7A22: Difference between revisions
No edit summary |
No edit summary |
||
| Line 13: | Line 13: | ||
* [[Media:TB-9-6625-2132-35.pdf | TB 9-6625-2132-35 Calibration Procedure for AM-6881/U (7A13) and AM-6786/U (7A22)]] (PDF, 2M) | * [[Media:TB-9-6625-2132-35.pdf | TB 9-6625-2132-35 Calibration Procedure for AM-6881/U (7A13) and AM-6786/U (7A22)]] (PDF, 2M) | ||
}} | }} | ||
The ''' | The '''Tektronix 7A22''' is a single channel differential vertical amplifier for the [[7000-series scopes|7000 series mainframes]], produced from about 1969 to 1991. Specifications and controls are similar to the [[26A2]] and the [[3A9]] from the 560 series but without current probe input or front panel signal output. | ||
Remarkably, the 7A22's input sensitivity reaches down to 10 μV/Div. Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz. A separate control optionally supplies an internal DC voltage to offset the DC signal component. Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V. Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges. | Remarkably, the 7A22's input sensitivity reaches down to 10 μV/Div. Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz. A separate control optionally supplies an internal DC voltage to offset the DC signal component. Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V. Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges. | ||
Revision as of 04:56, 9 August 2021
The Tektronix 7A22 is a single channel differential vertical amplifier for the 7000 series mainframes, produced from about 1969 to 1991. Specifications and controls are similar to the 26A2 and the 3A9 from the 560 series but without current probe input or front panel signal output.
Remarkably, the 7A22's input sensitivity reaches down to 10 μV/Div. Bandwidth is 1 MHz, the upper 3 dB limit can be reduced in ×3 steps down to 100 Hz (to eliminate noise, inter alia), and the lower bandwidth can be raised in ×10 steps from 0.1 Hz to 10 kHz. A separate control optionally supplies an internal DC voltage to offset the DC signal component. Even in the most sensitive ranges (10 μV/Div to 10 mV/Div), common-mode voltage can be ±10 V. Input resistance is 1 MΩ, but for high source resistance DC coupled measurements, one can disconnect the internal gate return resistors of the input FETs, at the disadvantage of disabling the 20 mV/div and higher ranges.
Applications include audio, biological signals, sensors etc.
An example application is found in Jim Williams' LT Application Note 124 – see Appendix D for a comparison of differential amplifiers.
Key Specifications
Template:Spec 2Template:Spec 2Template:Spec 2Template:Spec 2| Range | Differential signal | DC Offset | Common mode |
|---|---|---|---|
| 10 μV/Div to 10 mV/Div | ±1 V | ±1 V | ±10 V |
| 20 mV/Div to 0.1 V/Div | ±10 V | ±10 V | ±100 V |
| 0.2 V/Div to 1 V/Div | ±100 V | ±100 V | ±500 V |
| 2 V/Div to 10 V/Div | ±1000 V | ±1000 V | ±500 V |
Internals
The differential amplifier design is a variant of the 1A7A circuit, also used with modifications in the 3A9, 5A22N, AM502, and 5030/5031 (26A2 too?).
The 7A22 uses the ±50 V supplies provided by the mainframe.
Prices
| Year | 1970 | 1971 | 1980 | 1984 | 1990 |
|---|---|---|---|---|---|
| Catalog price | $500 | $500 | $1,060 | $1,590 | $2,260 |
| 2018 value | $3,240 | $3,110 | $3,240 | $3,850 | $4,350 |
Pictures
Plug-in
-
7A22 front view
-
-
-
-
left side
-
left side (with cover)
-
right side
Measurements
-
7A22: 1 kHz, 130 μVp-p triangle, BW=1 MHz
-
7A22: 1 kHz, 130 μVp-p triangle, BW=100 kHz
-
7A22: 1 kHz, 130 μVp-p triangle, BW=10 kHz
-
7A22: 1 kHz, 130 μVp-p triangle, BW=1 kHz
-
15 μV p-p triangle wave displayed in variable-persistence storage mode on a 7613 for noise filtering
