2465: Difference between revisions
No edit summary |
No edit summary |
||
Line 22: | Line 22: | ||
* [[Media:070-4632-00.pdf|Opt.06 Opt.09 CTT/WR Service]] | * [[Media:070-4632-00.pdf|Opt.06 Opt.09 CTT/WR Service]] | ||
--> | --> | ||
====2465A==== | ====2465A==== | ||
* [[Media:070-6014-00.pdf|24x5A Operator]] (OCR PDF, 29M) | * [[Media:070-6014-00.pdf|24x5A Operator]] (OCR PDF, 29M) | ||
* [[Media:070-6017-00.pdf|2445A/2455A Service]] | |||
* [[Media:070-6019-01.pdf|2465A/2467 Service]] (OCR PDF, 29M) | * [[Media:070-6019-01.pdf|2465A/2467 Service]] (OCR PDF, 29M) | ||
* [[Media:070-5857-00.pdf|24x5A Options Service]] (OCR PDF, 26M) | * [[Media:070-5857-00.pdf|24x5A Options Service]] (OCR PDF, 26M) | ||
Line 31: | Line 31: | ||
====2465B==== | ====2465B==== | ||
* [[Media:070-6860-00.pdf| | * [[Media:070-6860-00.pdf|2445B/2455B/2465B Operator]] | ||
* [[Media:070-6863-00.pdf|2465B/2467B | * [[Media:070-6861-02.pdf|2467B Operator]] | ||
* [[Media:070-6862-00.pdf|2445B/2455B Service]] | |||
* [[Media:070-6863-01.pdf|2465B/2467B Service]] | |||
* [[Media:070-6864-02.pdf|2465B/2467B Options Service]] | |||
* [[Media:070-6873-00.pdf|2445B/2455B/2465B Service]] | |||
* [[Media:070-6882-00.pdf|2445B/2455B Service]] | |||
* [[Media:070-7148-00.pdf|2445B/2465B/2467B Quick Start]] | |||
}} | }} |
Revision as of 07:26, 26 April 2019
The Tektronix 2465 is a four-channel 300 MHz portable oscilloscope. The 2465A (1987) is a 350 MHz scope and the 2465B (1989) is the 400 MHz version.
It is the same as the 2467, except that the 2465 uses a conventional CRT while the 2467 uses a micro-channel plate CRT.
The 2465 is from the penultimate generation of analog Tektronix scopes.
The horizontal amplifier in the 2465 was designed by Art Metz and Ken Schlotzhauer. Art Metz also worked on the triggers. Art Metz and Walt Ainsworth designed the sweeps.
Options
- Option 01 (DMM) added a 4½-digit, fully autoranging digital multimeter which measures DC and AC voltage and current, resistance, dBV, dBm, continuity, and temperature.
- Option 05 (TV) added TV (back-porch) clamp circuitry to the Channel 2 input and TV trigger coupling modes, allowing selection of either horizontal or vertical sync pulses to obtain horizontal-line-sync or field-sync pulse triggering.
- Option 06 (Counter/Timer/Trigger) allows precision time-interval measurement, event and frequency counting, delay-by-events triggering, and logic triggering.
- Option 09 added option 06, the CTT, plus a 17-bit P6407 word recognizer probe.
- Option 10 added a GPIB interface for remote control.
- Option 11 added two probe-power connectors on the rear panel of the instrument. Only shown in the Tektronix catalogues for the 2465A (1987) and 2465B (1989)
- Option 46 is the designation for the military version of the scope (OS-288/G) that included option 10 IEEE-488 interface and 2 probes.
Key Specifications
— 2465 — | |
Bandwidth | 300 MHz |
— 2465A — | |
Bandwidth | 350 MHz |
— 2465B — | |
Bandwidth | 400 MHz |
— Common — | |
Sweep Rate | 500 ps/div |
Channels | Four independent channels |
Vertical | 2 mV/div vertical sensitivity |
Cursors | Delta Volts and Delta Time Cursors |
CRT Readout | Scale Factors, Trigger Level, Voltage, Time, Frequency, Phase and Ratio Measurements and Mode Indicators |
Trigger | Advanced Triggering with "Hands Off" Auto Level Triggering |
Trigger Bandwidth | 500 MHz min. |
Input Impedance | 50 Ω/1 MΩ inputs with 50 Ω protection |
Probes | Two P6131 ×10 probes, 1.3 m |
Maintenance
Note that the locations of C1115 and C1132 are swapped in the manual, so when replacing power supply capacitors, observe where the existing ones go.
Links
- Tek 2465B page @ amplifier.cd
- Tektronix 2465B oscilloscope teardown @ EEVblog forum (lots of nice internal pictures)
- How to enter test mode
Pictures
2465
-
2465
-
2465 Main Board
-
-
2465A
-
2465A
-
-
-
-
-
2465B
-
2465B (photo by Alex Schonfeld)
-
2465B (photo by Alex Schonfeld)
-
2465B (photo by Alex Schonfeld)
-
2465B (photo by Alex Schonfeld)
-
2465B (photo by Alex Schonfeld)
2465BDV
-
2465BDV
-
2465BDV
-
2465BDV
-
2465BDV