7912: Difference between revisions
(→R7912) |
No edit summary |
||
| Line 25: | Line 25: | ||
==R7912== | ==R7912== | ||
The '''R7912''', introduced in 1974, achieved a bandwidth of 500 MHz with a [[7A19]] vertical amplifier plug-in. It was also possible, like in the [[7904]] scope, to access the CRT deflection plates directly through a [[7A21N]] plug-in and achieve a bandwidth of 1 GHz, albeit at reduced sensitivity and loss of triggering and readout functions. | The '''R7912''', introduced in 1974, achieved a bandwidth of 500 MHz with a [[7A19]] vertical amplifier plug-in. It was also possible, like in the [[7904]] scope, to access the CRT deflection plates directly through a [[7A21N]] plug-in and achieve a bandwidth of 1 GHz, albeit at reduced sensitivity (4 V/Div) and loss of triggering and readout functions. | ||
The R7912 had a proprietary digital interface. A card for interfacing to a DEC PDP-11 was available. | The R7912 had a proprietary digital interface. A card for interfacing to a DEC PDP-11 was available. | ||
| Line 44: | Line 44: | ||
The reading of the target is asynchronous to the sweep and therefore the tube can be considered a form of scan converter. | The reading of the target is asynchronous to the sweep and therefore the tube can be considered a form of scan converter. | ||
Three output methods are provided: NTSC-out, X-Y low-speed analog, and a [[GPIB interface]] | Three output methods are provided: NTSC-out, X-Y low-speed analog, and a [[GPIB interface]]. | ||
With aftermarket modifications to the electronics, 7912AD bandwidths have been extended up to 3 GHz in special cases. | With aftermarket modifications to the electronics, 7912AD bandwidths have been extended up to 3 GHz in special cases. | ||
Revision as of 15:06, 28 February 2017
The Tektronix 7912 was a series of high-speed digitizers that take one 7000-series vertical plug-in and one 7000-series horizontal plug-in.
All 7912 models use the same internal CRT-based, digitizing scan converter tube (T7912) that is not visible from the outside. The signal from the vertical plug-in deflects a writing beam through distributed deflection plates. The electrons hit a small flat rectangular solid state target, conceptually similar to that in a digital camera. The resolution of the target is 512×512, giving 512 points in the time domain and 9-bit linear quantization of the input voltage.
With a 7B92 sweeping the whole X-axis in 5 ns, and the 7912AD capturing 512 samples in that sweep, the 7912 performs the function of a 100 GSample/s ADC.
R7912
The R7912, introduced in 1974, achieved a bandwidth of 500 MHz with a 7A19 vertical amplifier plug-in. It was also possible, like in the 7904 scope, to access the CRT deflection plates directly through a 7A21N plug-in and achieve a bandwidth of 1 GHz, albeit at reduced sensitivity (4 V/Div) and loss of triggering and readout functions.
The R7912 had a proprietary digital interface. A card for interfacing to a DEC PDP-11 was available. The Tektronix WP2000 (067-0679-00) Digital Display Controller is an external module that interfaces with the 7912. Tek also offered configurations with multiple R7912s on a common controller within the WP2000 series.
The R7912 used the 7000 series readout system writing readout characters onto the storage target, which would become part of the output signal in the NON STORE mode.
7912AD and 7912HB
From the 7912AD (1978) on, the instrument had a standard GPIB interface. The 7912AD has 500 MHz bandwidth. It was succeeded by the 750 MHz 7912HB in 1987.
For the 7912AD and 7912HB, special GPIB-controllable plug-in modules with a 'P' suffix, meaning Programmable, were available, e.g. 7A16P, 7A29P and 7B90P.
Internals
The signal goes from the vertical plug-in to the vertical amplifier to the digitizing tube where it deflects a beam of electrons.
The trace is read from the target by electronics in the 7912AD, digitized, and stored in memory. The reading of the target is asynchronous to the sweep and therefore the tube can be considered a form of scan converter.
Three output methods are provided: NTSC-out, X-Y low-speed analog, and a GPIB interface.
With aftermarket modifications to the electronics, 7912AD bandwidths have been extended up to 3 GHz in special cases.
Specifications
The Tektronix 7912AD is 19" wide, 7" tall, 27" deep, and weighs 55 pounds. It uses 360 watts maximum.
Literature and Software
- The introduction of the R7912 by Hale Farley in the Tek Retirees Newsletter 11/2012
- Thesis on "7912ADM" upgrade version
- US Patent 3748585: Silicon Diode Array Scan Converter Tube and Method of Operation. Culter et al, July 1973.
- LLE Review, Oct-Dec 1985 mentioning the LM7912A, a Lockheed-modified R7912 variant having "a bandwidth of 3.5 GHz at the -3 dB point, less than 5% undershoot and overshoot, with a 12-bit output (2 mV/bit)"
- Lockheed Palo Alto Research Lab study for LLL (June 1978) describing the LM7912 Enhanced Performance Transient Digitizer, claiming 3 GHz bandwidth
- William B. Boyer, DATA ACQUISITION AND PROCESSING ON ELECTRON BEAM FUSION ACCELERATORS. IEEE Transactions on Nuclear Science Vol.NS-25, No. 1, February 1978
Links
- Carlo Infante: A New Way to Look At Transients (R7912). In TekScope Vol. 5 No. 6, Nov-Dec 1973
- Tek R7912 @ radiomuseum.org
- Dale Aufrecht: An Intelligent, Programmable Transient Digitizer (7912AD). In TekScope Vol. 11 No. 1, 1979
- Tek 7912AD @ radiomuseum.org
See Also
Pictures
R7912
-
R7912 connected to a modern video monitor
-
R7912 front
-
R7912 controls
-
R7912 rear
7912AD
-
7912AD digitizer tube
-
7912AD block diagram
-
7912AD front
-
WP 2000
-
WP 2000
-
WP 2000
-
7912AD TV output on NTSC monitor
-
7912AD IEEE 488
-
7912AD IEEE 488
-
7912AD MPU
-
7912AD MPU
-
7912AD 5156
-
7912AD 5156
-
7912AD data buffer
-
7912AD data buffer
-
7912AD translator
-
7912AD translator
-
7912AD graticule generator
-
7912AD graticule generator
-
7912AD X-Y ramp generator
-
7912AD X-Y ramp generator
-
7912AD video processor
-
7912AD 4377
-
7912AD horizontal
-
7912AD scan amplifier
