brochure 1977, courtesy of Helmut Singer Elektronik]]
+* [https://w140.com/tek_d10.pdf Tektronix D10 Instruction Manual]
+* [[Media:PM_1038-D10_D11_Instruction_Manual.pdf |PMI 1038-D10, -D11 Mainframe Instruction Manual]]
+* [[Media:Pacific_Measurements_PM1038_Swept_Power_Meter_Instruction_Manual-D14.pdf|PMI 1038-D14 Mainframe Instruction Manual]]
+* [[Media:Wavetek_PMI_1038_D14A_Operating_and_Maintenance_Manual.pdf|Wavetek PMI 1038-D14A Operating and Maintenance Manual]]
+* [[Media:Pacific 1038-d14a.pdf|Pacific Measurements 1038-D14A Manual]] (hi-res)
+* [[Media:1038_H13_Operation_Maintenance_Manual_full.pdf |Wavetek PMI 1038-H13 Operating and Maintenance Manual]]
+* [[Media:PM_1038_H12_H13_Instruction_Manual.PDF |PMI 1038-H12 and -H13 Instruction Manual]]
+* [[Media:1038_V10_V11_V12_Instruction_Manual_full.pdf |PMI 1038-V10, -V11 and -V12 Instruction Manual]]
+* [[Media:PMI_1038-V13_Operating_and_Maintenance_Manual.pdf |PMI 1038-V13 Operating and Maintenance Manual]]
+* [[Media:Wavetek_1038_V13_Operating_and_Maintenance_Manual.pdf |Wavetek Microwave 1038-V13 Operating and Maintenance Manual]]
+* [[Media:PM_1038-C10_Instruction_Manual.pdf |PMI 1038-C10 Instruction Manual]]
+* [[Media:Pacific_Measurements_PM1038_Swept_Power_Meter_App_Note18.pdf|PMI 1038 Swept Measurement System Application Note 18]]
+* [[Media:Pacific_Measurements_PM1038_Swept_Power_Meter_App_Note19.pdf|PMI 1038 Swept Measurement System Application Note 19]]
+* [https://w140.com/wavetek_6000_ns20_application_software_manual.pdf Wavetek 6000 NS20 Application Software Manual]
+* [[Media:PM_POWER_DETECTORS_MODEL_103800.PDF|PM Power Detectors Model 1038 Operating Info]]
 * [[Media:PM_POWER_DETECTORS_MODEL_1038_specs.jpg|PM Power Detectors Model 1038 Specifications, courtesy of Sphere Research]]
+* [[Media:PMI_1018B_INSTRUCTION_MANUAL_Combined_needs_ordering.PDF|PMI 1018B Instruction Manual]] (pgs needs re-order)
+* [[Media:Wavetek pacific 1038-n10.pdf|Wavetek Pacific Measurements 1038-N10 Network Analyzer Manual]]
 }}
+The '''Pacific Measurements 1038''' is a single- or dual-channel scalar network analyzer, some models of which incorporate a [[5000-series scopes|Tektronix 5000-series display unit]] − a [[5110|D10 long-persistance display]] (P-7 phosphor) or a [[5111|D11 split-screen storage display]].
+The PM1038-D14 has a display unit with digital storage.  From manual photos and diagrams, the D14 would appear not to be a Tek OEM unit (see also [[Introduction to the 5000-Series Oscilloscopes]] regarding 5114/D14).
-<!-- [[File:Pacific Measurements 1038.jpg | thumb | 300px | right | Pacific Measurements 1038 with Tek D11 display]] -->
+The PM1038 had an optional [[GPIB interface]] and was available in benchtop or rackmount configurations.
-The '''Pacific Measurements 1038''' is a 1 or 2 channel scalar network analyzer
+Options:
-incorporating a Tektronix [[5110 | D10]] (P-7 long persistance phosphor),
+* Horizontal plug-ins: H10 (sweep drive), H11 (sweep Drive and memory address circuits), H12 (sweep drive and ratio channel), H13 (sweep drive, memory address circuits and ratio channel) and K10/K11 (replaces H11 and provides amplitude sweep).
-[[5111 | D11 storage]] (Split Screen Storage) or
