7S14: Difference between revisions
No edit summary |
(specs table) |
||
| Line 11: | Line 11: | ||
* [http://w140.com/7s14_instruction.pdf Tektronix 7S14 Instruction Manual (PDF)] | * [http://w140.com/7s14_instruction.pdf Tektronix 7S14 Instruction Manual (PDF)] | ||
}} | }} | ||
The 7S14 is a 1 GHz dual-trace delayed sweep sampler plug-in. | The '''Tektronix 7S14''' is a 1 GHz dual-trace delayed sweep sampler plug-in. | ||
It is a complete sampling system unlike, for example, the [[7S12]], | It is a complete sampling system unlike, for example, the [[7S12]], | ||
which requires a separate timing plug-in to provide triggering | which requires a separate timing plug-in to provide triggering | ||
| Line 18: | Line 18: | ||
The 7S14 contains two samplers, trigger and sweep circuitry, and circuitry to interface it with the 7000-series mainframe in which it operates. The mainframe provides the 7S14 with power. The 7S14 sends the mainframe horizontal, vertical and readout signals. | The 7S14 contains two samplers, trigger and sweep circuitry, and circuitry to interface it with the 7000-series mainframe in which it operates. The mainframe provides the 7S14 with power. The 7S14 sends the mainframe horizontal, vertical and readout signals. | ||
There are two 1. | There are two 1.35 V mercury button cells, BT1 and BT2, in the sampler circuit. | ||
They act as floating bias sources, so if a 7S14 stops working it may be not defective, | They act as floating bias sources, so if a 7S14 stops working it may be not defective, | ||
just dead batteries. First check the voltage on the cells. | just dead batteries. First check the voltage on the cells. | ||
| Line 32: | Line 32: | ||
In triggered mode, the signal passes through two stages of | In triggered mode, the signal passes through two stages of | ||
[[MC1672]] ECL logic gate, and then into the [[155-0109]] trigger chip. | [[MC1672]] ECL logic gate, and then into the [[155-0109]] trigger chip. | ||
In HF-sync mode, the 7S14 uses a [[BD4]] back diode (0. | In HF-sync mode, the 7S14 uses a [[BD4]] back diode (0.1 mA, 3 pF), and inductor, and a | ||
[[152-0177-00]] tunnel diode ( | [[152-0177-00]] tunnel diode (10 mA, 4 pF) to form an oscillator that oscillates | ||
somewhere between 16. | somewhere between 16.5 MHz and 25 MHz. | ||
The sampler used by the 7S14 is a two-diode design. | The sampler used by the 7S14 is a two-diode design. | ||
| Line 40: | Line 40: | ||
==Specifications== | ==Specifications== | ||
{{BeginSpecs}} | |||
{{Spec| Rise time | 350 ps (1 GHz bandwidth) }} | |||
{{Spec| Vertical deflection | 2 mV/Div to 0.5 V/Div in 1—2—5 sequence }} | |||
{{Spec| Sweep rate | 100 µs/Div to 100 ps/Div in 1—2—5 sequence }} | |||
{{Spec| Input impedance | 50 Ω }} | |||
{{Spec| Maximum input voltage | 5 V peak }} | |||
{{Spec| Features | | |||
* Dual channel, CH1 / CH2 / Dual / Add / X—Y modes | |||
* Delayed timebase | * Delayed timebase | ||
* | * DC Offset controls | ||
}} | |||
{{EndSpecs}} | |||
==Links== | ==Links== | ||
Revision as of 08:20, 4 June 2014
The Tektronix 7S14 is a 1 GHz dual-trace delayed sweep sampler plug-in. It is a complete sampling system unlike, for example, the 7S12, which requires a separate timing plug-in to provide triggering and sampling pulse generation.
The 7S14 contains two samplers, trigger and sweep circuitry, and circuitry to interface it with the 7000-series mainframe in which it operates. The mainframe provides the 7S14 with power. The 7S14 sends the mainframe horizontal, vertical and readout signals.
There are two 1.35 V mercury button cells, BT1 and BT2, in the sampler circuit. They act as floating bias sources, so if a 7S14 stops working it may be not defective, just dead batteries. First check the voltage on the cells. When the mercury cells die, you can replace them with other (less toxic) methods of bias voltage generation. Two obvious solutions are photovoltaic cells or modern batteries. The issue has been discussed extensively on the Yahoo TekScopes forum, so search the archives there for more information. Notably, Ed Breya posted detailed notes on the 7S14 bias cell issue.
The 7S14 has an integrated delay measurement function.
The 7S14 has two triggering modes: triggered and HF-sync. In triggered mode, the signal passes through two stages of MC1672 ECL logic gate, and then into the 155-0109 trigger chip. In HF-sync mode, the 7S14 uses a BD4 back diode (0.1 mA, 3 pF), and inductor, and a 152-0177-00 tunnel diode (10 mA, 4 pF) to form an oscillator that oscillates somewhere between 16.5 MHz and 25 MHz.
The sampler used by the 7S14 is a two-diode design. Each of the two input channels has its own sampler.
Specifications
Key Specifications
| Rise time | 350 ps (1 GHz bandwidth) |
|---|---|
| Vertical deflection | 2 mV/Div to 0.5 V/Div in 1—2—5 sequence |
| Sweep rate | 100 µs/Div to 100 ps/Div in 1—2—5 sequence |
| Input impedance | 50 Ω |
| Maximum input voltage | 5 V peak |
| Features |
|
Links
Pictures
-
Sampler schematic
-
Trigger schematic
