2К11: Difference between revisions
Chrisjones (talk | contribs) No edit summary |
No edit summary |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{Plugin Sidebar | {{Plugin Sidebar | ||
|manufacturer=Vilnius Research | |||
summary=Calibration plugin | | |series=Soviet 7000-series clones | ||
image=2К11_front.jpg | | |type=2К11 | ||
caption=2К11 front panel | |summary=Calibration plugin | ||
|image=2К11_front.jpg | |||
introduced=(?) | | |caption=2К11 front panel | ||
discontinued=(?) | | |introduced=(?) | ||
manuals= | |discontinued=(?) | ||
|designers= | |||
|manuals= | |||
* [https://martinjonestechnology.files.wordpress.com/2017/02/2k11-technische-beschreibung-und-betriebsanleitung.pdf 2К11 Technical description and instruction manual (in German)] | * [https://martinjonestechnology.files.wordpress.com/2017/02/2k11-technische-beschreibung-und-betriebsanleitung.pdf 2К11 Technical description and instruction manual (in German)] | ||
}} | }} | ||
The '''2К11''' is a calibration plugin for [[Soviet 7000-series clones]]. It has the following operating modes: | The '''2К11''' is a calibration plugin for [[Soviet 7000-series clones]]. It has the following operating modes: | ||
* step response | * step response | ||
| Line 17: | Line 18: | ||
* readout test | * readout test | ||
The 'Y' button enables the step response mode. This generates an approx. | The 'Y' button enables the step response mode. This generates an approx. 700 kHz rectangular wave with a fast (<1 ns) edge, either falling or rising as selected by the +/- button. This enables the rise time of the mainframe to be tested. The variable amplitude control can be used to align the waveform with the graticule's rise time markers. | ||
The 'Eich.' button enables the gain test. The output of the plugin is then a | The 'Eich.' button enables the gain test. The output of the plugin is then a 500 Hz squarewave which should be exactly 6 divisions high with the variable control in the 'cal' (fully anticlockwise) position. | ||
The 'Belast.' button enables internal load resistors on the power supply rails. | The 'Belast.' button enables internal load resistors on the power supply rails. | ||
| Line 39: | Line 40: | ||
<gallery> | <gallery> | ||
2k11 front.jpg | |||
2К11_front.jpg | 2К11_front.jpg | ||
2К11_threequarter.jpg| | 2К11_threequarter.jpg| | ||
| Line 47: | Line 49: | ||
2К11_readout.jpg|readout test showing the numeral '3' in all positions | 2К11_readout.jpg|readout test showing the numeral '3' in all positions | ||
</gallery> | </gallery> | ||
[[Category:Soviet 7000-series clones]] | |||
[[Category:Vilnius Research Institute products]] | |||
Latest revision as of 23:03, 20 February 2022
The 2К11 is a calibration plugin for Soviet 7000-series clones. It has the following operating modes:
- step response
- gain
- power supply load test
- readout test
The 'Y' button enables the step response mode. This generates an approx. 700 kHz rectangular wave with a fast (<1 ns) edge, either falling or rising as selected by the +/- button. This enables the rise time of the mainframe to be tested. The variable amplitude control can be used to align the waveform with the graticule's rise time markers.
The 'Eich.' button enables the gain test. The output of the plugin is then a 500 Hz squarewave which should be exactly 6 divisions high with the variable control in the 'cal' (fully anticlockwise) position.
The 'Belast.' button enables internal load resistors on the power supply rails.
The 'Zeichen' button runs the readout test which cycles through all 64 available readout characters at approximately 1-second intervals.
Sockets are provided on the front panel for measuring the positive and negative 5 V, 15 V and 48 V supplies.
The fast rise pulse generator uses 1И305А and 1И308В tunnel diodes.
The example in the photos is labelled in German. A version labelled in Russian also exists.
Key Specifications
Links
Pictures
-
-
-
-
2K11
-
2K11
-
step response test, showing mainframe risetime about 2.5ns
-
calibration waveform, 500Hz, 6 divisions
-
readout test showing the numeral '3' in all positions