+* Vertical plug-ins: V10 (log amp and signal conditioning), V11 (log amp, signal conditioning and 256 point memory), V12 (log amp, signal conditioning and 1024 point memory), V13 (log amp, signal conditioning, recording of two calibration curves and 1024 point memory) and V20 (linear amp, 1024 point memory and for use in conjunction with Model 1018B power meter).
-[[http://w140.com/tekwiki/wiki/Introduction_to_the_5000-Series_Oscilloscopes D14]]
+* N10 plug-in (dual channel network analyzer)
-[[5000-series scopes]] display unit mainframe with optional rack mount and IEEE bus.
+* NS20 plug-in (dual channel network analyzer) with optional NS201 (2 to 18.5 GHz RF source)
+* C10 plug-in calibration fixture and extender kit for direct calibration and check-out of the D14/D14A Mainframe. It has extension cables to permit calibration and maintenance of the H/V system plug-ins
+* Power input calibrator unit (detector simulator - P/N 15484) will act as a "standard" detector to furnish accurate voltages to the H/V system when it is desired to calibrate the amplitude correction circuitry
-Options were available for:
+Pacific Measurements later became part of [[Wavetek]] as Wavetek Pacific Measurements and later as Wavetek Microwave.
-* Horizontal Plug-Ins H10 (Sweep drive), H11 (Sweep Drive and memory address circuits), H12 (Sweep drive and ratio channel), H13 (Sweep drive, memory address circuits and ratio channel) and K11 (Replaces H11 and provides amplitude sweep).
-* Vertical Plug-Ins V10 (Log amp and signal conditioning), V11 (Log amp, signal conditioning and 256 point memory), V12 (Log amp, signal conditioning and 1024 point memory) and V20 (Linear amp, 1024 point memory and for use in conjunction with Model 1018B power meter).
-* N10 Plug-In (2 Channel Network Analyzer).
-* NS20 Plug-In (2 Channel Network Analyzer) with optional NS201 (2 to 18.5 GHz RF Source Module).
-* C10 Plug-In Calibration Fixture and Extender Kit for direct calibration and check out of the D14/D14A Mainframe. It has extension cables to permit calibration and maintenance of the H/V system plug-ins.
-* Power Input Calibrator Unit (Detector Simulator - P/N 15484) will act as a "Standard" detector to furnish accurate voltages to the H/V system when it is desired to calibrate the amplitde correction circuitry.
-Pacific Measurements later became part of [[Wavetek]].
 {{BeginSpecs}}
-{{Spec | H/V System | }}
+{{SpecGroup | H/V System }}
-{{Spec | -------------------- | }}
+{{Spec | Frequency range | 100 kHz to 18.5 GHz ;<br /> with single diode (P/N 12685, 12882, 12883, 13161) detector, 100 kHz to 1 GHz or (P/N 13160) 2 GHz ;<br /> with single diode (P/N 15272) or balanced (P/N 15285) detector, 1 MHz to 26.5 GHz ;<br />Wavetek Pacific Measurements waveguide detector (P/N 15882), 26.5 GHz to 40.0 GHz ;<br />other waveguide manufacturers, up to 110 GHz }}
-{{Spec | Offset Control Resolution | 3 Digits }}
+{{Spec | Input power     | −50 dBm to +10 dBm }}
-{{Spec | Offset Control Range | ±99.9dB }}
+{{Spec | Dynamic range   | 60 dB (Reference Channel: 40 dB) }}
-{{Spec | Offset Control Accuracy | ±0.02dB/10dB ±0.05dB }}
+{{Spec | Offset range    | ±99.9 dB, 3 digits resolution, accuracy  ±0.02 dB/10 dB ±0.05 dB }}
-{{Spec | Drift @ 0dBm | <0.01dB/°C (+15° to +45°C ) }}
+{{Spec | Drift           | @ 0 dBm, <0.01 dB/°C (+15° to +45°C ); <br />@ −40 dBm, <0.5 dB/24 Hrs at constant temperature ) }}
-{{Spec | Drift @ -40dBm | <0.5dB/24 Hrs at constant temperature ) }}
