1S1: Difference between revisions

Jump to navigation Jump to search
278 bytes added ,  9 May 2014
no edit summary
No edit summary
No edit summary
Line 1: Line 1:
{{Plugin Sidebar|
title=Tektronix 1S1|
summary=Sampling system|
image=1s1_front.jpg |
caption=1S1 front view|
years=1965 – 1973|
type=Combined|
series=[[500-series scopes]]|
manuals=
* [http://bama.edebris.com/download/tek/1s1/1s1.djvu Tektronix 1S1 Manual (DjVu)]
* [http://w140.com/1s1.pdf Tektronix 1S1 Manual (PDF)]
}}
The 1S1 is a [[sampling oscilloscope|sampling]] plug-in for [[500-series scopes]].   
The 1S1 is a [[sampling oscilloscope|sampling]] plug-in for [[500-series scopes]].   
It is essentially one channel of a sampling unit and a timing unit from a [[661]].   
 
It has its own trigger and timebase.   
It is essentially one channel of a sampling unit and a timing unit from a [[661]].  It has its own trigger and timebase.   
The oscilloscope's timebase is usually set to a relatively slow sweep rate when using a 1S1.   
 
Alternatively, the sweep on the oscilloscope can be free-run,  
The oscilloscope's timebase is usually set to a relatively slow sweep rate when using a 1S1.  Alternatively, the sweep on the oscilloscope can be free-run,  
and the horizontal voltage from the oscilloscope can be used to control the 1S1, as described below.  
and the horizontal voltage from the oscilloscope can be used to control the 1S1, as described below.  
The 1S1 has a 50-Ohm [[Connectors#GR-874|GR-874]] connector for signal input.   
 
The plug-in supplies power (+100V and -12.6V) to active probes such as the [[P6032]] cathode follower probe.   
The 1S1 has a 50 Ω [[Connectors#GR-874|GR-874]] connector for signal input.  The plug-in supplies power (+100 V and -12.6 V) to active probes such as the [[P6032]] cathode follower probe.   


The 1S1 can operate in normal self-swept mode or an external sweep signal can be applied to the 1S1.   
The 1S1 can operate in normal self-swept mode or an external sweep signal can be applied to the 1S1.   
Line 22: Line 35:
For example, one might want to know, when testing a logic gate, what is the propagation delay  
For example, one might want to know, when testing a logic gate, what is the propagation delay  
such that 99.9% of the transitions happen faster than this.   
such that 99.9% of the transitions happen faster than this.   
The horizontal-in voltage can also be produced, in "manual" mode, by setting a knob on the 1S1.
The horizontal-in voltage can also be produced, in "manual" mode, by setting a knob on the 1S1.


The sampler in the 1S1 is quite different from the sampler in the [[1S2]].   
The sampler in the 1S1 is quite different from the sampler in the [[1S2]].  The 1S1 uses a [[sampling diodes|four-diode]] sampling bridge, terminated within the 1S1.  The 1S2 uses a two-diode feed-through sampler, typical for TDR instruments.
The 1S1 uses a [[sampling diodes|four-diode]]
sampling bridge, terminated within the 1S1.  The 1S2 uses a two-diode feed-through sampler, typical for  
TDR instruments.


Type 1S1 was [[introduced in 1965]] and sold through 1973.
Type 1S1 was [[introduced in 1965]] and sold through 1973.


* [http://bama.edebris.com/download/tek/1s1/1s1.djvu Tektronix 1S1 Manual (DjVu)]
==Pictures==
* [http://w140.com/1s1.pdf Tektronix 1S1 Manual (PDF)]


<gallery>
<gallery>
Line 39: Line 49:
Image:1s1 block.jpg|block diagram
Image:1s1 block.jpg|block diagram
</gallery>
</gallery>
[[Category:Sampling plugins]]
[[Category:500 series vertical plugins]]

Navigation menu