5000 Series plug-in interface: Difference between revisions

From TekWiki
Jump to navigation Jump to search
m (Try Cite module for refs)
m (Front)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
'''[[5000-series scopes|Tektronix 5000 series oscilloscope mainframes]]''' have two vertical plug-in slots, and one horizontal plug-in slots.
'''[[5000-series scopes|Tektronix 5000 series oscilloscope mainframes]]''' have three plug-in slots; Two vertical and one horizontal.


The interconnect on either slot type is a 56-pin PCB edge connector.  
The interconnect on each slot type is a 56-pin PCB edge connector with 5/32" pitch.  


Looking into the mainframe from the front panel, "A" pins are left of the connector centerline and "B" are on the right. Pins are numbered from 1 at the bottom to 28 on the top.  
Looking into the mainframe from the front panel, "A" pins are left of the connector centerline and "B" are on the right. Pins are numbered from 1 at the bottom to 28 on the top.  


 
The table below shows the connections as if looking into the mainframe from the front.
{| class="wikitable"
{| class="wikitable"
|+ Description of signals
|+ Description of signals
Line 13: Line 13:
!width="45%"| B side<br>Function
!width="45%"| B side<br>Function
|-
|-
|-  bgcolor="LightGreen"
! 28
| Ch. 1 Col                          || Ch. 1 Row
|- bgcolor="LightGreen"
! 27
| TS1                                ||  TS4
|- bgcolor="LightGreen"
! 26
| TS8                                ||  TS9
|- bgcolor="Black"
|      ||      ||
|- bgcolor="LightGreen"
! 25
| TS3                                ||  TS2
|- bgcolor="LightGreen"
! 24
| Ch. 2 Col                          || Ch. 2 Row / Sweep rate
|- bgcolor="LightGreen"
! 23
| TS5                                ||  TS6
|- bgcolor="LightGreen"
! 22
| TS7                                ||  TS10
|-
! 21
| bgcolor="Pink" | −30 V              ||
|-
! 20
| Chop activate                      ||
|-
! 19
| 100 μs/div detect                  || Display chop
|-
! 18
| Chop sense                          || Display on
|-
! 17
| Lockout A sweep                    ||  Single sweep reset
|-
! 16
| Lockout B sweep                    ||  Trace separation
|-
! 15
| A sweep                            ||  ALT drive
|- bgcolor="Pink"
|- bgcolor="Pink"
! 1
! 14
| +200 V                             || +38 V unreg
| Clean GND Return                    || Clean GND Return
|- bgcolor="Yellow"
! 13
| +plugin signal                      || −plugin signal
|-
! 12
| Single-sweep mode                  ||
|-
! 11
| Sample pulse <ref name="note 1">[[5223]] / [[5B25N]]</ref>  || Load stop <ref name="note 1" />
|-
! 10
| A gate                             || Z Axis B Sweep
|-
!  9
| Z Axis A Sweep                      ||  Intensify
|-
!  8
|                                    ||
|- bgcolor="Yellow"
!  7
| +plugin signal                      ||  −plugin signal
|- bgcolor="Pink"
|- bgcolor="Pink"
! 2
! 6
| Utility GND                        || +5 V
| +15 V ''[54xx only!]''              ||  −15 V ''[54xx only!]''
|-
! 3
|                                    ||  Line trigger
|- bgcolor="Black"
|      ||      ||
|-
! 4
| Trig out (H) / Right trig in (V)    ||  Left trig in (V)
|- bgcolor="Pink"
|- bgcolor="Pink"
!  5
!  5
| +30 V                              || −30 V
| +30 V                              || −30 V
|-
!  4
| Trig out (H) / Right trig in (V)    ||  Left trig in (V)
|- bgcolor="Black"
|      ||      ||
|-
! 3
|                                    ||  Line trigger
|- bgcolor="Pink"
|- bgcolor="Pink"
! 6
! 2
| +15 V ''[54xx only!]''              || −15 V ''[54xx only!]''
| Utility GND                        || +5 V
|- bgcolor="Yellow"
!  7
| +plugin signal                      ||  −plugin signal
|-
!  8
|                                    ||
|-
!  9
| Z Axis A Sweep                      ||  Intensify
|-
! 10
| A gate                              || Z Axis B Sweep
|-
! 11
| Sample pulse <ref name="note 1">[[5223]] / [[5B25N]]</ref>  || Load stop <ref name="note 1" />
|-
! 12
| Single-sweep mode                  ||
|- bgcolor="Yellow"
! 13
| +plugin signal                      || −plugin signal
|- bgcolor="Pink"
|- bgcolor="Pink"
! 14
! 1
| Clean GND Return                    || Clean GND Return
| +200 V                              || +38 V unreg
|-
! 15
| A sweep                            ||  ALT drive
|-
! 16
| Lockout B sweep                    ||  Trace separation
|-
! 17
| Lockout A sweep                    ||  Single sweep reset
|-
! 18
| Chop sense                          || Display on
|-
! 19
| 100 μs/div detect                  || Display chop
|-
! 20
| Chop activate                      ||
|-
! 21
| bgcolor="Pink" | −30 V              ||
|- bgcolor="LightGreen"
! 22
| TS7                                ||  TS10
|- bgcolor="LightGreen"
! 23
| TS5                                || TS6
|- bgcolor="LightGreen"
! 24
| Ch. 2 Col                          || Ch. 2 Row / Sweep rate
|- bgcolor="LightGreen"
! 25
| TS3                                ||  TS2
|- bgcolor="LightGreen"
! 26
| TS8                                ||  TS9
|- bgcolor="LightGreen"
! 27
| TS1                                ||  TS4
|-  bgcolor="LightGreen"
! 28
| Ch. 1 Col                          || Ch. 1 Row
|}
|}


Latest revision as of 13:24, 14 August 2023

Tektronix 5000 series oscilloscope mainframes have three plug-in slots; Two vertical and one horizontal.

The interconnect on each slot type is a 56-pin PCB edge connector with 5/32" pitch.

Looking into the mainframe from the front panel, "A" pins are left of the connector centerline and "B" are on the right. Pins are numbered from 1 at the bottom to 28 on the top.

The table below shows the connections as if looking into the mainframe from the front.

Description of signals
Pin A side
Function 		B side
Function
28 Ch. 1 Col Ch. 1 Row
27 TS1 TS4
26 TS8 TS9
25 TS3 TS2
24 Ch. 2 Col Ch. 2 Row / Sweep rate
23 TS5 TS6
22 TS7 TS10
21 −30 V
20 Chop activate
19 100 μs/div detect Display chop
18 Chop sense Display on
17 Lockout A sweep Single sweep reset
16 Lockout B sweep Trace separation
15 A sweep ALT drive
14 Clean GND Return Clean GND Return
13 +plugin signal −plugin signal
12 Single-sweep mode
11 Sample pulse [1] Load stop [1]
10 A gate Z Axis B Sweep
9 Z Axis A Sweep Intensify
8
7 +plugin signal −plugin signal
6 +15 V [54xx only!] −15 V [54xx only!]
5 +30 V −30 V
4 Trig out (H) / Right trig in (V) Left trig in (V)
3 Line trigger
2 Utility GND +5 V
1 +200 V +38 V unreg

Notes

  1. ↑ 1.0 1.1 5223 / 5B25N

Pin group function legend

Plugin power & ground
HF signals
Readout system signals (5400 series only)
Retrieved from "https://w140.com/tekwiki/index.php?title=5000_Series_plug-in_interface&oldid=83847"