+{{Spec | Reading         | Insertion Loss/Gain and Return Loss, 0.02 dB resolution }}
-{{Spec | Frequency Range | 100kHz to 18.5GHz }}
+{{Spec | Noise floor     | −70 dB }}
-{{Spec | Frequency Range with Single Diode (P/N:15272)| }}
+{{SpecGroup | Power detectors (P/Ns 15272, 13782 and 13783 unless noted) }}
-{{Spec |  or Balanced (P/N:15285) Detector | 1MHz to 26.5GHz }}
+{{Spec | Input impedance | 50 Ω nominal; <br /> 75 Ω (P/N 12685, 12882, 13161)}}
-{{Spec | Frequency Range with Wavetek Pacific | }}
+{{Spec | Input power     | max. +23 dBm (200 mV) peak or average }}
-{{Spec | MeasurementsWaveguide Detector  (P/N:15882)| 26.5GHz to 40.0GHz }}
+{{Spec | Return loss     | >20.8 dB, SWR <1.20 from 100 kHz to 1 GHz (P/N 12685, 12882, 12883, 13160, 13161); <br /> >25.0 dB, SWR <1.12 from 1 MHz to 1 GHz; <br /> >18.0 dB, SWR <1.29 from 2 GHz to 12.4 GHz; <br /> >14.0 dB, SWR <1.50 up to 26.5 GHz }}
-{{Spec | Frequency Range from other | }}
+{{Spec | Accuracy        | 3% to 18.5 GHz and 5% to 26.5 GHz }}
-{{Spec | Waveguide Manufacturers | up to 110GHz }}
+{{Spec | Flatness        | ±0.5 dB to 18.5 GHz (P/N 15272); <br /> ±1.0 dB 18.5 GHz to 26.5 GHz (P/N 15272) ; <br /> ±1.0 dB to 18.5 GHz (P/N 13782) ;<br /> ±1.0 dB to 18.5 GHz (P/N 13783; <br /> ±2.0 dB with [[N connector|type N]] or [[APC7 connector]]s to 18 GHz, ±2.0 dB to 26.5 GHz with [[3.5 mm connector]]s}}
-{{Spec | Absolute (dBm) or Relative (dB) Power | -50dBm to +10dBm }}
+{{SpecGroup | Power detector P/N 15882}}
-{{Spec | Dynamic Range | 60dB }}
+{{Spec | Input power     | max. +20 dBm (100 mV) peak or average }}
-{{Spec | Dynamic Range Reference Channel | 40dB }}
+{{Spec | Return loss     | >10 dB, SWR <1.92 from 26.5 to 40 GHz }}
-{{Spec | Insertion Loss/Gain and Return Loss | 0.02dB resolution }}
+{{Spec | Accuracy        | 0.2 dB to 2 dB from 30 MHz to 26.5 GHz, 0.5 dB to 2 dB from 26.5 GHz to 40 GHz }}
-{{Spec | Noise Floor | -70dB }}
+{{Spec | Flatness        | ±2.0 dB from 26.5 to 40 GHz}}
-{{Spec | Power | Approx. 100VA @ 50 - 440Hz; 100, 120, 240VAC ±10% }}
-{{Spec | Dimensions - Bench Mount (H x W x D) | 381 x 216 x 483 mm ( 15 x 8.5 x 19 in.) }}
-{{Spec | Dimensions - Rack Mount (H x W x D) | 178 x 483 x 483 mm ( 7 x 19 x 19 in.) }}
-{{Spec | Dimensions - H/V Plug-Ins (H x W x D) | 16.8 x 6.60 x 29.7 cm ( 6.6 x 2.6 x 11.7 in.) }}
-{{Spec | Weight | 18.2kg (40lbs) }}
-{{Spec | Weight Vertical Plug-In | 2.32kg (5lbs) }}
-{{Spec | Weight Horizontal Plug-In | 2.0kg (4.4lbs) }}
-{{Spec | -------- | }}
-{{Spec | Power Detectors | P/N's 15272, 13782 and 13783 unless noted}}
-{{Spec | ------------------------ | }}
-{{Spec | Input Impedance | 50 ohms, nominal }}
-{{Spec | Maximum Input Power | +23 dBm (200mV) peak or average }}
-{{Spec | Return Loss | >25.0dB, SWR <1.12 from 1MHz to 1GHz }}
-{{Spec | Return Loss | >18.0dB, SWR <1.29 from 2 to 12.4GHz }}
-{{Spec | Return Loss | >14.0dB, SWR <1.50 up to 26.5GHz }}
-{{Spec | Accuracy | 3% to 18.5GHz and 5% to 26.5GHz }}
-{{Spec | Flatness P/N:15272| ±0.5dB to 18.5GHz }}
-{{Spec | Flatness P/N:15272| ±1.0dB 18.5 to 26.5GHz }}
-{{Spec | Flatness P/N:13782| ±1.0dB to 18.5GHz }}
-{{Spec | Flatness P/N:13783| ±1.0dB to 18.5GHz }}
-{{Spec | Flatness | ±2.0dB with type N or APC7 connectors to 18GHz }}
-{{Spec | Flatness | ±2.0dB to 26.5GHz with APC3.5 connectors}}
