2710

Tektronix 2710
1.8 GHz Spectrum Analyzer Tektronix 2710 Produced from 1987 to 1993 Manuals Tektronix 2710 Operators Manual (PDF, OCR) Tektronix 2710 GPIB Programmers Manual (PDF, OCR) Tektronix 2710 Service Manual (PDF, OCR) Tektronix 2710 Option 04 Manual Change Information Media:Mod 2710F04 opt04 internal tracking gen.pdf (All manuals in PDF format unless noted otherwise)

Manuals – Specifications – Links – Pictures

The Tektronix 2710 is a spectrum analyzer with a frequency range of 10 kHz to 1.8 GHz.

Key Specifications

Frequency	10 kHz to 1.8 GHz
Frequency Span	10 kHz/div to 100 MHz/div in 1–2–5 sequence, plus 0 Hz and MAX: 180 MHz/div
Resolution Bandwidth	3 kHz, 30 kHz, 300 kHz, and 5 MHz (–6 dB); 300 Hz with Opt. 01
RF Input	50 Ω, max. +20 dBm (0.1 W or 2.2 V) CW, ≤100 V DC (blocking capacitor)
RF Attenuator	0 dB to 50 dB, 2 dB steps
Sensitivity	–117 dBm at 3 kHz RBW, –129 dBm at 3 kHz RBW w/preamp
Reference Level	–70 dBm to +20 dBm; –23 dBmV to +66.9 dBmV
Sweep Speed	2 sec/Div to 1 µs/Div in 1–2–5 sequence
Triggering Modes	Free Run, Internal, External, Line, TV Line, and TV Field
Displayed Average Noise	−66 dBm to −100 dBm
Display Dynamic Range	80 dB
Dynamic Range	≥100 dBm
Internal Calibrator	100 MHz marker at –30 dBm
Weight	Standard accessories: 11.25 kg (<25 lbs); Basic configuration: 9.5 kg (<21 lbs)
Power	90 − 132 V_AC, 48 to 440 Hz; 90 – 250 V_AC, 47 to 63 Hz, 90 W (standard) / 105 W max (with options)
Operating Environment	0 °C to +50 °C; Humidity: MIL-T-28800E; Altitude: Up to 4.6 km (15,000 ft)
Features	28KB non-volatile memory (NVRAM) for up to 18 displays of waveforms and markers, and up to 9 front panel setups, user-defined key programs, and antenna factor tables Single and delta markers for readout of frequency and amplitude analog display capability, TV Line and TV Field triggering to provide demodulation of video carriers internal audio amplifier and AM/FM detectors digital storage (positive peak only, positive/negative peak, max hold, waterfall) alternate reference level units (dBm, dBmV, dBV, dBµV, dBµW, and dBµV/m) direct plot/print via Opt. 03 GPIB or Centronics interface Opt. 09

Options

Opt. 01: 300 Hz Resolution Bandwidth filter; Phase-lock with span/div ≤20 kHz
Opt. 02: Frequency Counter, 1 Hz or 1 kHz, menu selectable
Opt. 03: GPIB Interface (cannot be combined with Opt. 09)
Opt. 04: TG Tracking Generator, 100 kHz to 1.8 GHz (cannot be combined with Opt. 14)
Opt. 06: Battery Power Option (2704 Inverter and 2705 Battery Pack)
Opt. 08: Replace GPIB with RS-232-C (cannot be combined with Opt. 03)
Opt. 09: Centronix interface (cannot be combined with Opt. 03)
Opt. 10: Video Monitor mode
Opt. 11: Non-volatile RAM storage for setups, displays, and user-definable key sequences
Opt. 14: Adds Resolution Bandwidths of 1 kHz, 10 kHz, 100 kHz, and 1 MHz (cannot be combined with Opt. 04)
Opt. 15: Tek 1405 TV Sideband Adapter interface installed at J101 as SMA female
Opt. 30: Rackmount
Opt. 33: Travel Line Package
Opt. 34: Portable to Rackmount Adapter.

See also the 2706 preselector and 2707 tracking generator.

Connectors

Front panel: RF INPUT N connector (50Ω, +20 dBm Max, 100 V DC blocking capacitor); and GEN N connector (50Ω, 0 to -48 dBm, Opt. 4 Tracking Generator generates a sweep frequency to enable the Spectrum Analyzer to make circuit response measurements, i.e. scalar network analysis).

Rear panel: J101 SMA connector (Female SMA installed for Opt. 15), J102 EXT TRIG BNC connector (10 kΩ, 35V (DC + peak AC)), J103 DB9 connector (Not RS-232 compatible. Accessory connector: Pin 1 Video Input, Pin 2 Ground, Pin 3 Video Output, Pin 6 Sweep Gate, Pin 7 Sweep Output, all others unused), J104 GPIB connector

Originally included accessories

Operator’s Manual; Power Cord; Front Cover; Adapter 50 Ω N Male to BNC Female, 75 Ω to 50 Ω Minimum Loss Attenuator N Male to BNC Female

Pictures