663
edits
P64xx input leads: Difference between revisions
m
length
ElectroRents (talk | contribs) m (sorted lead set list by part number) |
m (length) |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
Original input lead sets were | Original input lead sets were | ||
* 012-0386-00 − ten individual leads | |||
* 012-0556-00 − diagnostic leads to connect [[P6460]] to diagnostic test points and test pattern generator outputs of [[1240]]/[[1241]] logic analyzers | * 012-0556-00 − diagnostic leads to connect [[P6460]] to diagnostic test points and test pattern generator outputs of [[1240]]/[[1241]] logic analyzers | ||
* 012-0655-01 − ten individual 40 cm leads | * 012-0655-01 − ten individual 40 cm leads | ||
| Line 10: | Line 11: | ||
* 012-0747-00 − standard 10-wire 10 in/25 cm with pluggable probe tips | * 012-0747-00 − standard 10-wire 10 in/25 cm with pluggable probe tips | ||
* 012-0800-00 − 10-wire 10 cm | * 012-0800-00 − 10-wire 10 cm | ||
* 012-0926-00 − 20 twisted pair leads. Possibly provided with [[P6455]], [[P6456]] and [[P6457]] pattern generator probes. | |||
* 012-0987-00 − 10-wire 5 in/12 cm with pluggable probe tips [[P6460]] | |||
* 012-0989-00 − 10-wire 5 in/12 cm with pluggable probe tips | * 012-0989-00 − 10-wire 5 in/12 cm with pluggable probe tips | ||
* 012-0990-00 − 2 pin interface to single grabber | |||
* [[012-1000-00]] − diagnostic lead set for the [[P6452]] logic probe. | * [[012-1000-00]] − diagnostic lead set for the [[P6452]] logic probe. | ||
* [[012-1053-00]] − 16 twisted pair plus | * [[012-1053-00]] − 16 twisted pair leads plus 2 grabbers for [[P6452]] | ||
* [[103-0209-00]] − 2 x ten bundled leads connecting to a standard [[GPIB connector]] ,to be used with two probes. Supplied with the [[DF2]] | * [[103-0209-00]] − 2 x ten bundled leads connecting to a standard [[GPIB connector]], to be used with two probes. Supplied with the [[DF2]] | ||
As the probe-side input connector is a standard .65 mm square pin header on a 0.2" (5.08 mm) pitch, | As the probe-side input connector is a standard .65 mm square pin header on a 0.2" (5.08 mm) pitch, | ||
it is also possible to use standard jumper wires with pins, sockets or clips on the other end for connecting inputs. | it is also possible to use standard jumper wires with pins, sockets or clips on the other end for connecting inputs. | ||
==Instructions== | ==Instructions== | ||
* [[Media: | * [[Media:070-4675-00.pdf|Instructions for 012-0556-00 diagnostics leads]] | ||
==Pictures== | ==Pictures== | ||
<gallery> | <gallery> | ||
P6408 1.jpg | [[P6408]] with 012-0747-00 harness and clips | P6408 1.jpg | [[P6408]] with 012-0747-00 harness and clips | ||
P64xx-jumper.jpg | Using P64xx probes with jumper wires | P64xx-jumper.jpg | Using P64xx probes with jumper wires | ||
012-0556-00_01.jpg | 012-0556-00 | |||
012-0747-00_01.jpg | 012-0747-00 Standard 10 lead set | |||
012-0926-00_01.jpg | 012-0926-00 | |||
012-0987-00_01.jpg | 012-0987-00 | |||
012-0990-00_01.jpg | 012-0990-00 Grabber with 2 pin interface for 64xx probes. | |||
012-0990-00_02.jpg | 012-0990-00 | |||
</gallery> | </gallery> | ||