-{{Spec | Maximum Input Power P/N:15882 | +20 dBm (100mV) peak or average }}
-{{Spec | Return Loss P/N:15882 | >10dB, SWR <1.92 from 26.5 to 40.0GHz }}
-{{Spec | Accuracy P/N:15882 | 5% from 26.5 to 40.0GHz }}
-{{Spec | Flatness P/N:15882 | ±2.0dB from 26.5 to 40.0GHz}}
-{{Spec | Operating Temperature | 0° to 50°C }}
-{{Spec | Non-operating Temperature | -50° to +65°C }}
-{{Spec | Measurement Accuracy | 0.2dB to 2dB from 30MHz to 26.5GHz }}
-{{Spec | Measurement Accuracy | 0.5dB to 2dB from 26.5GHz to 40.0GHz }}
-{{Spec | Cable Length | 1.5m (5ft)}}
-{{Spec | Weight | Approx. 230gm (8oz) }}
 {{EndSpecs}}
-==Manuals ==
+==Prices==
 ''Please add''
-==Prices==
+==See Also==
-''Please add''
+* [[5000_Series_plug-in_interface | 5000 Series plug-in interface]]
+* [[5103 | 5103]]
+* [[5110 | 5110 (5103/D10)]]
+* [[5111 | 5111 (5103/D11)]]
 ==Links==
-* ''Sphere Research''[https://www.sphere.bc.ca/test/rf-analyzers.html]
+* [https://www.sphere.bc.ca/test/rf-analyzers.html RF Analyzers @ Sphere Research]
-* ''"MAR104 - Mobile Amateur Rain Radar" Project with Return Loss Measurement Example''[http://members.inode.at/576265/rainradar.html]
+* [http://members.inode.at/576265/rainradar.html OE2IGL: "MAR104 - Mobile Amateur Rain Radar" Project with Return Loss Measurement Example]
 ==Pictures ==
+===1038-D10===
 <gallery>
-Pacific Measurements 1038.jpg
+D10_Mainframe_PM1038_System.jpg | 1038-D10 H/V bench model with H13 and V11 plug-ins
-Pacific Measurements 1038 rear.jpg
+D10_Mainframe_rackmount_PM1038_System.jpg | 1038-D10 H/V rack model with H13 and two V12 plug-ins
-PacificMeasurements_1038_D14_H13_V12_front.jpg
+D10_Mainframe_rackmount_PM1038_System_rear.jpg | 1038-D10 rack model, rear
-PacificMeasurements_1038_D14_H13_V12_rear.jpg
-WavetekD14A_PM1038-N10_front.jpg
-WavetekD14A_PM1038-N10_back.jpg
-_NS20_1200x900_cropped.jpg
-Wavetek_1038_NS201_front_600x450.jpg
-Wavetek_1038_Ns201_600x450.jpg
 </gallery >
+===1038-D11===
+<gallery>
+Pacific Measurements 1038.jpg  | 1038-D11 H/V bench model with H13 and two V12 plug-ins
+Pacific Measurements 1038 rear.jpg | 1038-D11 bench model, rear
+</gallery >
+===1038-D14===
+<gallery>
+PacificMeasurements_1038_D14_H13_V12_front.jpg | 1038-D14 H/V bench model with H13 and two V12 plug-ins
+PacificMeasurements_1038_D14_H13_V12_rear.jpg  | 1038-D14 bench model, rear
+</gallery >
+===1038-D14A===
+<gallery>
+WavetekD14A_PM1038-N10_front.jpg | 1038-D14A N10 rack model with N10 plug-in
+WavetekD14A_PM1038-N10_back.jpg | 1038-D14A rack model, rear
+</gallery >
+===1038-D14===
+<gallery>
+_NS20_1200x900_cropped.jpg | 1038-D14 bench model with NS20 plug-in
+</gallery >
+===1038-NS201===
+<gallery>
+Wavetek_1038_NS201_front_600x450.jpg | 1038-NS201
+Wavetek_1038_Ns201_600x450.jpg | 1038-NS201 rear
+PM_1038_NS201_front.jpg | 1038-NS201
+PM_1038_NS201_rear.jpg | 1038-NS201 rear
+</gallery >
+===1038-C10===
+<gallery>
+C10_Calibrator_PMI.jpg | 1038-C10 calibration plug-in
+C10_Calibrator_PMI_rear.jpg | 1038-C10 calibration plug-in rear
+</gallery >
+===1038-N10===
+<gallery>
+Pacific 1038-N10.jpg
+</gallery>
 [[Category:Third-party products]]

Pacific Measurements 1038: Difference between revisions

Latest revision as of 03:20, 27 September 2024

Key Specifications

Prices

See Also

Links

Pictures

1038-D10

1038-D11

1038-D14

1038-D14A

1038-D14

1038-NS201

1038-C10

1038-N10

Navigation menu